Re: [PATCH v2] ARM: msm: Update the references to DEBUG_MSM_UARTx

From: Paul Bolle
Date: Thu Jun 19 2014 - 04:16:24 EST


On Mon, 2014-05-26 at 19:37 +0300, Georgi Djakov wrote:
> The Kconfig options DEBUG_MSM_UART1, DEBUG_MSM_UART2, DEBUG_MSM_UART3,
> MSM_DEBUG_UART1, MSM_DEBUG_UART2 and MSM_DEBUG_UART3 are removed, but
> they are still referenced in the following files:
> arch/arm/mach-msm/io.c,
> arch/arm/mach-msm/board-trout.c
> arch/arm/mach-msm/board-trout-gpio.c
>
> Fix this by updating the reference to the new Kconfig option.
>
> Reported-by: Paul Bolle <pebolle@xxxxxxxxxx>
> Signed-off-by: Georgi Djakov <gdjakov@xxxxxxxxxx>
> ---

This patch is included neither in v3.16-rc1 nor in next-20140619. Did it
run into problems or is it already queued somewhere?

> Changes since v1:
> - Fixed similar issue in board-trout.c and board-trout-gpio.c
>
> Applies to next-20140526.
>
> arch/arm/mach-msm/board-trout-gpio.c | 2 +-
> arch/arm/mach-msm/board-trout.c | 2 +-
> arch/arm/mach-msm/io.c | 6 ++----
> 3 files changed, 4 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm/mach-msm/board-trout-gpio.c b/arch/arm/mach-msm/board-trout-gpio.c
> index 87e1d01..e24930e 100644
> --- a/arch/arm/mach-msm/board-trout-gpio.c
> +++ b/arch/arm/mach-msm/board-trout-gpio.c
> @@ -94,7 +94,7 @@ static int trout_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
> }
>
> static struct msm_gpio_chip msm_gpio_banks[] = {
> -#if defined(CONFIG_MSM_DEBUG_UART1)
> +#if defined(CONFIG_DEBUG_MSM_UART) && (CONFIG_DEBUG_UART_PHYS == 0xa9a00000)
> /* H2W pins <-> UART1 */
> TROUT_GPIO_BANK("MISC2", 0x00, TROUT_GPIO_MISC2_BASE, 0x40),
> #else
> diff --git a/arch/arm/mach-msm/board-trout.c b/arch/arm/mach-msm/board-trout.c
> index 015d544..8369dfd 100644
> --- a/arch/arm/mach-msm/board-trout.c
> +++ b/arch/arm/mach-msm/board-trout.c
> @@ -90,7 +90,7 @@ static void __init trout_map_io(void)
> msm_map_common_io();
> iotable_init(trout_io_desc, ARRAY_SIZE(trout_io_desc));
>
> -#ifdef CONFIG_MSM_DEBUG_UART3
> +#if defined(CONFIG_DEBUG_MSM_UART) && (CONFIG_DEBUG_UART_PHYS == 0xa9c00000)
> /* route UART3 to the "H2W" extended usb connector */
> writeb(0x80, TROUT_CPLD_BASE + 0x00);
> #endif
> diff --git a/arch/arm/mach-msm/io.c b/arch/arm/mach-msm/io.c
> index 34e0947..b042dca 100644
> --- a/arch/arm/mach-msm/io.c
> +++ b/arch/arm/mach-msm/io.c
> @@ -57,8 +57,7 @@ static struct map_desc msm_io_desc[] __initdata = {
> .length = MSM_SHARED_RAM_SIZE,
> .type = MT_DEVICE,
> },
> -#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \
> - defined(CONFIG_DEBUG_MSM_UART3)
> +#if defined(CONFIG_DEBUG_MSM_UART)
> {
> /* Must be last: virtual and pfn filled in by debug_ll_addr() */
> .length = SZ_4K,
> @@ -76,8 +75,7 @@ void __init msm_map_common_io(void)
> * pages are peripheral interface or not.
> */
> asm("mcr p15, 0, %0, c15, c2, 4" : : "r" (0));
> -#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \
> - defined(CONFIG_DEBUG_MSM_UART3)
> +#if defined(CONFIG_DEBUG_MSM_UART)
> #ifdef CONFIG_MMU
> debug_ll_addr(&msm_io_desc[size - 1].pfn,
> &msm_io_desc[size - 1].virtual);


Paul Bolle

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/