Re: [PATCH v7 2/4] pinctrl: cygnus: add gpio/pinconf driver

From: Ray Jui
Date: Tue Feb 03 2015 - 21:20:29 EST




On 2/3/2015 5:41 PM, Dmitry Torokhov wrote:
> On Tue, Feb 03, 2015 at 05:09:06PM -0800, Ray Jui wrote:
>> This adds the initial support of the Broadcom Cygnus GPIO/PINCONF driver
>> that supports all 3 GPIO controllers on Cygnus including the ASIU GPIO
>> controller, the chipCommonG GPIO controller, and the always-on GPIO
>> controller. Basic PINCONF configurations such as bias pull up/down, and
>> drive strength are also supported in this driver.
>>
>> Pins from the ASIU GPIO controller can be individually muxed to GPIO
>> function, through interaction with the Cygnus IOMUX controller
>>
>> Signed-off-by: Ray Jui <rjui@xxxxxxxxxxxx>
>> Reviewed-by: Scott Branden <sbranden@xxxxxxxxxxxx>
>> ---
>> drivers/pinctrl/bcm/Kconfig | 22 +
>> drivers/pinctrl/bcm/Makefile | 1 +
>> drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c | 920 +++++++++++++++++++++++++++++
>> 3 files changed, 943 insertions(+)
>> create mode 100644 drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c
>>
>> diff --git a/drivers/pinctrl/bcm/Kconfig b/drivers/pinctrl/bcm/Kconfig
>> index eb13201..cd11d4d 100644
>> --- a/drivers/pinctrl/bcm/Kconfig
>> +++ b/drivers/pinctrl/bcm/Kconfig
>> @@ -20,6 +20,28 @@ config PINCTRL_BCM2835
>> select PINMUX
>> select PINCONF
>>
>> +config PINCTRL_CYGNUS_GPIO
>> + bool "Broadcom Cygnus GPIO (with PINCONF) driver"
>> + depends on OF_GPIO && ARCH_BCM_CYGNUS
>> + select GPIOLIB_IRQCHIP
>> + select PINCONF
>> + select GENERIC_PINCONF
>> + default ARCH_BCM_CYGNUS
>> + help
>> + Say yes here to enable the Broadcom Cygnus GPIO driver.
>> +
>> + The Broadcom Cygnus SoC has 3 GPIO controllers including the ASIU
>> + GPIO controller (ASIU), the chipCommonG GPIO controller (CCM), and
>> + the always-ON GPIO controller (CRMU/AON). All 3 GPIO controllers are
>> + supported by this driver.
>> +
>> + All 3 Cygnus GPIO controllers support basic PINCONF functions such
>> + as bias pull up, pull down, and drive strength configurations, when
>> + these pins are muxed to GPIO.
>> +
>> + Pins from the ASIU GPIO can be individually muxed to GPIO function,
>> + through interaction with the Cygnus IOMUX controller.
>> +
>> config PINCTRL_CYGNUS_MUX
>> bool "Broadcom Cygnus IOMUX driver"
>> depends on (ARCH_BCM_CYGNUS || COMPILE_TEST)
>> diff --git a/drivers/pinctrl/bcm/Makefile b/drivers/pinctrl/bcm/Makefile
>> index bb6beb6..2b2f70e 100644
>> --- a/drivers/pinctrl/bcm/Makefile
>> +++ b/drivers/pinctrl/bcm/Makefile
>> @@ -2,4 +2,5 @@
>>
>> obj-$(CONFIG_PINCTRL_BCM281XX) += pinctrl-bcm281xx.o
>> obj-$(CONFIG_PINCTRL_BCM2835) += pinctrl-bcm2835.o
>> +obj-$(CONFIG_PINCTRL_CYGNUS_GPIO) += pinctrl-cygnus-gpio.o
>> obj-$(CONFIG_PINCTRL_CYGNUS_MUX) += pinctrl-cygnus-mux.o
>> diff --git a/drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c b/drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c
>> new file mode 100644
>> index 0000000..cfe4478
>> --- /dev/null
>> +++ b/drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c
>> @@ -0,0 +1,920 @@
>> +/*
>> + * Copyright (C) 2014-2015 Broadcom Corporation
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + * This file contains the Broadcom Cygnus GPIO driver that supports 3
>> + * GPIO controllers on Cygnus including the ASIU GPIO controller, the
>> + * chipCommonG GPIO controller, and the always-on GPIO controller. Basic
>> + * PINCONF such as bias pull up/down, and drive strength are also supported
>> + * in this driver.
>> + *
>> + * Pins from the ASIU GPIO can be individually muxed to GPIO function,
>> + * through the interaction with the Cygnus IOMUX controller
>> + */
>> +
>> +#include <linux/kernel.h>
>> +#include <linux/slab.h>
>> +#include <linux/module.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/io.h>
>> +#include <linux/gpio.h>
>> +#include <linux/ioport.h>
>> +#include <linux/of_device.h>
>> +#include <linux/of_irq.h>
>> +#include <linux/pinctrl/pinctrl.h>
>> +#include <linux/pinctrl/pinmux.h>
>> +#include <linux/pinctrl/pinconf.h>
>> +#include <linux/pinctrl/pinconf-generic.h>
>> +
>> +#include "../pinctrl-utils.h"
>> +
>> +#define CYGNUS_GPIO_DATA_IN_OFFSET 0x00
>> +#define CYGNUS_GPIO_DATA_OUT_OFFSET 0x04
>> +#define CYGNUS_GPIO_OUT_EN_OFFSET 0x08
>> +#define CYGNUS_GPIO_IN_TYPE_OFFSET 0x0c
>> +#define CYGNUS_GPIO_INT_DE_OFFSET 0x10
>> +#define CYGNUS_GPIO_INT_EDGE_OFFSET 0x14
>> +#define CYGNUS_GPIO_INT_MSK_OFFSET 0x18
>> +#define CYGNUS_GPIO_INT_STAT_OFFSET 0x1c
>> +#define CYGNUS_GPIO_INT_MSTAT_OFFSET 0x20
>> +#define CYGNUS_GPIO_INT_CLR_OFFSET 0x24
>> +#define CYGNUS_GPIO_PAD_RES_OFFSET 0x34
>> +#define CYGNUS_GPIO_RES_EN_OFFSET 0x38
>> +
>> +/* drive strength control for ASIU GPIO */
>> +#define CYGNUS_GPIO_ASIU_DRV0_CTRL_OFFSET 0x58
>> +
>> +/* drive strength control for CCM/CRMU (AON) GPIO */
>> +#define CYGNUS_GPIO_DRV0_CTRL_OFFSET 0x00
>> +
>> +#define GPIO_BANK_SIZE 0x200
>> +#define NGPIOS_PER_BANK 32
>> +#define GPIO_BANK(pin) ((pin) / NGPIOS_PER_BANK)
>> +
>> +#define CYGNUS_GPIO_REG(pin, reg) (GPIO_BANK(pin) * GPIO_BANK_SIZE + (reg))
>> +#define CYGNUS_GPIO_SHIFT(pin) ((pin) % NGPIOS_PER_BANK)
>> +
>> +#define GPIO_DRV_STRENGTH_BIT_SHIFT 20
>> +#define GPIO_DRV_STRENGTH_BITS 3
>> +#define GPIO_DRV_STRENGTH_BIT_MASK ((1 << GPIO_DRV_STRENGTH_BITS) - 1)
>> +
>> +/*
>> + * Cygnus GPIO core
>> + *
>> + * @dev: pointer to device
>> + * @base: I/O register base for Cygnus GPIO controller
>> + * @io_ctrl: I/O register base for certain type of Cygnus GPIO controller that
>> + * has the PINCONF support implemented outside of the GPIO block
>> + * @lock: lock to protect access to I/O registers
>> + * @gc: GPIO chip
>> + * @num_banks: number of GPIO banks, each bank supports up to 32 GPIOs
>> + * @pinmux_is_supported: flag to indicate this GPIO controller contains pins
>> + * that can be individually muxed to GPIO
>> + * @pctl: pointer to pinctrl_dev
>> + * @pctldesc: pinctrl descriptor
>> + * @pins: pointer to array of pins
>> + */
>> +struct cygnus_gpio {
>> + struct device *dev;
>> +
>> + void __iomem *base;
>> + void __iomem *io_ctrl;
>> +
>> + spinlock_t lock;
>> +
>> + struct gpio_chip gc;
>> + unsigned num_banks;
>> +
>> + int pinmux_is_supported;
>
> bool?
>
Yes. Will do.

>> +
>> + struct pinctrl_dev *pctl;
>> + struct pinctrl_desc pctldesc;
>> + struct pinctrl_pin_desc *pins;
>> +};
>> +
>> +static struct cygnus_gpio *to_cygnus_gpio(struct gpio_chip *gc)
>> +{
>> + return container_of(gc, struct cygnus_gpio, gc);
>> +}
>> +
>> +/*
>> + * Mapping from PINCONF pins to GPIO pins is 1-to-1
>> + */
>> +static unsigned cygnus_pin_to_gpio(unsigned pin)
>> +{
>> + return pin;
>> +}
>> +
>> +static u32 cygnus_readl(struct cygnus_gpio *chip, unsigned int offset)
>> +{
>> + return readl(chip->base + offset);
>> +}
>> +
>> +static void cygnus_writel(struct cygnus_gpio *chip, unsigned int offset,
>> + u32 val)
>> +{
>> + writel(val, chip->base + offset);
>> +}
>> +
>> +/**
>> + * cygnus_set_bit - set or clear one bit (corresponding to the GPIO pin) in a
>> + * Cygnus GPIO register
>> + *
>> + * @cygnus_gpio: Cygnus GPIO device
>> + * @reg: register offset
>> + * @gpio: GPIO pin
>> + * @set: set or clear. 1 - set; 0 -clear
>> + */
>> +static void cygnus_set_bit(struct cygnus_gpio *chip, unsigned int reg,
>> + unsigned gpio, int set)
>> +{
>> + unsigned int offset = CYGNUS_GPIO_REG(gpio, reg);
>> + unsigned int shift = CYGNUS_GPIO_SHIFT(gpio);
>> + u32 val;
>> +
>> + val = cygnus_readl(chip, offset);
>> + if (set)
>> + val |= BIT(shift);
>> + else
>> + val &= ~BIT(shift);
>> + cygnus_writel(chip, offset, val);
>> +}
>> +
>> +static int cygnus_get_bit(struct cygnus_gpio *chip, unsigned int reg,
>> + unsigned gpio)
>> +{
>> + unsigned int offset = CYGNUS_GPIO_REG(gpio, reg);
>> + unsigned int shift = CYGNUS_GPIO_SHIFT(gpio);
>> + u32 val;
>> +
>> + val = cygnus_readl(chip, offset) & BIT(shift);
>> + if (val)
>> + return 1;
>> + else
>> + return 0;
>> +}
>> +
>> +static void cygnus_gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
>> +{
>> + struct gpio_chip *gc = irq_desc_get_handler_data(desc);
>> + struct cygnus_gpio *chip = to_cygnus_gpio(gc);
>> + struct irq_chip *irq_chip = irq_desc_get_chip(desc);
>> + int i, bit;
>> +
>> + chained_irq_enter(irq_chip, desc);
>> +
>> + /* go through the entire GPIO banks and handle all interrupts */
>> + for (i = 0; i < chip->num_banks; i++) {
>> + unsigned long val = cygnus_readl(chip,
>> + (i * GPIO_BANK_SIZE) +
>> + CYGNUS_GPIO_INT_MSTAT_OFFSET);
>> +
>> + for_each_set_bit(bit, &val, NGPIOS_PER_BANK) {
>> + unsigned pin = NGPIOS_PER_BANK * i + bit;
>> + int child_irq = irq_find_mapping(gc->irqdomain, pin);
>> +
>> + /*
>> + * Clear the interrupt before invoking the
>> + * handler, so we do not leave any window
>> + */
>> + cygnus_writel(chip, (i * GPIO_BANK_SIZE) +
>> + CYGNUS_GPIO_INT_CLR_OFFSET, BIT(bit));
>> +
>> + generic_handle_irq(child_irq);
>> + }
>> + }
>> +
>> + chained_irq_exit(irq_chip, desc);
>> +}
>> +
>> +
>> +static void cygnus_gpio_irq_ack(struct irq_data *d)
>> +{
>> + struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
>> + struct cygnus_gpio *chip = to_cygnus_gpio(gc);
>> + unsigned gpio = d->hwirq;
>> + unsigned int offset = CYGNUS_GPIO_REG(gpio,
>> + CYGNUS_GPIO_INT_CLR_OFFSET);
>> + unsigned int shift = CYGNUS_GPIO_SHIFT(gpio);
>> + u32 val = BIT(shift);
>> +
>> + cygnus_writel(chip, offset, val);
>> +}
>> +
>> +/**
>> + * cygnus_gpio_irq_set_mask - mask/unmask a GPIO interrupt
>> + *
>> + * @d: IRQ chip data
>> + * @mask: mask/unmask GPIO interrupt. 0 - mask (disable); 1 - unmask (enable)
>> + */
>> +static void cygnus_gpio_irq_set_mask(struct irq_data *d, int mask)
>> +{
>> + struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
>> + struct cygnus_gpio *chip = to_cygnus_gpio(gc);
>> + unsigned gpio = d->hwirq;
>> +
>> + cygnus_set_bit(chip, CYGNUS_GPIO_INT_MSK_OFFSET, gpio, mask);
>> +}
>> +
>> +static void cygnus_gpio_irq_mask(struct irq_data *d)
>> +{
>> + struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
>> + struct cygnus_gpio *chip = to_cygnus_gpio(gc);
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&chip->lock, flags);
>> + cygnus_gpio_irq_set_mask(d, 0);
>> + spin_unlock_irqrestore(&chip->lock, flags);
>> +}
>> +
>> +static void cygnus_gpio_irq_unmask(struct irq_data *d)
>> +{
>> + struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
>> + struct cygnus_gpio *chip = to_cygnus_gpio(gc);
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&chip->lock, flags);
>> + cygnus_gpio_irq_set_mask(d, 1);
>> + spin_unlock_irqrestore(&chip->lock, flags);
>> +}
>> +
>> +static int cygnus_gpio_irq_set_type(struct irq_data *d, unsigned int type)
>> +{
>> + struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
>> + struct cygnus_gpio *chip = to_cygnus_gpio(gc);
>> + unsigned gpio = d->hwirq;
>> + int int_type = 0, dual_edge = 0, edge_lvl = 0;
>> + unsigned long flags;
>> +
>> + switch (type & IRQ_TYPE_SENSE_MASK) {
>> + case IRQ_TYPE_EDGE_RISING:
>> + edge_lvl = 1;
>> + break;
>> +
>> + case IRQ_TYPE_EDGE_FALLING:
>> + break;
>> +
>> + case IRQ_TYPE_EDGE_BOTH:
>> + dual_edge = 1;
>> + break;
>> +
>> + case IRQ_TYPE_LEVEL_HIGH:
>> + int_type = 1;
>> + edge_lvl = 1;
>> + break;
>> +
>> + case IRQ_TYPE_LEVEL_LOW:
>> + int_type = 1;
>> + break;
>> +
>> + default:
>> + dev_err(chip->dev, "invalid GPIO IRQ type 0x%x\n",
>> + type);
>> + return -EINVAL;
>> + }
>> +
>> + spin_lock_irqsave(&chip->lock, flags);
>> + cygnus_set_bit(chip, CYGNUS_GPIO_IN_TYPE_OFFSET, gpio, int_type);
>> + cygnus_set_bit(chip, CYGNUS_GPIO_INT_DE_OFFSET, gpio, dual_edge);
>> + cygnus_set_bit(chip, CYGNUS_GPIO_INT_EDGE_OFFSET, gpio,
>> + edge_lvl);
>> + spin_unlock_irqrestore(&chip->lock, flags);
>> +
>> + dev_dbg(chip->dev,
>> + "gpio:%u set int_type:%d dual_edge:%d edge_lvl:%d\n",
>> + gpio, int_type, dual_edge, edge_lvl);
>> +
>> + return 0;
>> +}
>> +
>> +static struct irq_chip cygnus_gpio_irq_chip = {
>> + .name = "bcm-cygnus-gpio",
>> + .irq_ack = cygnus_gpio_irq_ack,
>> + .irq_mask = cygnus_gpio_irq_mask,
>> + .irq_unmask = cygnus_gpio_irq_unmask,
>> + .irq_set_type = cygnus_gpio_irq_set_type,
>> +};
>> +
>> +/*
>> + * Request the Cygnus IOMUX pinmux controller to mux individual pins to GPIO
>> + */
>> +static int cygnus_gpio_request(struct gpio_chip *gc, unsigned offset)
>> +{
>> + struct cygnus_gpio *chip = to_cygnus_gpio(gc);
>> + unsigned gpio = gc->base + offset;
>> +
>> + /* not all Cygnus GPIO pins can be muxed individually */
>> + if (!chip->pinmux_is_supported)
>> + return 0;
>> +
>> + return pinctrl_request_gpio(gpio);
>> +}
>> +
>> +static void cygnus_gpio_free(struct gpio_chip *gc, unsigned offset)
>> +{
>> + struct cygnus_gpio *chip = to_cygnus_gpio(gc);
>> + unsigned gpio = gc->base + offset;
>> +
>> + if (!chip->pinmux_is_supported)
>> + return;
>> +
>> + pinctrl_free_gpio(gpio);
>> +}
>> +
>> +static int cygnus_gpio_direction_input(struct gpio_chip *gc, unsigned gpio)
>> +{
>> + struct cygnus_gpio *chip = to_cygnus_gpio(gc);
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&chip->lock, flags);
>> + cygnus_set_bit(chip, CYGNUS_GPIO_OUT_EN_OFFSET, gpio, 0);
>> + spin_unlock_irqrestore(&chip->lock, flags);
>> +
>> + dev_dbg(chip->dev, "gpio:%u set input\n", gpio);
>> +
>> + return 0;
>> +}
>> +
>> +static int cygnus_gpio_direction_output(struct gpio_chip *gc, unsigned gpio,
>> + int value)
>> +{
>> + struct cygnus_gpio *chip = to_cygnus_gpio(gc);
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&chip->lock, flags);
>> + cygnus_set_bit(chip, CYGNUS_GPIO_OUT_EN_OFFSET, gpio, 1);
>> + cygnus_set_bit(chip, CYGNUS_GPIO_DATA_OUT_OFFSET, gpio, value);
>> + spin_unlock_irqrestore(&chip->lock, flags);
>> +
>> + dev_dbg(chip->dev, "gpio:%u set output, value:%d\n", gpio, value);
>> +
>> + return 0;
>> +}
>> +
>> +static void cygnus_gpio_set(struct gpio_chip *gc, unsigned gpio, int value)
>> +{
>> + struct cygnus_gpio *chip = to_cygnus_gpio(gc);
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&chip->lock, flags);
>> + cygnus_set_bit(chip, CYGNUS_GPIO_DATA_OUT_OFFSET, gpio, value);
>> + spin_unlock_irqrestore(&chip->lock, flags);
>> +
>> + dev_dbg(chip->dev, "gpio:%u set, value:%d\n", gpio, value);
>> +}
>> +
>> +static int cygnus_gpio_get(struct gpio_chip *gc, unsigned gpio)
>> +{
>> + struct cygnus_gpio *chip = to_cygnus_gpio(gc);
>> + unsigned int offset = CYGNUS_GPIO_REG(gpio,
>> + CYGNUS_GPIO_DATA_IN_OFFSET);
>> + unsigned int shift = CYGNUS_GPIO_SHIFT(gpio);
>> +
>> + return !!(cygnus_readl(chip, offset) & BIT(shift));
>> +}
>> +
>> +static int cygnus_get_groups_count(struct pinctrl_dev *pctldev)
>> +{
>> + return 1;
>> +}
>> +
>> +/*
>> + * Only one group: "gpio_grp", since this local pinctrl device only performs
>> + * GPIO specific PINCONF configurations
>> + */
>> +static const char *cygnus_get_group_name(struct pinctrl_dev *pctldev,
>> + unsigned selector)
>> +{
>> +
>
> Extra blank line.
>
Thanks!

>> + return "gpio_grp";
>> +}
>> +
>> +static const struct pinctrl_ops cygnus_pctrl_ops = {
>> + .get_groups_count = cygnus_get_groups_count,
>> + .get_group_name = cygnus_get_group_name,
>> + .dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
>> + .dt_free_map = pinctrl_utils_dt_free_map,
>> +};
>> +
>> +static int cygnus_gpio_set_pull(struct cygnus_gpio *chip, unsigned gpio,
>> + int disable, int pull_up)
>> +{
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&chip->lock, flags);
>> +
>> + if (disable) {
>> + cygnus_set_bit(chip, CYGNUS_GPIO_RES_EN_OFFSET, gpio, 0);
>> + } else {
>> + cygnus_set_bit(chip, CYGNUS_GPIO_PAD_RES_OFFSET, gpio,
>> + pull_up);
>> + cygnus_set_bit(chip, CYGNUS_GPIO_RES_EN_OFFSET, gpio, 1);
>> + }
>> +
>> + spin_unlock_irqrestore(&chip->lock, flags);
>> +
>> + dev_dbg(chip->dev, "gpio:%u set pullup:%d\n", gpio, pull_up);
>> +
>> + return 0;
>> +}
>> +
>> +static void cygnus_gpio_get_pull(struct cygnus_gpio *chip, unsigned gpio,
>> + int *disable, int *pull_up)
>> +{
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&chip->lock, flags);
>> + *disable = !cygnus_get_bit(chip, CYGNUS_GPIO_RES_EN_OFFSET, gpio);
>> + *pull_up = cygnus_get_bit(chip, CYGNUS_GPIO_PAD_RES_OFFSET, gpio);
>> + spin_unlock_irqrestore(&chip->lock, flags);
>> +}
>> +
>> +static int cygnus_gpio_set_strength(struct cygnus_gpio *chip, unsigned gpio,
>> + unsigned strength)
>> +{
>> + void __iomem *base;
>> + unsigned int i, offset, shift;
>> + u32 val;
>> + unsigned long flags;
>> +
>> + /* make sure drive strength is supported */
>> + if (strength < 2 || strength > 16 || (strength % 2))
>> + return -ENOTSUPP;
>> +
>> + if (chip->io_ctrl) {
>> + base = chip->io_ctrl;
>> + offset = CYGNUS_GPIO_DRV0_CTRL_OFFSET;
>> + } else {
>> + base = chip->base;
>> + offset = CYGNUS_GPIO_REG(gpio,
>> + CYGNUS_GPIO_ASIU_DRV0_CTRL_OFFSET);
>> + }
>> +
>> + shift = CYGNUS_GPIO_SHIFT(gpio);
>> +
>> + dev_dbg(chip->dev, "gpio:%u set drive strength:%d mA\n", gpio,
>> + strength);
>> +
>> + spin_lock_irqsave(&chip->lock, flags);
>> + strength = (strength / 2) - 1;
>> + for (i = 0; i < GPIO_DRV_STRENGTH_BITS; i++) {
>> + val = readl(base + offset);
>> + val &= ~BIT(shift);
>> + val |= ((strength >> i) & 0x1) << shift;
>> + writel(val, base + offset);
>> + offset += 4;
>> + }
>> + spin_unlock_irqrestore(&chip->lock, flags);
>> +
>> + return 0;
>> +}
>> +
>> +static int cygnus_gpio_get_strength(struct cygnus_gpio *chip, unsigned gpio,
>> + u16 *strength)
>> +{
>> + void __iomem *base;
>> + unsigned int i, offset, shift;
>> + u32 val;
>> + unsigned long flags;
>> +
>> + if (chip->io_ctrl) {
>> + base = chip->io_ctrl;
>> + offset = CYGNUS_GPIO_DRV0_CTRL_OFFSET;
>> + } else {
>> + base = chip->base;
>> + offset = CYGNUS_GPIO_REG(gpio,
>> + CYGNUS_GPIO_ASIU_DRV0_CTRL_OFFSET);
>> + }
>> +
>> + shift = CYGNUS_GPIO_SHIFT(gpio);
>> +
>> + spin_lock_irqsave(&chip->lock, flags);
>> + *strength = 0;
>> + for (i = 0; i < GPIO_DRV_STRENGTH_BITS; i++) {
>> + val = readl(base + offset) & BIT(shift);
>> + val >>= shift;
>> + *strength += (val << i);
>> + offset += 4;
>> + }
>> +
>> + /* convert to mA */
>> + *strength = (*strength + 1) * 2;
>> + spin_unlock_irqrestore(&chip->lock, flags);
>> +
>> + return 0;
>> +}
>> +
>> +static int cygnus_pin_config_get(struct pinctrl_dev *pctldev, unsigned pin,
>> + unsigned long *config)
>> +{
>> + struct cygnus_gpio *chip = pinctrl_dev_get_drvdata(pctldev);
>> + enum pin_config_param param = pinconf_to_config_param(*config);
>> + unsigned gpio = cygnus_pin_to_gpio(pin);
>> + u16 arg;
>> + int disable, pull_up, ret;
>> +
>> + switch (param) {
>> + case PIN_CONFIG_BIAS_DISABLE:
>> + cygnus_gpio_get_pull(chip, gpio, &disable, &pull_up);
>> + if (disable)
>> + return 0;
>> + else
>> + return -EINVAL;
>> +
>> + case PIN_CONFIG_BIAS_PULL_UP:
>> + cygnus_gpio_get_pull(chip, gpio, &disable, &pull_up);
>> + if (!disable && pull_up)
>> + return 0;
>> + else
>> + return -EINVAL;
>> +
>> + case PIN_CONFIG_BIAS_PULL_DOWN:
>> + cygnus_gpio_get_pull(chip, gpio, &disable, &pull_up);
>> + if (!disable && !pull_up)
>> + return 0;
>> + else
>> + return -EINVAL;
>> +
>> + case PIN_CONFIG_DRIVE_STRENGTH:
>> + ret = cygnus_gpio_get_strength(chip, gpio, &arg);
>> + if (ret)
>> + return ret;
>> + else
>> + *config = pinconf_to_config_packed(param, arg);
>> +
>> + return 0;
>> +
>> + default:
>> + return -ENOTSUPP;
>> + }
>> +
>> + return -ENOTSUPP;
>> +}
>> +
>> +static int cygnus_pin_config_set(struct pinctrl_dev *pctldev, unsigned pin,
>> + unsigned long *configs, unsigned num_configs)
>> +{
>> + struct cygnus_gpio *chip = pinctrl_dev_get_drvdata(pctldev);
>> + enum pin_config_param param;
>> + u16 arg;
>> + unsigned i, gpio = cygnus_pin_to_gpio(pin);
>> + int ret = -ENOTSUPP;
>> +
>> + for (i = 0; i < num_configs; i++) {
>> + param = pinconf_to_config_param(configs[i]);
>> + arg = pinconf_to_config_argument(configs[i]);
>> +
>> + switch (param) {
>> + case PIN_CONFIG_BIAS_DISABLE:
>> + ret = cygnus_gpio_set_pull(chip, gpio, 1, 0);
>> + if (ret < 0)
>> + goto out;
>> + break;
>> +
>> + case PIN_CONFIG_BIAS_PULL_UP:
>> + ret = cygnus_gpio_set_pull(chip, gpio, 0, 1);
>> + if (ret < 0)
>> + goto out;
>> + break;
>> +
>> + case PIN_CONFIG_BIAS_PULL_DOWN:
>> + ret = cygnus_gpio_set_pull(chip, gpio, 0, 0);
>> + if (ret < 0)
>> + goto out;
>> + break;
>> +
>> + case PIN_CONFIG_DRIVE_STRENGTH:
>> + ret = cygnus_gpio_set_strength(chip, gpio, arg);
>> + if (ret < 0)
>> + goto out;
>> + break;
>> +
>> + default:
>> + dev_err(chip->dev, "invalid configuration\n");
>> + return -ENOTSUPP;
>> + }
>> + } /* for each config */
>> +
>> +out:
>> + return ret;
>> +}
>> +
>> +static const struct pinconf_ops cygnus_pconf_ops = {
>> + .is_generic = true,
>> + .pin_config_get = cygnus_pin_config_get,
>> + .pin_config_set = cygnus_pin_config_set,
>> +};
>> +
>> +/*
>> + * Map a GPIO in the local gpio_chip pin space to a pin in the Cygnus IOMUX
>> + * pinctrl pin space
>> + */
>> +struct cygnus_gpio_pin_range {
>> + unsigned offset;
>> + unsigned pin_base;
>> + unsigned num_pins;
>> +};
>> +
>> +#define CYGNUS_PINRANGE(o, p, n) { .offset = o, .pin_base = p, .num_pins = n }
>> +
>> +/*
>> + * Pin mapping table for mapping local GPIO pins to Cygnus IOMUX pinctrl pins
>> + */
>> +static const struct cygnus_gpio_pin_range cygnus_gpio_pintable[] = {
>> + CYGNUS_PINRANGE(0, 42, 1),
>> + CYGNUS_PINRANGE(1, 44, 3),
>> + CYGNUS_PINRANGE(4, 48, 1),
>> + CYGNUS_PINRANGE(5, 50, 3),
>> + CYGNUS_PINRANGE(8, 126, 1),
>> + CYGNUS_PINRANGE(9, 155, 1),
>> + CYGNUS_PINRANGE(10, 152, 1),
>> + CYGNUS_PINRANGE(11, 154, 1),
>> + CYGNUS_PINRANGE(12, 153, 1),
>> + CYGNUS_PINRANGE(13, 127, 3),
>> + CYGNUS_PINRANGE(16, 140, 1),
>> + CYGNUS_PINRANGE(17, 145, 7),
>> + CYGNUS_PINRANGE(24, 130, 10),
>> + CYGNUS_PINRANGE(34, 141, 4),
>> + CYGNUS_PINRANGE(38, 54, 1),
>> + CYGNUS_PINRANGE(39, 56, 3),
>> + CYGNUS_PINRANGE(42, 60, 3),
>> + CYGNUS_PINRANGE(45, 64, 3),
>> + CYGNUS_PINRANGE(48, 68, 2),
>> + CYGNUS_PINRANGE(50, 84, 6),
>> + CYGNUS_PINRANGE(56, 94, 6),
>> + CYGNUS_PINRANGE(62, 72, 1),
>> + CYGNUS_PINRANGE(63, 70, 1),
>> + CYGNUS_PINRANGE(64, 80, 1),
>> + CYGNUS_PINRANGE(65, 74, 3),
>> + CYGNUS_PINRANGE(68, 78, 1),
>> + CYGNUS_PINRANGE(69, 82, 1),
>> + CYGNUS_PINRANGE(70, 156, 17),
>> + CYGNUS_PINRANGE(87, 104, 12),
>> + CYGNUS_PINRANGE(99, 102, 2),
>> + CYGNUS_PINRANGE(101, 90, 4),
>> + CYGNUS_PINRANGE(105, 116, 10),
>> + CYGNUS_PINRANGE(123, 11, 1),
>> + CYGNUS_PINRANGE(124, 38, 4),
>> + CYGNUS_PINRANGE(128, 43, 1),
>> + CYGNUS_PINRANGE(129, 47, 1),
>> + CYGNUS_PINRANGE(130, 49, 1),
>> + CYGNUS_PINRANGE(131, 53, 1),
>> + CYGNUS_PINRANGE(132, 55, 1),
>> + CYGNUS_PINRANGE(133, 59, 1),
>> + CYGNUS_PINRANGE(134, 63, 1),
>> + CYGNUS_PINRANGE(135, 67, 1),
>> + CYGNUS_PINRANGE(136, 71, 1),
>> + CYGNUS_PINRANGE(137, 73, 1),
>> + CYGNUS_PINRANGE(138, 77, 1),
>> + CYGNUS_PINRANGE(139, 79, 1),
>> + CYGNUS_PINRANGE(140, 81, 1),
>> + CYGNUS_PINRANGE(141, 83, 1),
>> + CYGNUS_PINRANGE(142, 10, 1)
>> +};
>> +
>> +/*
>> + * The Cygnus IOMUX controller mainly supports group based mux configuration,
>> + * but certain pins can be muxed to GPIO individually. Only the ASIU GPIO
>> + * controller can support this, so it's an optional configuration
>> + *
>> + * Return -ENODEV means no support and that's fine
>> + */
>> +static int cygnus_gpio_pinmux_add_range(struct cygnus_gpio *chip)
>> +{
>> + struct device_node *node = chip->dev->of_node;
>> + struct device_node *pinmux_node;
>> + struct platform_device *pinmux_pdev;
>> + struct gpio_chip *gc = &chip->gc;
>> + int i, ret;
>> +
>> + /* parse DT to find the phandle to the pinmux controller */
>> + pinmux_node = of_parse_phandle(node, "pinmux", 0);
>> + if (!pinmux_node)
>> + return -ENODEV;
>> +
>> + pinmux_pdev = of_find_device_by_node(pinmux_node);
>> + if (!pinmux_pdev) {
>> + dev_err(chip->dev, "failed to get pinmux device\n");
>> + return -EINVAL;
>> + }
>> +
>> + /* now need to create the mapping between local GPIO and PINMUX pins */
>> + for (i = 0; i < ARRAY_SIZE(cygnus_gpio_pintable); i++) {
>> + ret = gpiochip_add_pin_range(gc, dev_name(&pinmux_pdev->dev),
>> + cygnus_gpio_pintable[i].offset,
>> + cygnus_gpio_pintable[i].pin_base,
>> + cygnus_gpio_pintable[i].num_pins);
>> + if (ret) {
>> + dev_err(chip->dev, "unable to add GPIO pin range\n");
>> + goto err_rm_pin_range;
>> + }
>> + }
>> +
>> + chip->pinmux_is_supported = 1;
>
> chip->pinmux_is_supported = true;
>
> ?
>
>> + return 0;
>> +
>> +err_rm_pin_range:
>> + gpiochip_remove_pin_ranges(gc);
>
> I think you need:
>
> put_dveice(&pinmux_pdev->dev);
>
> since of_find_device_by_node calls bus_find_device() that takes
> reference to found device.
>
> ... And now that I look at this majority of users of
> of_find_device_by_node() is broken like that :(
>
> BTW, it looks like you only need pinmux_dev for it's name so you
> probably need to drop reference in success path as well.
>
Oh wow! Really good to know. Will fix!

>> + return ret;
>> +}
>> +
>> +static void cygnus_gpio_pinmux_remove_range(struct cygnus_gpio *chip)
>> +{
>> + struct gpio_chip *gc = &chip->gc;
>> +
>> + if (chip->pinmux_is_supported)
>> + gpiochip_remove_pin_ranges(gc);
>> +}
>> +
>> +/*
>> + * Cygnus GPIO controller supports some PINCONF related configurations such as
>> + * pull up, pull down, and drive strength, when the pin is configured to GPIO
>> + *
>> + * Here a local pinctrl device is created with simple 1-to-1 pin mapping to the
>> + * local GPIO pins
>> + */
>> +static int cygnus_gpio_register_pinconf(struct cygnus_gpio *chip)
>> +{
>> + struct pinctrl_desc *pctldesc = &chip->pctldesc;
>> + struct pinctrl_pin_desc *pins;
>> + struct gpio_chip *gc = &chip->gc;
>> + int i, ret;
>> +
>> + pins = devm_kcalloc(chip->dev, gc->ngpio, sizeof(*pins), GFP_KERNEL);
>> + if (!pins)
>> + return -ENOMEM;
>> + chip->pins = pins;
>> +
>> + for (i = 0; i < gc->ngpio; i++) {
>> + pins[i].number = i;
>> + pins[i].name = kasprintf(GFP_KERNEL, "gpio-%d", i);
>
> We have devm_kasprintf().
>
I was not aware of that. Okay I'll change to devm_kasprintf so I can get
rid of some memory free code below. Thanks!

>> + if (!pins[i].name) {
>> + ret = -ENOMEM;
>> + goto err_kfree;
>> + }
>> + }
>> +
>> + pctldesc->name = dev_name(chip->dev);
>> + pctldesc->pctlops = &cygnus_pctrl_ops;
>> + pctldesc->pins = pins;
>> + pctldesc->npins = gc->ngpio;
>> + pctldesc->confops = &cygnus_pconf_ops;
>> +
>> + chip->pctl = pinctrl_register(pctldesc, chip->dev, chip);
>> + if (!chip->pctl) {
>> + dev_err(chip->dev, "unable to register pinctrl device\n");
>> + ret = -EINVAL;
>> + goto err_kfree;
>> + }
>> +
>> + return 0;
>> +
>> +err_kfree:
>> + for (i = 0; i < gc->ngpio; i++)
>> + kfree(pins[i].name);
>> +
>> + return ret;
>> +}
>> +
>> +static void cygnus_gpio_unregister_pinconf(struct cygnus_gpio *chip)
>> +{
>> + struct gpio_chip *gc = &chip->gc;
>> + int i;
>> +
>> + if (chip->pctl)
>> + pinctrl_unregister(chip->pctl);
>> +
>> + for (i = 0; i < gc->ngpio; i++)
>> + kfree(chip->pins[i].name);
>
> Should not be needed if you use devm_kasprintf.
>
Yes!

>> +}
>> +
>> +static const struct of_device_id cygnus_gpio_of_match[] = {
>> + { .compatible = "brcm,cygnus-gpio" },
>> + { }
>> +};
>> +MODULE_DEVICE_TABLE(of, cygnus_gpio_of_match);
>> +
>> +static int cygnus_gpio_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct resource *res;
>> + struct cygnus_gpio *chip;
>> + struct gpio_chip *gc;
>> + u32 ngpios;
>> + int irq, ret;
>> +
>> + chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL);
>> + if (!chip)
>> + return -ENOMEM;
>> +
>> + chip->dev = dev;
>> + platform_set_drvdata(pdev, chip);
>> +
>> + if (of_property_read_u32(dev->of_node, "ngpios", &ngpios)) {
>> + dev_err(dev, "missing ngpios DT property\n");
>> + return -ENODEV;
>> + }
>> + chip->num_banks = (ngpios + NGPIOS_PER_BANK - 1) / NGPIOS_PER_BANK;
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + chip->base = devm_ioremap_resource(dev, res);
>> + if (IS_ERR(chip->base)) {
>> + dev_err(dev, "unable to map I/O memory\n");
>> + return PTR_ERR(chip->base);
>> + }
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
>> + if (res) {
>> + chip->io_ctrl = devm_ioremap_resource(dev, res);
>> + if (IS_ERR(chip->io_ctrl)) {
>> + dev_err(dev, "unable to map I/O memory\n");
>> + return PTR_ERR(chip->io_ctrl);
>> + }
>> + }
>> +
>> + spin_lock_init(&chip->lock);
>> +
>> + gc = &chip->gc;
>> + gc->base = -1;
>> + gc->ngpio = ngpios;
>> + gc->label = dev_name(dev);
>> + gc->dev = dev;
>> + gc->of_node = dev->of_node;
>> + gc->request = cygnus_gpio_request;
>> + gc->free = cygnus_gpio_free;
>> + gc->direction_input = cygnus_gpio_direction_input;
>> + gc->direction_output = cygnus_gpio_direction_output;
>> + gc->set = cygnus_gpio_set;
>> + gc->get = cygnus_gpio_get;
>> +
>> + ret = gpiochip_add(gc);
>> + if (ret < 0) {
>> + dev_err(dev, "unable to add GPIO chip\n");
>> + return ret;
>> + }
>> +
>> + ret = cygnus_gpio_pinmux_add_range(chip);
>> + if (ret && ret != -ENODEV) {
>> + dev_err(dev, "unable to add GPIO pin range\n");
>> + goto err_rm_gpiochip;
>> + }
>> +
>> + ret = cygnus_gpio_register_pinconf(chip);
>> + if (ret) {
>> + dev_err(dev, "unable to register pinconf\n");
>> + goto err_rm_range;
>> + }
>> +
>> + /* optional GPIO interrupt support */
>> + irq = platform_get_irq(pdev, 0);
>> + if (irq) {
>> + ret = gpiochip_irqchip_add(gc, &cygnus_gpio_irq_chip, 0,
>> + handle_simple_irq, IRQ_TYPE_NONE);
>> + if (ret) {
>> + dev_err(dev, "no GPIO irqchip\n");
>> + goto err_unregister_pinconf;
>> + }
>> +
>> + gpiochip_set_chained_irqchip(gc, &cygnus_gpio_irq_chip, irq,
>> + cygnus_gpio_irq_handler);
>> + }
>> +
>> + return 0;
>> +
>> +err_unregister_pinconf:
>> + cygnus_gpio_unregister_pinconf(chip);
>> +
>> +err_rm_range:
>> + cygnus_gpio_pinmux_remove_range(chip);
>> +
>> +err_rm_gpiochip:
>> + gpiochip_remove(gc);
>> +
>> + return ret;
>> +}
>> +
>> +static struct platform_driver cygnus_gpio_driver = {
>> + .driver = {
>> + .name = "cygnus-gpio",
>> + .of_match_table = cygnus_gpio_of_match,
>> + },
>> + .probe = cygnus_gpio_probe,
>
> The same comment about suppress_bind_attrs.
>
Okay. Will do!

>> +};
>> +
>> +static int __init cygnus_gpio_init(void)
>> +{
>> + return platform_driver_probe(&cygnus_gpio_driver, cygnus_gpio_probe);
>> +}
>> +arch_initcall_sync(cygnus_gpio_init);
>> +
>> +MODULE_AUTHOR("Ray Jui <rjui@xxxxxxxxxxxx>");
>> +MODULE_DESCRIPTION("Broadcom Cygnus GPIO Driver");
>> +MODULE_LICENSE("GPL v2");
>> --
>> 1.7.9.5
>>
>
> Thanks.
>
Thanks for the review, Dmitry!

Ray
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/