[PATCH/RFC v12 13/19] DT: Add documentation for the Skyworks AAT1290

[Jacek Anaszewski]

This patch adds device tree binding documentation for
1.5A Step-Up Current Regulator for Flash LEDs.

Signed-off-by: Jacek Anaszewski <j.anaszewski@xxxxxxxxxxx>
Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
Cc: Bryan Wu <cooloney@xxxxxxxxx>
Cc: Richard Purdie <rpurdie@xxxxxxxxx>
---
 .../devicetree/bindings/leds/leds-aat1290.txt      |   64 ++++++++++++++++++++
 1 file changed, 64 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/leds-aat1290.txt

diff --git a/Documentation/devicetree/bindings/leds/leds-aat1290.txt b/Documentation/devicetree/bindings/leds/leds-aat1290.txt
new file mode 100644
index 0000000..4f3583d
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/leds-aat1290.txt
@@ -0,0 +1,64 @@
+* Skyworks Solutions, Inc. AAT1290 Current Regulator for Flash LEDs
+
+The device is controlled through two pins: FL_EN and EN_SET. The pins when,
+asserted high, enable flash strobe and movie mode (max 1/2 of flash current)
+respectively. In order to add a capability of selecting the strobe signal source
+(e.g. GPIO or ISP) there is an additional switch required, independent of the
+flash chip.
+
+Required properties:
+
+- compatible : Must be "skyworks,aat1290".
+- gpios : Two gpio pins in order FLEN, EN/SET
+
+Optional properties:
+- pinctrl-names : Must contain entries: "default", "host", "isp". Entries
+		"default" and "host" must refer to the same pin configration
+		node, which sets the strobe signal source to host. Entry "isp"
+		must refer to the pin configuration node, which sets the strobe
+		signal source to ISP.
+
+The LED connected to the device must be represented by a child node -
+see Documentation/devicetree/bindings/leds/common.txt.
+
+Required properties of the LED child node:
+- label : see Documentation/devicetree/bindings/leds/common.txt
+- flash-max-microamp : Maximum intensity in microamperes of the flash LED -
+		       it can be calculated using following formula:
+		       I = 1A * 162kohm / Rset
+- flash-timeout-us : Maximum flash timeout in microseconds -
+		     it can be calculated using following formula:
+		     T = 8.82 * 10^9 * Ct.
+
+Example (by Ct = 220nF, Rset = 160kohm and exynos4412-trats2 board with a
+switch that allows for routing the strobe source signal either from host or
+from ISP):
+
+aat1290 {
+	compatible = "skyworks,aat1290";
+	gpios = <&gpj1 1 0>, <&gpj1 2 0>;
+	pinctrl-names = "default", "host", "isp";
+	pinctrl-0 = <&camera_flash_host>;
+	pinctrl-1 = <&camera_flash_host>;
+	pinctrl-2 = <&camera_flash_isp>;
+
+	camera_flash: flash-led {
+		label = "aat1290-flash";
+		flash-max-microamp = <1012500>
+		flash-timeout-us = <1940000>;
+	};
+};
+
+&pinctrl_0 {
+	camera_flash_host: camera-flash-host {
+		samsung,pins = "gpj1-0";
+		samsung,pin-function = <1>;
+		samsung,pin-val = <0>;
+	};
+
+	camera_flash_isp: camera-flash-isp {
+		samsung,pins = "gpj1-0";
+		samsung,pin-function = <1>;
+		samsung,pin-val = <1>;
+	};
+};
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/