[PATCH v5 1/4] mtd: nand: increase ready wait timeout and report timeouts

[Alex Smith]

If nand_wait_ready() times out, this is silently ignored, and its
caller will then proceed to read from/write to the chip before it is
ready. This can potentially result in corruption with no indication as
to why.

While a 20ms timeout seems like it should be plenty enough, certain
behaviour can cause it to timeout much earlier than expected. The
situation which prompted this change was that CPU 0, which is
responsible for updating jiffies, was holding interrupts disabled
for a fairly long time while writing to the console during a printk,
causing several jiffies updates to be delayed. If CPU 1 happens to
enter the timeout loop in nand_wait_ready() just before CPU 0 re-
enables interrupts and updates jiffies, CPU 1 will immediately time
out when the delayed jiffies updates are made. The result of this is
that nand_wait_ready() actually waits less time than the NAND chip
would normally take to be ready, and then read_page() proceeds to
read out bad data from the chip.

The situation described above may seem unlikely, but in fact it can be
reproduced almost every boot on the MIPS Creator Ci20.

Debugging this was made more difficult by the misleading comment above
nand_wait_ready() stating "The timeout is caught later" - no timeout
was ever reported, leading me away from the real source of the problem.

Therefore, this patch increases the timeout to 200ms. This should be
enough to cover cases where jiffies updates get delayed. Additionally,
add a pr_warn() when a timeout does occur so that it is easier to
pinpoint any problems in future caused by the chip not becoming ready.

Signed-off-by: Alex Smith <alex.smith@xxxxxxxxxx>
Reviewed-by: Ezequiel Garcia <ezequiel@xxxxxxxxxxxxxxxxxxxx>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@xxxxxxxxxx>
Cc: David Woodhouse <dwmw2@xxxxxxxxxxxxx>
Cc: Brian Norris <computersforpeace@xxxxxxxxx>
Cc: linux-mtd@xxxxxxxxxxxxxxxxxxx
Cc: linux-kernel@xxxxxxxxxxxxxxx
---
v4 -> v5:
 - Remove spurious change.
 - Add Ezequiel's Reviewed-by.

v3 -> v4:
 - New patch to fix issue encountered in external Ci20 3.18 kernel
   branch which also applies upstream.
---
 drivers/mtd/nand/nand_base.c | 14 +++++++++++---
 1 file changed, 11 insertions(+), 3 deletions(-)

diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index ceb68ca8277a..07b831b94e5c 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -543,11 +543,16 @@ static void panic_nand_wait_ready(struct mtd_info *mtd, unsigned long timeo)
 	}
 }
 
-/* Wait for the ready pin, after a command. The timeout is caught later. */
+/**
+ * nand_wait_ready - [GENERIC] Wait for the ready pin after commands.
+ * @mtd: MTD device structure
+ *
+ * Wait for the ready pin after a command, and warn if a timeout occurs.
+ */
 void nand_wait_ready(struct mtd_info *mtd)
 {
 	struct nand_chip *chip = mtd->priv;
-	unsigned long timeo = jiffies + msecs_to_jiffies(20);
+	unsigned long timeo = jiffies + msecs_to_jiffies(200);
 
 	/* 400ms timeout */
 	if (in_interrupt() || oops_in_progress)
@@ -557,9 +562,12 @@ void nand_wait_ready(struct mtd_info *mtd)
 	/* Wait until command is processed or timeout occurs */
 	do {
 		if (chip->dev_ready(mtd))
-			break;
+			goto out;
 		touch_softlockup_watchdog();
 	} while (time_before(jiffies, timeo));
+
+	pr_warn("timeout while waiting for chip to become ready\n");
+out:
 	led_trigger_event(nand_led_trigger, LED_OFF);
 }
 EXPORT_SYMBOL_GPL(nand_wait_ready);
-- 
2.5.0

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/