Re: [PATCH 1/2] mmc: dw_mmc: add hw_reset support

[Jaehoon Chung]

Hi, Shawn.

On 10/22/2015 03:19 PM, Shawn Lin wrote:
> This patch implement hw_reset function for DesignWare
> MMC controller. By adding this feature, mmc blk can
> do some basic recovery if emmc device cannot work any
> more for unknown reasons.

Are there any other issue before applied this patch?

> 
> Signed-off-by: Shawn Lin <shawn.lin@xxxxxxxxxxxxxx>
> 
> ---
> 
>  drivers/mmc/host/dw_mmc.c | 29 +++++++++++++++++++++++++++++
>  drivers/mmc/host/dw_mmc.h |  4 ++++
>  2 files changed, 33 insertions(+)
> 
> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
> index 6e600e8..8a0f2995 100644
> --- a/drivers/mmc/host/dw_mmc.c
> +++ b/drivers/mmc/host/dw_mmc.c
> @@ -1478,6 +1478,34 @@ static int dw_mci_get_cd(struct mmc_host *mmc)
>  	return present;
>  }
>  
> +static void dw_mci_hw_reset(struct mmc_host *mmc)
> +{
> +	struct dw_mci_slot *slot = mmc_priv(mmc);
> +	struct dw_mci *host = slot->host;
> +
> +	if (host->use_dma == TRANS_MODE_IDMAC)
> +		dw_mci_idmac_reset(host);
> +
> +	if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_DMA_RESET) ||
> +	    (!dw_mci_ctrl_reset(host, SDMMC_CTRL_FIFO_RESET)))

Why does it reset twice? Can't reset together with DMA and FIFO?
dw_mci_ctrl_reset(host, SDMMC_CTRL_DMA_RESET | SDMMC_CTRL_FIFO_RESET)?

> +		return;
> +
> +	/* CARD_RESET
> +	 * According to eMMC spec
> +	 * tRstW >= 1us:   RST_n pulse width
> +	 * tRSCA >= 200us: RST_n to Command time
> +	 * tRSTH >= 1us:   RST_n high period
> +	 * Note: add some margin to make rst timing not too
> +	 * "spec" for some bad qulity eMMC devices.

some bad quality? Which devices are bad quality devices?

> +	 */
> +	 mci_writel(slot->host, RST_N, SDMMC_RST_HWRESET);
> +	 wmb(); /* drain writebuffer */
> +	 usleep_range(5, 10);
> +	 mci_writel(slot->host, RST_N, SDMMC_RST_HWACTIVE);
> +	 wmb(); /* drain writebuffer */
> +	 usleep_range(500, 1000);

Need to drain writebuffer at here?
I don't know why you choose those values..Just some margin?
And if you want to apply this, i recommend to use the shift with card number.

Best Regards,
Jaehoon Chung

> +}
> +
>  static void dw_mci_init_card(struct mmc_host *mmc, struct mmc_card *card)
>  {
>  	struct dw_mci_slot *slot = mmc_priv(mmc);
> @@ -1564,6 +1592,7 @@ static const struct mmc_host_ops dw_mci_ops = {
>  	.set_ios		= dw_mci_set_ios,
>  	.get_ro			= dw_mci_get_ro,
>  	.get_cd			= dw_mci_get_cd,
> +	.hw_reset               = dw_mci_hw_reset,
>  	.enable_sdio_irq	= dw_mci_enable_sdio_irq,
>  	.execute_tuning		= dw_mci_execute_tuning,
>  	.card_busy		= dw_mci_card_busy,
> diff --git a/drivers/mmc/host/dw_mmc.h b/drivers/mmc/host/dw_mmc.h
> index f2a88d4..9df18c1 100644
> --- a/drivers/mmc/host/dw_mmc.h
> +++ b/drivers/mmc/host/dw_mmc.h
> @@ -46,6 +46,7 @@
>  #define SDMMC_VERID		0x06c
>  #define SDMMC_HCON		0x070
>  #define SDMMC_UHS_REG		0x074
> +#define SDMMC_RST_N		0x078
>  #define SDMMC_BMOD		0x080
>  #define SDMMC_PLDMND		0x084
>  #define SDMMC_DBADDR		0x088
> @@ -169,6 +170,9 @@
>  #define SDMMC_IDMAC_ENABLE		BIT(7)
>  #define SDMMC_IDMAC_FB			BIT(1)
>  #define SDMMC_IDMAC_SWRESET		BIT(0)
> +/* H/W reset*/
> +#define SDMMC_RST_HWACTIVE		0x1
> +#define SDMMC_RST_HWRESET		0x0
>  /* Version ID register define */
>  #define SDMMC_GET_VERID(x)		((x) & 0xFFFF)
>  /* Card read threshold */
> 

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/