[PATCH 1/2] MIPS: bmips: Add bcm63168-l1 interrupt controller

From: Simon Arlott
Date: Sun Nov 15 2015 - 11:52:22 EST


Add device tree binding for the BCM63168 interrupt controller.

This controller is similar to the SMP-capable BCM7038 and
the BCM3380 but with packed interrupt registers.

Signed-off-by: Simon Arlott <simon@xxxxxxxxxxx>
---
.../interrupt-controller/brcm,bcm63168-l1-intc.txt | 57 ++++++++++++++++++++++
1 file changed, 57 insertions(+)
create mode 100644 Documentation/devicetree/bindings/interrupt-controller/brcm,bcm63168-l1-intc.txt

diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm63168-l1-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm63168-l1-intc.txt
new file mode 100644
index 0000000..636a6db
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm63168-l1-intc.txt
@@ -0,0 +1,57 @@
+Broadcom BCM63168-style Level 1 interrupt controller
+
+This block is a first level interrupt controller that is typically connected
+directly to one of the HW INT lines on each CPU.
+
+Key elements of the hardware design include:
+
+- 64 or 128 incoming level IRQ lines
+
+- Most onchip peripherals are wired directly to an L1 input
+
+- A separate instance of the register set for each CPU, allowing individual
+ peripheral IRQs to be routed to any CPU
+
+- Contains one or more enable/status word pairs per CPU
+
+- No atomic set/clear operations
+
+- No polarity/level/edge settings
+
+- No FIFO or priority encoder logic; software is expected to read all
+ 2-4 status words to determine which IRQs are pending
+
+Required properties:
+
+- compatible: should be "brcm,bcm63168-l1-intc"
+- reg: specifies the base physical address and size of the registers;
+ the number of supported IRQs is inferred from the size argument
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: specifies the number of cells needed to encode an interrupt
+ source, should be 1.
+- interrupt-parent: specifies the phandle to the parent interrupt controller(s)
+ this one is cascaded from
+- interrupts: specifies the interrupt line(s) in the interrupt-parent controller
+ node; valid values depend on the type of parent interrupt controller
+
+If multiple reg ranges and interrupt-parent entries are present on an SMP
+system, the driver will allow IRQ SMP affinity to be set up through the
+/proc/irq/ interface. In the simplest possible configuration, only one
+reg range and one interrupt-parent is needed.
+
+The driver operates in native CPU endian by default, there is no support for
+specifying an alternative endianness.
+
+Example:
+
+periph_intc: periph_intc@10000000 {
+ compatible = "brcm,bcm63168-l1-intc";
+ reg = <0x10000020 0x20>,
+ <0x10000040 0x20>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&cpu_intc>;
+ interrupts = <2>, <3>;
+};
--
2.1.4

--
Simon Arlott
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/