Re: [PATCHv2 16/16] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules

From: Shawn Guo
Date: Sun Feb 28 2016 - 01:45:09 EST

On Wed, Jan 20, 2016 at 11:09:09AM +0100, Lothar Waßmann wrote:
> The TXUL-0010/-0011 modules are Computers On Module manufactured by
> Ka-Ro electronics GmbH with the following characteristics:
> Processor Freescale i.MX 6UltraLite MCIMX6G2, 528 MHz
> RAM 256MB 16-bit DDR3 SDRAM
> ROM 128MB NAND Flash (TXUL-0010) / 4GB eMMC (TXUL-0011)
> Power supply Single 3.3 to 5V
> Size 26mm SO-DIMM
> Temp. Range -40°C to 85°C
>
>
> Signed-off-by: Lothar Waßmann <LW@xxxxxxxxxxxxxxxxxxx>
> ---
> arch/arm/boot/dts/Makefile | 4 +-
> arch/arm/boot/dts/imx6ul-txul-0010.dts | 54 ++
> arch/arm/boot/dts/imx6ul-txul-0011.dts | 85 +++
> arch/arm/boot/dts/imx6ul-txul.dtsi | 962 +++++++++++++++++++++++++++++++++
> 4 files changed, 1104 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/imx6ul-txul-0010.dts
> create mode 100644 arch/arm/boot/dts/imx6ul-txul-0011.dts
> create mode 100644 arch/arm/boot/dts/imx6ul-txul.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index a4a6d70..f993e7d 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -358,7 +358,9 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
> imx6sx-sdb-reva.dtb \
> imx6sx-sdb.dtb
> dtb-$(CONFIG_SOC_IMX6UL) += \
> - imx6ul-14x14-evk.dtb
> + imx6ul-14x14-evk.dtb \
> + imx6ul-txul-0010.dtb \
> + imx6ul-txul-0011.dtb
> dtb-$(CONFIG_SOC_IMX7D) += \
> imx7d-cl-som-imx7.dtb \
> imx7d-sbc-imx7.dtb \
> diff --git a/arch/arm/boot/dts/imx6ul-txul-0010.dts b/arch/arm/boot/dts/imx6ul-txul-0010.dts
> new file mode 100644
> index 0000000..5e0b09f
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ul-txul-0010.dts
> @@ -0,0 +1,54 @@
> +/*
> + * Copyright 2015 Lothar Waßmann <LW@xxxxxxxxxxxxxxxxxxx>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "imx6ul.dtsi"
> +#include "imx6ul-txul.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TXUL-0010 Module";
> + compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul";
> +
> + aliases {
> + mmc0 = &usdhc1;
> + /delete-property/ mmc1;

Why is this deletion of mmc1 needed?

> + };
> +};
> diff --git a/arch/arm/boot/dts/imx6ul-txul-0011.dts b/arch/arm/boot/dts/imx6ul-txul-0011.dts
> new file mode 100644
> index 0000000..dd3055b
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ul-txul-0011.dts
> @@ -0,0 +1,85 @@
> +/*
> + * Copyright 2015 Lothar Waßmann <LW@xxxxxxxxxxxxxxxxxxx>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "imx6ul.dtsi"
> +#include "imx6ul-txul.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TXUL-0011 Module";
> + compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul";
> +
> + aliases {
> + mmc0 = &usdhc2;
> + mmc1 = &usdhc1;
> + };
> +};
> +
> +&gpmi {
> + status = "disabled";
> +};
> +
> +&iomuxc {
> + imx6ul-txul {

Since commit 5fcdf6a7ed95 (pinctrl: imx: Allow parsing DT without
function nodes), we can save this container node.

> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x070b1
> + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x070b1
> + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x070b1
> + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x070b1
> + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x070b1
> + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x070b1
> + /* eMMC RESET */
> + MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170b0
> + >;
> + };
> + };
> +};
> +
> +&usdhc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + bus-width = <4>;
> + no-1-8-v;
> + non-removable;
> + fsl,wp-controller;
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6ul-txul.dtsi b/arch/arm/boot/dts/imx6ul-txul.dtsi
> new file mode 100644
> index 0000000..12dff96
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6ul-txul.dtsi
> @@ -0,0 +1,962 @@
> +/*
> + * Copyright 2015 Lothar Waßmann <LW@xxxxxxxxxxxxxxxxxxx>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/pwm/pwm.h>
> +
> +/ {
> + aliases {
> + can0 = &can2;
> + can1 = &can1;
> + display = &display;
> + i2c0 = &i2c_gpio;
> + i2c1 = &i2c2;
> + lcdif_23bit_pins_a = &pinctrl_disp0_1;
> + lcdif_24bit_pins_a = &pinctrl_disp0_2;
> + pwm0 = &pwm5;
> + reg_can_xcvr = &reg_can_xcvr;
> + serial2 = &uart5;
> + serial4 = &uart3;
> + spi0 = &ecspi2;
> + spi1 = &spi_gpio;
> + stk5led = &user_led;
> + usbh1 = &usbotg2;
> + usbotg = &usbotg1;
> + };
> +
> + chosen {
> + stdout-path = &uart1;
> + };
> +
> + memory {
> + reg = <0 0>; /* will be filled by U-Boot */
> + };
> +
> + clocks {
> + #address-cells = <1>;
> + #size-cells = <0>;

Have a new line here.

> + mclk: clock@0 {
> + compatible = "fixed-clock";
> + reg = <0>;
> + #clock-cells = <0>;
> + clock-frequency = <26000000>;
> + };
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm5 0 500000 PWM_POLARITY_INVERTED>;
> + power-supply = <&reg_3v3>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";

With no real keys defined? If so, please drop it.

> + };
> +
> + i2c_gpio: i2c-gpio {
> + compatible = "i2c-gpio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c_gpio>;
> + gpios = <
> + &gpio5 1 GPIO_ACTIVE_HIGH /* SDA */
> + &gpio5 0 GPIO_ACTIVE_HIGH /* SCL */
> + >;
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + ds1339: rtc@68 {
> + compatible = "dallas,ds1339";
> + reg = <0x68>;
> + status = "disabled";
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + user_led: user {
> + label = "Heartbeat";
> + gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";

Device tree maintainers do not like this fake simple-bus. Let's put all
these fixed regulators directly under root with the following naming
schema:

reg_xxx: regulator-xxx {
...
};

> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + reg_3v3_etn: regulator@0 {
> + compatible = "regulator-fixed";
> + reg = <0>;
> + regulator-name = "3V3_ETN";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_etnphy_power>;
> + gpio = <&gpio5 7 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_2v5: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "2V5";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-always-on;
> + };
> +
> + reg_3v3: regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_can_xcvr: regulator@3 {
> + compatible = "regulator-fixed";
> + reg = <3>;
> + regulator-name = "CAN XCVR";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan_xcvr>;
> + gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
> + enable-active-low;
> + };
> +
> + reg_lcd_pwr: regulator@5 {
> + compatible = "regulator-fixed";
> + reg = <5>;
> + regulator-name = "LCD POWER";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd_pwr>;
> + gpio = <&gpio5 4 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_lcd_reset: regulator@6 {
> + compatible = "regulator-fixed";
> + reg = <6>;
> + regulator-name = "LCD RESET";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd_reset>;
> + gpio = <&gpio3 4 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_usbh1_vbus: regulator@7 {
> + compatible = "regulator-fixed";
> + reg = <7>;
> + regulator-name = "usbh1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbh1_vbus &pinctrl_usbh1_oc>;
> + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_usbotg_vbus: regulator@8 {
> + compatible = "regulator-fixed";
> + reg = <8>;
> + regulator-name = "usbotg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg_vbus &pinctrl_usbotg_oc>;
> + gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> + };
> +
> + spi_gpio: spi-gpio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "spi-gpio";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spi_gpio>;
> + gpio-mosi = <&gpio1 30 GPIO_ACTIVE_HIGH>;
> + gpio-miso = <&gpio1 31 GPIO_ACTIVE_HIGH>;
> + gpio-sck = <&gpio1 28 GPIO_ACTIVE_HIGH>;
> + num-chipselects = <2>;
> + cs-gpios = <
> + &gpio1 29 GPIO_ACTIVE_HIGH
> + &gpio1 10 GPIO_ACTIVE_HIGH
> + >;
> + status = "disabled";
> +
> + spi@0 {
> + compatible = "spidev";
> + reg = <0>;
> + spi-max-frequency = <660000>;
> + };
> +
> + spi@1 {
> + compatible = "spidev";
> + reg = <1>;
> + spi-max-frequency = <660000>;
> + };
> + };
> +
> + sound {
> + compatible = "karo,imx6ul-tx6ul-sgtl5000",
> + "simple-audio-card";
> + simple-audio-card,name = "imx6ul-tx6ul-sgtl5000-audio";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,bitclock-master = <&codec_dai>;
> + simple-audio-card,frame-master = <&codec_dai>;
> + simple-audio-card,widgets =
> + "Microphone", "Mic Jack",
> + "Line", "Line In",
> + "Line", "Line Out",
> + "Headphone", "Headphone Jack";
> + simple-audio-card,routing =
> + "MIC_IN", "Mic Jack",
> + "Mic Jack", "Mic Bias",
> + "Headphone Jack", "HP_OUT";
> +
> + cpu_dai: simple-audio-card,cpu {
> + sound-dai = <&sai2>;
> + };
> +
> + codec_dai: simple-audio-card,codec {
> + sound-dai = <&sgtl5000>;
> + };
> + };
> +};
> +
> +&can1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan1>;
> + xceiver-supply = <&reg_can_xcvr>;
> + status = "okay";
> +};
> +
> +&can2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan2>;
> + xceiver-supply = <&reg_can_xcvr>;
> + status = "okay";
> +};
> +
> +&ecspi2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi2>;
> + fsl,spi-num-chipselects = <2>;
> + cs-gpios = <
> + &gpio1 29 GPIO_ACTIVE_HIGH
> + &gpio1 10 GPIO_ACTIVE_HIGH
> + >;
> + status = "disabled";
> +
> + spi@0 {
> + compatible = "spidev";
> + reg = <0>;
> + spi-max-frequency = <60000000>;
> + };
> +
> + spi@1 {
> + compatible = "spidev";
> + reg = <1>;
> + spi-max-frequency = <60000000>;
> + };
> +};
> +
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet_mdio>;
> + phy-mode = "rmii";
> + phy-reset-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>;
> + phy-supply = <&reg_3v3_etn>;
> + phy-handle = <&etnphy0>;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + etnphy0: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + interrupt-parent = <&gpio5>;
> + interrupts = <5>;
> + status = "okay";
> + };
> +
> + etnphy1: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + status = "okay";
> + };
> + };
> +};
> +
> +&fec2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet2>;
> + phy-mode = "rmii";
> + phy-supply = <&reg_3v3_etn>;
> + phy-handle = <&etnphy1>;
> + status = "disabled";
> +};
> +
> +&gpmi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpmi_nand>;
> + nand-on-flash-bbt;
> + fsl,no-blockmark-swap;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + sgtl5000: sgtl5000@0a {
> + #sound-dai-cells = <0>;
> + compatible = "fsl,sgtl5000";
> + reg = <0x0a>;
> + VDDA-supply = <&reg_2v5>;
> + VDDIO-supply = <&reg_3v3>;
> + clocks = <&mclk>;
> + };
> +
> + polytouch: edt-ft5x06@38 {
> + compatible = "edt,edt-ft5x06";
> + reg = <0x38>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_edt_ft5x06>;
> + interrupt-parent = <&gpio5>;
> + interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
> + reset-gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
> + wake-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>;
> + linux,wakeup;

This property becomes legacy one. Please use wakeup-source instead.
See Documentation/devicetree/bindings/power/wakeup-source.txt for
details.

> + };
> +
> + touchscreen: tsc2007@48 {
> + compatible = "ti,tsc2007";
> + reg = <0x48>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_tsc2007>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <26 IRQ_TYPE_NONE>;
> + gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
> + ti,x-plate-ohms = <660>;
> + linux,wakeup;

Ditto

> + };
> +};
> +
> +&iomuxc {

I suggest you put iomuxc node at the bottom of the file to make the rest
a bit easier to be read.

> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog>;
> +
> + imx6ul-txul {

Drop this container node.

Shawn

> + pinctrl_hog: hoggrp {
> + fsl,pins = <
> + MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x0b0b0 /* LED */
> + MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x0b0b0 /* ETN PHY RESET */
> + MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x0b0b0 /* ETN PHY INT */
> + >;
> + };
> +
> + pinctrl_disp0_1: disp0grp-1 {
> + fsl,pins = <
> + MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x10 /* LSCLK */
> + MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x10 /* OE_ACD */
> + MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x10 /* HSYNC */
> + MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */
> + /* PAD DISP0_DAT0 is used for the Flexcan transceiver control */
> + MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x10
> + MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x10
> + MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x10
> + MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x10
> + MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x10
> + MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x10
> + MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x10
> + MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x10
> + MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x10
> + MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x10
> + MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x10
> + MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x10
> + MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x10
> + MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x10
> + MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x10
> + MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x10
> + MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x10
> + MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x10
> + MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x10
> + MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x10
> + MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x10
> + MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x10
> + MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x10
> + >;
> + };
> +
> + pinctrl_disp0_2: disp0grp-2 {
> + fsl,pins = <
> + MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x10 /* LSCLK */
> + MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x10 /* OE_ACD */
> + MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x10 /* HSYNC */
> + MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */
> + MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x10
> + MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x10
> + MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x10
> + MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x10
> + MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x10
> + MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x10
> + MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x10
> + MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x10
> + MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x10
> + MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x10
> + MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x10
> + MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x10
> + MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x10
> + MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x10
> + MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x10
> + MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x10
> + MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x10
> + MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x10
> + MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x10
> + MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x10
> + MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x10
> + MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x10
> + MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x10
> + MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x10
> + >;
> + };
> +
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x0b0b0 /* CSPI_SS */
> + MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x0b0b0 /* CSPI_SS */
> + MX6UL_PAD_UART5_TX_DATA__ECSPI2_MOSI 0x0b0b0 /* CSPI_MOSI */
> + MX6UL_PAD_UART5_RX_DATA__ECSPI2_MISO 0x0b0b0 /* CSPI_MISO */
> + MX6UL_PAD_UART4_TX_DATA__ECSPI2_SCLK 0x0b0b0 /* CSPI_SCLK */
> + >;
> + };
> +
> + pinctrl_edt_ft5x06: edt-ft5x06grp {
> + fsl,pins = <
> + MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* Interrupt */
> + MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* Reset */
> + MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x1b0b0 /* Wake */
> + >;
> + };
> +
> + pinctrl_enet1: enet1grp {
> + fsl,pins = <
> + MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x0b0b0
> + MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x0b0b0
> + MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x0b0b0
> + MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x0b0b0
> + MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x0b0b0
> + MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x0b0b0
> + MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x0b0b0
> + MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x40000031
> + >;
> + };
> +
> + pinctrl_enet2: enet2grp {
> + fsl,pins = <
> + MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x0b0b0
> + MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x0b0b0
> + MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x0b0b0
> + MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x0b0b0
> + MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x0b0b0
> + MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x0b0b0
> + MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x0b0b0
> + MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x40000031
> + >;
> + };
> +
> + pinctrl_enet_mdio: enet-mdiogrp {
> + fsl,pins = <
> + MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x0b0b0
> + MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
> + >;
> + };
> +
> + pinctrl_etnphy_power: etnphy-pwrgrp {
> + fsl,pins = <
> + MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x0b0b0 /* ETN PHY POWER */
> + >;
> + };
> +
> + pinctrl_flexcan1: flexcan1grp {
> + fsl,pins = <
> + MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b0b0
> + MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b0b0
> + >;
> + };
> +
> + pinctrl_flexcan2: flexcan2grp {
> + fsl,pins = <
> + MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b0b0
> + MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b0b0
> + >;
> + };
> +
> + pinctrl_flexcan_xcvr: flexcan-xcvrgrp {
> + fsl,pins = <
> + MX6UL_PAD_LCD_DATA00__GPIO3_IO05 0x0b0b0 /* Flexcan XCVR enable */
> + >;
> + };
> +
> + pinctrl_gpmi_nand: gpminandgrp {
> + fsl,pins = <
> + MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0x0b0b1
> + MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0x0b0b1
> + MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0x0b0b1
> + MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0x0b000
> + MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0x0b0b1
> + MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0x0b0b1
> + MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0x0b0b1
> + MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x0b0b1
> + MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0x0b0b1
> + MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0x0b0b1
> + MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0x0b0b1
> + MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0x0b0b1
> + MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0x0b0b1
> + MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0x0b0b1
> + MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0x0b0b1
> + >;
> + };
> +
> + pinctrl_i2c_gpio: i2c-gpiogrp {
> + fsl,pins = <
> + MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x4001b8b1 /* I2C SCL */
> + MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x4001b8b1 /* I2C SDA */
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX6UL_PAD_GPIO1_IO00__I2C2_SCL 0x4001b8b1
> + MX6UL_PAD_GPIO1_IO01__I2C2_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_kpp: kppgrp {
> + fsl,pins = <
> + MX6UL_PAD_ENET2_RX_DATA1__KPP_COL04 0x1b0b0
> + MX6UL_PAD_ENET2_TX_DATA0__KPP_COL05 0x1b0b0
> + MX6UL_PAD_ENET2_TX_EN__KPP_COL06 0x1b0b0
> + MX6UL_PAD_ENET2_RX_ER__KPP_COL07 0x1b0b0
> + MX6UL_PAD_ENET2_RX_DATA0__KPP_ROW04 0x1b0b0
> + MX6UL_PAD_ENET2_RX_EN__KPP_ROW05 0x1b0b0
> + MX6UL_PAD_ENET2_TX_DATA1__KPP_ROW06 0x1b0b0
> + MX6UL_PAD_ENET2_TX_CLK__KPP_ROW07 0x1b0b0
> + >;
> + };
> +
> + pinctrl_lcd_pwr: lcd-pwrgrp {
> + fsl,pins = <
> + MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x0b0b0 /* LCD Power Enable */
> + >;
> + };
> +
> + pinctrl_lcd_reset: lcd-resetgrp {
> + fsl,pins = <
> + MX6UL_PAD_LCD_RESET__GPIO3_IO04 0x0b0b0 /* LCD RESET */
> + >;
> + };
> +
> + pinctrl_pwm5: pwm5grp {
> + fsl,pins = <
> + MX6UL_PAD_NAND_DQS__PWM5_OUT 0x0b0b0
> + >;
> + };
> +
> + pinctrl_sai2: sai2grp {
> + fsl,pins = <
> + MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x0b0b0 /* SSI1_RXD */
> + MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x0b0b0 /* SSI1_TXD */
> + MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x0b0b0 /* SSI1_CLK */
> + MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x0b0b0 /* SSI1_FS */
> + >;
> + };
> +
> + pinctrl_spi_gpio: spi-gpiogrp {
> + fsl,pins = <
> + MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x0b0b0 /* CSPI_SS */
> + MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x0b0b0 /* CSPI_SS */
> + MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x0b0b0 /* CSPI_MOSI */
> + MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x0b0b0 /* CSPI_MISO */
> + MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x0b0b0 /* CSPI_SCLK */
> + >;
> + };
> +
> + pinctrl_tsc2007: tsc2007grp {
> + fsl,pins = <
> + MX6UL_PAD_JTAG_TMS__GPIO1_IO11 0x1b0b0 /* Interrupt */
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x0b0b0
> + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x0b0b0
> + >;
> + };
> +
> + pinctrl_uart1_rtscts: uart1_rtsctsgrp {
> + fsl,pins = <
> + MX6UL_PAD_UART1_RTS_B__UART1_DCE_RTS 0x0b0b0
> + MX6UL_PAD_UART1_CTS_B__UART1_DCE_CTS 0x0b0b0
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x0b0b0
> + MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x0b0b0
> + >;
> + };
> +
> + pinctrl_uart2_rtscts: uart2_rtsctsgrp {
> + fsl,pins = <
> + MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x0b0b0
> + MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x0b0b0
> + >;
> + };
> +
> + pinctrl_uart5: uart5grp {
> + fsl,pins = <
> + MX6UL_PAD_GPIO1_IO04__UART5_DCE_TX 0x0b0b0
> + MX6UL_PAD_GPIO1_IO05__UART5_DCE_RX 0x0b0b0
> + >;
> + };
> +
> + pinctrl_uart5_rtscts: uart5_rtsctsgrp {
> + fsl,pins = <
> + MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS 0x0b0b0
> + MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS 0x0b0b0
> + >;
> + };
> +
> + pinctrl_usbh1_oc: usbh1-ocgrp {
> + fsl,pins = <
> + MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0x17059 /* USBH1_OC */
> + >;
> + };
> +
> + pinctrl_usbh1_vbus: usbh1-vbusgrp {
> + fsl,pins = <
> + MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0x0b0b0 /* USBH1_VBUSEN */
> + >;
> + };
> +
> + pinctrl_usbotg_oc: usbotg-ocgrp {
> + fsl,pins = <
> + MX6UL_PAD_UART3_RTS_B__GPIO1_IO27 0x17059 /* USBOTG_OC */
> + >;
> + };
> +
> + pinctrl_usbotg_vbus: usbotg-vbusgrp {
> + fsl,pins = <
> + MX6UL_PAD_UART3_CTS_B__GPIO1_IO26 0x1b0b0 /* USBOTG_VBUSEN */
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x070b1
> + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x07099
> + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x070b1
> + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x070b1
> + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x070b1
> + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x070b1
> + /* SD1 CD */
> + MX6UL_PAD_NAND_CE1_B__GPIO4_IO14 0x170b0 /* SD1 CD */
> + >;
> + };
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x070b1
> + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x070b1
> + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x070b1
> + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x070b1
> + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x070b1
> + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x070b1
> + /* eMMC RESET */
> + MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170b0
> + >;
> + };
> + };
> +};
> +
> +&kpp {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_kpp>;
> + /* sample keymap */
> + /* row/col 0..3 are mapped to KPP row/col 4..7 */
> + linux,keymap = <
> + MATRIX_KEY(4, 4, KEY_POWER)
> + MATRIX_KEY(4, 5, KEY_KP0)
> + MATRIX_KEY(4, 6, KEY_KP1)
> + MATRIX_KEY(4, 7, KEY_KP2)
> + MATRIX_KEY(5, 4, KEY_KP3)
> + MATRIX_KEY(5, 5, KEY_KP4)
> + MATRIX_KEY(5, 6, KEY_KP5)
> + MATRIX_KEY(5, 7, KEY_KP6)
> + MATRIX_KEY(6, 4, KEY_KP7)
> + MATRIX_KEY(6, 5, KEY_KP8)
> + MATRIX_KEY(6, 6, KEY_KP9)
> + >;
> + status = "okay";
> +};
> +
> +&lcdif {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_1>;
> + lcd-supply = <&reg_lcd_pwr>;
> + display = <&display>;
> + status = "okay";
> +
> + display: display@di0 {
> + bits-per-pixel = <32>;
> + bus-width = <24>;
> + status = "okay";
> +
> + display-timings {
> + VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> + };
> + };
> +};
> +
> +&pwm5 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm5>;
> + #pwm-cells = <3>;
> + status = "okay";
> +};
> +
> +&sai2 {
> + #sound-dai-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_sai2>;
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_rtscts>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2 &pinctrl_uart2_rtscts>;
> + status = "okay";
> +};
> +
> +&uart5 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart5 &pinctrl_uart5_rtscts>;
> + status = "okay";
> +};
> +
> +&usbotg2 {
> + vbus-supply = <&reg_usbh1_vbus>;
> + dr_mode = "host";
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usbotg1 {
> + vbus-supply = <&reg_usbotg_vbus>;
> + dr_mode = "peripheral";
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + bus-width = <4>;
> + no-1-8-v;
> + cd-gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
> + fsl,wp-controller;
> + status = "okay";
> +};
> --
> 2.1.4
>
>