[PATCH] Staging: comedi: ni_atmio: fixed spacing and comment style issues

[Steven Laabs]

Fixed coding style issues.

Signed-off-by: Steven Laabs <swlaabs@xxxxxxxxx>
---
 drivers/staging/comedi/drivers/ni_atmio.c | 180 +++++++++++++++---------------
 1 file changed, 91 insertions(+), 89 deletions(-)

diff --git a/drivers/staging/comedi/drivers/ni_atmio.c b/drivers/staging/comedi/drivers/ni_atmio.c
index 95435b8..f957790 100644
--- a/drivers/staging/comedi/drivers/ni_atmio.c
+++ b/drivers/staging/comedi/drivers/ni_atmio.c
@@ -1,93 +1,95 @@
 /*
-    comedi/drivers/ni_atmio.c
-    Hardware driver for NI AT-MIO E series cards
-
-    COMEDI - Linux Control and Measurement Device Interface
-    Copyright (C) 1997-2001 David A. Schleef <ds@xxxxxxxxxxx>
-
-    This program is free software; you can redistribute it and/or modify
-    it under the terms of the GNU General Public License as published by
-    the Free Software Foundation; either version 2 of the License, or
-    (at your option) any later version.
-
-    This program is distributed in the hope that it will be useful,
-    but WITHOUT ANY WARRANTY; without even the implied warranty of
-    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-    GNU General Public License for more details.
-*/
-/*
-Driver: ni_atmio
-Description: National Instruments AT-MIO-E series
-Author: ds
-Devices: [National Instruments] AT-MIO-16E-1 (ni_atmio),
-  AT-MIO-16E-2, AT-MIO-16E-10, AT-MIO-16DE-10, AT-MIO-64E-3,
-  AT-MIO-16XE-50, AT-MIO-16XE-10, AT-AI-16XE-10
-Status: works
-Updated: Thu May  1 20:03:02 CDT 2003
-
-The driver has 2.6 kernel isapnp support, and
-will automatically probe for a supported board if the
-I/O base is left unspecified with comedi_config.
-However, many of
-the isapnp id numbers are unknown.  If your board is not
-recognized, please send the output of 'cat /proc/isapnp'
-(you may need to modprobe the isa-pnp module for
-/proc/isapnp to exist) so the
-id numbers for your board can be added to the driver.
-
-Otherwise, you can use the isapnptools package to configure
-your board.  Use isapnp to
-configure the I/O base and IRQ for the board, and then pass
-the same values as
-parameters in comedi_config.  A sample isapnp.conf file is included
-in the etc/ directory of Comedilib.
-
-Comedilib includes a utility to autocalibrate these boards.  The
-boards seem to boot into a state where the all calibration DACs
-are at one extreme of their range, thus the default calibration
-is terrible.  Calibration at boot is strongly encouraged.
-
-To use the extended digital I/O on some of the boards, enable the
-8255 driver when configuring the Comedi source tree.
-
-External triggering is supported for some events.  The channel index
-(scan_begin_arg, etc.) maps to PFI0 - PFI9.
-
-Some of the more esoteric triggering possibilities of these boards
-are not supported.
-*/
-/*
-	The real guts of the driver is in ni_mio_common.c, which is included
-	both here and in ni_pcimio.c
-
-	Interrupt support added by Truxton Fulton <trux@xxxxxxxxxxx>
-
-	References for specifications:
-
-	   340747b.pdf  Register Level Programmer Manual (obsolete)
-	   340747c.pdf  Register Level Programmer Manual (new)
-	   DAQ-STC reference manual
-
-	Other possibly relevant info:
-
-	   320517c.pdf  User manual (obsolete)
-	   320517f.pdf  User manual (new)
-	   320889a.pdf  delete
-	   320906c.pdf  maximum signal ratings
-	   321066a.pdf  about 16x
-	   321791a.pdf  discontinuation of at-mio-16e-10 rev. c
-	   321808a.pdf  about at-mio-16e-10 rev P
-	   321837a.pdf  discontinuation of at-mio-16de-10 rev d
-	   321838a.pdf  about at-mio-16de-10 rev N
-
-	ISSUES:
-
-	need to deal with external reference for DAC, and other DAC
-	properties in board properties
+ *    comedi/drivers/ni_atmio.c
+ *    Hardware driver for NI AT-MIO E series cards
+ *
+ *    COMEDI - Linux Control and Measurement Device Interface
+ *    Copyright (C) 1997-2001 David A. Schleef <ds@xxxxxxxxxxx>
+ *
+ *    This program is free software; you can redistribute it and/or modify
+ *    it under the terms of the GNU General Public License as published by
+ *    the Free Software Foundation; either version 2 of the License, or
+ *    (at your option) any later version.
+ *
+ *    This program is distributed in the hope that it will be useful,
+ *    but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *    GNU General Public License for more details.
+ */
 
-	deal with at-mio-16de-10 revision D to N changes, etc.
+/*
+ * Driver: ni_atmio
+ * Description: National Instruments AT-MIO-E series
+ * Author: ds
+ * Devices: [National Instruments] AT-MIO-16E-1 (ni_atmio),
+ *   AT-MIO-16E-2, AT-MIO-16E-10, AT-MIO-16DE-10, AT-MIO-64E-3,
+ *   AT-MIO-16XE-50, AT-MIO-16XE-10, AT-AI-16XE-10
+ * Status: works
+ * Updated: Thu May  1 20:03:02 CDT 2003
+ *
+ * The driver has 2.6 kernel isapnp support, and
+ * will automatically probe for a supported board if the
+ * I/O base is left unspecified with comedi_config.
+ * However, many of
+ * the isapnp id numbers are unknown.  If your board is not
+ * recognized, please send the output of 'cat /proc/isapnp'
+ * (you may need to modprobe the isa-pnp module for
+ * /proc/isapnp to exist) so the
+ * id numbers for your board can be added to the driver.
+ *
+ * Otherwise, you can use the isapnptools package to configure
+ * your board.  Use isapnp to
+ * configure the I/O base and IRQ for the board, and then pass
+ * the same values as
+ * parameters in comedi_config.  A sample isapnp.conf file is included
+ * in the etc/ directory of Comedilib.
+ *
+ * Comedilib includes a utility to autocalibrate these boards.  The
+ * boards seem to boot into a state where the all calibration DACs
+ * are at one extreme of their range, thus the default calibration
+ * is terrible.  Calibration at boot is strongly encouraged.
+ *
+ * To use the extended digital I/O on some of the boards, enable the
+ * 8255 driver when configuring the Comedi source tree.
+ *
+ * External triggering is supported for some events.  The channel index
+ * (scan_begin_arg, etc.) maps to PFI0 - PFI9.
+ *
+ * Some of the more esoteric triggering possibilities of these boards
+ * are not supported.
+ */
 
-*/
+/*
+ * The real guts of the driver is in ni_mio_common.c, which is included
+ * both here and in ni_pcimio.c
+ *
+ * Interrupt support added by Truxton Fulton <trux@xxxxxxxxxxx>
+ *
+ * References for specifications:
+ *
+ *    340747b.pdf  Register Level Programmer Manual (obsolete)
+ *    340747c.pdf  Register Level Programmer Manual (new)
+ *    DAQ-STC reference manual
+ *
+ * Other possibly relevant info:
+ *
+ *    320517c.pdf  User manual (obsolete)
+ *    320517f.pdf  User manual (new)
+ *    320889a.pdf  delete
+ *    320906c.pdf  maximum signal ratings
+ *    321066a.pdf  about 16x
+ *    321791a.pdf  discontinuation of at-mio-16e-10 rev. c
+ *    321808a.pdf  about at-mio-16e-10 rev P
+ *    321837a.pdf  discontinuation of at-mio-16de-10 rev d
+ *    321838a.pdf  about at-mio-16de-10 rev N
+ *
+ * ISSUES:
+ *
+ * need to deal with external reference for DAC, and other DAC
+ * properties in board properties
+ *
+ * deal with at-mio-16de-10 revision D to N changes, etc.
+ *
+ */
 
 #include <linux/module.h>
 #include <linux/interrupt.h>
@@ -287,10 +289,10 @@ static const struct ni_board_struct *ni_atmio_probe(struct comedi_device *dev)
 	}
 	if (device_id == 255)
 		dev_err(dev->class_dev, "can't find board\n");
-	 else if (device_id == 0)
+	else if (device_id == 0)
 		dev_err(dev->class_dev,
 			"EEPROM read error (?) or device not found\n");
-	 else
+	else
 		dev_err(dev->class_dev,
 			"unknown device ID %d -- contact author\n", device_id);
 
-- 
2.1.4