Re: [PATCH v5 0/13] arm64: allwinner: a64: Enable MMC support

From: Ulf Hansson
Date: Mon Jan 30 2017 - 05:17:58 EST


On 27 January 2017 at 22:38, Maxime Ripard
<maxime.ripard@xxxxxxxxxxxxxxxxxx> wrote:
> Hi,
>
> Here is a new attempt at getting the MMC controllers running, following the
> work done by Andre.
>
> This has been tested on a board with one SDIO device (a Marvell WiFi chip)
> and a Kingston eMMC with 1.8V IOs.
>
> For SDIO, the HS DDR mode works just fine. That serie also enables the
> SDR104 mode to work on the devices that are capable of this.
>
> For the eMMC, HS200 with the voltage switch works. HS400 doesn't at the
> moment, but since it's significantly more complex, and at the same time
> Allwinner recommends to limit its frequency to 100MHz, this doesn't have
> any benefits. If there's any at some point, this can be added later.
>
> Let me know what you think,
> Maxime
>
> Changes from v4:
> - Added Florian Tested-by
> - Removed duplicate commit log
>
> Changes from v3:
> - Reordered the MMC nodes
> - Added the specification section the first commit log
> - Supported mmc->actual_rate
> - Clarified a bit what we (don't) know about DATA0
>
> Changes from v2:
> - Enabled SDR104, limited the frequency to 150MHz. 200MHz was too high.
> - Added more fixes to the gating and frequency rate change sequence
> - Added one more patch to mask DATA0 when updating the clock that was
> needed to get SDR104 to run
> - Added the patches to enable it on a few boards done by Andre
> - Amended the comments as suggested by Andre.
> - Added some tags
>
> Andre Przywara (4):
> arm64: allwinner: a64: Add MMC nodes
> arm64: allwinner: pine64: add MMC support
> arm64: allwinner: a64: add UART1 pin nodes
> arm64: allwinner: add BananaPi-M64 support
>
> Maxime Ripard (9):
> mmc: sunxi: Fix clock frequency change sequence
> mmc: sunxi: Gate the clock when rate is 0
> mmc: sunxi: Always set signal delay to 0 for A64
> mmc: sunxi: Enable the new timings for the A64 MMC controllers
> mmc: sunxi: Mask DATA0 when updating the clock
> mmc: sunxi: Add EMMC (MMC2) controller compatible
> mmc: sunxi: Add more debug informations
> arm64: allwinner: a64: Add MMC pinctrl nodes
> arm64: allwinner: a64: Increase the MMC max frequency
>
> arch/arm64/boot/dts/allwinner/Makefile | 1 +-
> arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 120 +++++++-
> arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts | 20 +-
> arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 77 ++++-
> drivers/mmc/host/sunxi-mmc.c | 114 ++++---
> 5 files changed, 289 insertions(+), 43 deletions(-)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
>
> base-commit: c94f7962e97c2ba0a612656bc456d979f20cb382
> --
> git-series 0.8.11

Thanks, applied patch 1 -> 7 for next! Although, please have a look at
my comment for patch6.

Kind regards
Uffe