[PATCH v5 14/23] mtd: nand: denali: fix bank reset function to detect the number of chips

From: Masahiro Yamada
Date: Wed Jun 07 2017 - 07:57:54 EST


The nand_scan_ident() iterates over maxchips, and calls nand_reset()
for each. This driver currently passes the maximum number of banks
(=chip selects) supported by the controller as maxchips. So, maxchips
is typically 4 or 8. Usually, less number of NAND chips are connected
to the controller.

This can be a problem for ONFi devices. Now, this driver implements
->setup_data_interface() hook, so nand_setup_data_interface() issues
Set Features (0xEF) command, which waits until the chip returns R/B#
response. If no chip there, we know it never happens, but the driver
still ends up with waiting for a long time. It will finally bail-out
with timeout error and the driver will work with existing chips, but
unnecessary wait will give a bad user experience.

The denali_nand_reset() polls the INTR__RST_COMP and INTR__TIME_OUT
bits, but they are always set even if not NAND chip is connected to
that bank. To know the chip existence, INTR__INT_ACT bit must be
checked; this flag is set only when R/B# is toggled. Since the Reset
(0xFF) command toggles the R/B# pin, this can be used to know the
actual number of chips, and update denali->max_banks.

Signed-off-by: Masahiro Yamada <yamada.masahiro@xxxxxxxxxxxxx>
---

Boris mentioned this information can be retrieved from DT
(http://patchwork.ozlabs.org/patch/745118/), but I'd like to
take time for controller/chip decoupling. I am tackling on
that, but not completed yet.

I believe this commit stands for denali_pci, at least I do not
know how to get the number of chips from PCI.


Changes in v5: None
Changes in v4:
- Reword commit-log

Changes in v3: None
Changes in v2:
- Newly added

drivers/mtd/nand/denali.c | 52 +++++++++++++++++++++--------------------------
1 file changed, 23 insertions(+), 29 deletions(-)

diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c
index 95bce6b341d7..8e2399ddfe3f 100644
--- a/drivers/mtd/nand/denali.c
+++ b/drivers/mtd/nand/denali.c
@@ -85,33 +85,6 @@ static void index_addr(struct denali_nand_info *denali,
iowrite32(data, denali->flash_mem + 0x10);
}

-/* Reset the flash controller */
-static uint16_t denali_nand_reset(struct denali_nand_info *denali)
-{
- int i;
-
- for (i = 0; i < denali->max_banks; i++)
- iowrite32(INTR__RST_COMP | INTR__TIME_OUT,
- denali->flash_reg + INTR_STATUS(i));
-
- for (i = 0; i < denali->max_banks; i++) {
- iowrite32(1 << i, denali->flash_reg + DEVICE_RESET);
- while (!(ioread32(denali->flash_reg + INTR_STATUS(i)) &
- (INTR__RST_COMP | INTR__TIME_OUT)))
- cpu_relax();
- if (ioread32(denali->flash_reg + INTR_STATUS(i)) &
- INTR__TIME_OUT)
- dev_dbg(denali->dev,
- "NAND Reset operation timed out on bank %d\n", i);
- }
-
- for (i = 0; i < denali->max_banks; i++)
- iowrite32(INTR__RST_COMP | INTR__TIME_OUT,
- denali->flash_reg + INTR_STATUS(i));
-
- return PASS;
-}
-
/*
* Use the configuration feature register to determine the maximum number of
* banks that the hardware supports.
@@ -999,7 +972,28 @@ static int denali_setup_data_interface(struct mtd_info *mtd,
return 0;
}

-/* Initialization code to bring the device up to a known good state */
+static void denali_reset_banks(struct denali_nand_info *denali)
+{
+ int i;
+
+ denali_clear_irq_all(denali);
+
+ for (i = 0; i < denali->max_banks; i++) {
+ iowrite32(1 << i, denali->flash_reg + DEVICE_RESET);
+ while (!(ioread32(denali->flash_reg + INTR_STATUS(i)) &
+ (INTR__RST_COMP | INTR__TIME_OUT)))
+ cpu_relax();
+ if (!(ioread32(denali->flash_reg + INTR_STATUS(i)) &
+ INTR__INT_ACT))
+ break;
+ }
+
+ dev_dbg(denali->dev, "%d chips connected\n", i);
+ denali->max_banks = i;
+
+ denali_clear_irq_all(denali);
+}
+
static void denali_hw_init(struct denali_nand_info *denali)
{
/*
@@ -1019,7 +1013,7 @@ static void denali_hw_init(struct denali_nand_info *denali)
denali->bbtskipbytes = ioread32(denali->flash_reg +
SPARE_AREA_SKIP_BYTES);
detect_max_banks(denali);
- denali_nand_reset(denali);
+ denali_reset_banks(denali);
iowrite32(0x0F, denali->flash_reg + RB_PIN_ENABLED);
iowrite32(CHIP_EN_DONT_CARE__FLAG,
denali->flash_reg + CHIP_ENABLE_DONT_CARE);
--
2.7.4