Re: [PATCH v3 0/3] mmc: Add OMAP SDHCI driver
From: Ulf Hansson
Date: Fri Sep 22 2017 - 05:45:21 EST
On 6 September 2017 at 13:45, Kishon Vijay Abraham I <kishon@xxxxxx> wrote:
> This is the first step in deprecating omap_hsmmc driver completely
> and moving to sdhci-omap driver which uses the sdhci library.
> This patch that adds a new SDHCI quirk "MMC_RSP_136" has already been
> merged and hence removed it in this revision.
> Apart from the quirk, sdhci-omap has it's own callbacks
> to set_clock (clock divider programming is different from generic sdhci)
> , set_power, set_bus_width, set_bus_mode and platform_send_init_74_clocks.
> These callback functions are implemented based on omap_hsmmc driver.
> Since sdhci-omap driver requires pbias regulator fixes to be present, I've
> sent them as part of this series.
> The sdhci-omap driver supports only the high speed mode and UHS/HS200
> mode will be added in a later series.
> It has been tested only in boards having DRA7 SoCs like dra7-evm, dra72-evm,
> am571x-idk, am572x-idk, am57xx-evm. (Tested only eMMC and SD.
> SDIO support will be added later). The plan is to fully convert DRA7
> SoC to use SDHCI driver and then convert other legacy platforms to use
> For sdhci-omap to be functional, the following tag should be merged (There
> are no compilation dependencies).
> However the above regulator tag will impact omap_hsmmc driver. so 
> should be merged before everything else is merged.
>  -> https://lkml.org/lkml/2017/8/31/300
> The patch to add config and dts changes to use sdhci-omap will be sent
> Next Steps:
> *) Add UHS support to sdhci-omap
> *) Add SDIO support
> *) Add support for older TI platforms
> Changes from v3:
> *) removed omap_hsmmc and pbias-regulator patches from the series
> *) Fixed dt-binding documentation (remove '0x' in node name)
> *) stop clock if MMC core sends '0' in frequency
> Changes from v2:
> *) Rebased on git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc.git next
> *) Included a couple of patches from Ravikumar to fix pbias-regulator driver
> to support max-voltage of 3.3V. This is required for sdhci-omap driver.
> *) Create sdhci-omap as a new driver with MMC generic bindings and hence doesn't
> have bindings like ti,dual-volt added for omap-hsmmc. (Instead of
> ti,dual-volt, sdhci-omap driver uses the supported regulator voltage to
> set controller IO voltage capabilities).
> When omap-hsmmc driver is deprecated, support for these properties will
> be added to sdhci-omap.
> *) Fixed minor comments from Adrian).
> Changes from v1:
> *) Remove the quirks and instead use sdhci_omap specific callbacks for
> set_power, set_busmode etc.
> *) Add a patch from Adrian to tidy reading 136-bit responses
> I've also pushed the entire series along with dependent dt patches @
> https://github.com/kishon/linux-wip.git sdhci_v3 (in case someone
> wants to test)
> Kishon Vijay Abraham I (3):
> dt-bindings: sdhci-omap: Add bindings for the sdhci-omap controller
> mmc: sdhci-omap: Add OMAP SDHCI driver
> MAINTAINERS: Add TI OMAP SDHCI Maintainer
> .../devicetree/bindings/mmc/sdhci-omap.txt | 16 +
> MAINTAINERS | 6 +
> drivers/mmc/host/Kconfig | 12 +
> drivers/mmc/host/Makefile | 1 +
> drivers/mmc/host/sdhci-omap.c | 607 +++++++++++++++++++++
> 5 files changed, 642 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-omap.txt
> create mode 100644 drivers/mmc/host/sdhci-omap.c
Thanks, everything applied/pulled for next! Great work!