Re: [PATCH v4 1/2] Input: Add driver for Cypress Generation 5 touchscreen
From: Dmitry Torokhov
Date: Tue Jan 23 2018 - 12:31:05 EST
On Tue, Jan 23, 2018 at 11:44:59AM +0100, Mylene Josserand wrote:
> Hi Dmitry,
>
> Thank you for the review.
>
> Le Mon, 22 Jan 2018 20:15:03 -0800,
> Dmitry Torokhov <dmitry.torokhov@xxxxxxxxx> a écrit :
>
> > Hi Mylène,
> >
> > On Fri, Dec 01, 2017 at 04:39:56PM +0100, Mylène Josserand wrote:
> > > This is the basic driver for the Cypress TrueTouch Gen5 touchscreen
> > > controllers. This driver supports only the I2C bus but it uses regmap
> > > so SPI support could be added later.
> > > The touchscreen can retrieve some defined zone that are handled as
> > > buttons (according to the hardware). That is why it handles
> > > button and multitouch events.
> > >
> > > Reviewed-by: Maxime Ripard <maxime.ripard@xxxxxxxxxxxxxxxxxx>
> > > Signed-off-by: Mylène Josserand <mylene.josserand@xxxxxxxxxxxxxxxxxx>
> > > ---
> > > drivers/input/touchscreen/Kconfig | 16 +
> > > drivers/input/touchscreen/Makefile | 1 +
> > > drivers/input/touchscreen/cyttsp5.c | 1110 +++++++++++++++++++++++++++++++++++
> > > 3 files changed, 1127 insertions(+)
> > > create mode 100644 drivers/input/touchscreen/cyttsp5.c
> > >
> > > diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
> > > index 0cfdb7cb610e..28eea6d5f1bb 100644
> > > --- a/drivers/input/touchscreen/Kconfig
> > > +++ b/drivers/input/touchscreen/Kconfig
> > > @@ -238,6 +238,22 @@ config TOUCHSCREEN_CYTTSP4_SPI
> > > To compile this driver as a module, choose M here: the
> > > module will be called cyttsp4_spi.
> > >
> > > +config TOUCHSCREEN_CYTTSP5
> > > + tristate "Cypress TrueTouch Gen5 Touchscreen Driver"
> > > + depends on OF
> >
> > Does it have to be? Please use generic device properties
> > (device_property_* API) and it can be used with ACPI and static board
> > files, of needed.
>
> Okay, I will try with that.
>
> >
> > > + select REGMAP_I2C
> > > + select CRC_ITU_T
> > > + help
> > > + Driver for Parade TrueTouch Standard Product
> > > + Generation 5 touchscreen controllers.
> > > + I2C bus interface support only.
> > > +
> > > + Say Y here if you have a Cypress Gen5 touchscreen.
> > > + If unsure, say N.
> > > +
> > > + To compile this driver as a module, choose M here: the
> > > + module will be called cyttsp5.
> > > +
> > > config TOUCHSCREEN_DA9034
> > > tristate "Touchscreen support for Dialog Semiconductor DA9034"
> > > depends on PMIC_DA903X
> > > diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
> > > index d2a2b3b7af27..e7d124901dd9 100644
> > > --- a/drivers/input/touchscreen/Makefile
> > > +++ b/drivers/input/touchscreen/Makefile
> > > @@ -26,6 +26,7 @@ obj-$(CONFIG_TOUCHSCREEN_CYTTSP_SPI) += cyttsp_spi.o
> > > obj-$(CONFIG_TOUCHSCREEN_CYTTSP4_CORE) += cyttsp4_core.o
> > > obj-$(CONFIG_TOUCHSCREEN_CYTTSP4_I2C) += cyttsp4_i2c.o cyttsp_i2c_common.o
> > > obj-$(CONFIG_TOUCHSCREEN_CYTTSP4_SPI) += cyttsp4_spi.o
> > > +obj-$(CONFIG_TOUCHSCREEN_CYTTSP5) += cyttsp5.o
> > > obj-$(CONFIG_TOUCHSCREEN_DA9034) += da9034-ts.o
> > > obj-$(CONFIG_TOUCHSCREEN_DA9052) += da9052_tsi.o
> > > obj-$(CONFIG_TOUCHSCREEN_DYNAPRO) += dynapro.o
> > > diff --git a/drivers/input/touchscreen/cyttsp5.c b/drivers/input/touchscreen/cyttsp5.c
> > > new file mode 100644
> > > index 000000000000..a41feea2cd5a
> > > --- /dev/null
> > > +++ b/drivers/input/touchscreen/cyttsp5.c
> > > @@ -0,0 +1,1110 @@
> > > +/*
> > > + * Parade TrueTouch(TM) Standard Product V5 Module.
> > > + * For use with Parade touchscreen controllers.
> > > + *
> > > + * Copyright (C) 2015 Parade Technologies
> > > + * Copyright (C) 2012-2015 Cypress Semiconductor
> > > + * Copyright (C) 2017 Free Electrons
> > > + *
> > > + * Author: Mylène Josserand <mylene.josserand@xxxxxxxxxxxxxxxxxx>
> > > + *
> > > + * This program is free software; you can redistribute it and/or
> > > + * modify it under the terms of the GNU General Public License
> > > + * version 2, and only version 2, as published by the
> > > + * Free Software Foundation.
> > > + *
> > > + * This program is distributed in the hope that it will be useful,
> > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > > + * GNU General Public License for more details.
> > > + *
> > > + */
> > > +
> > > +#include <asm/unaligned.h>
> > > +#include <linux/crc-itu-t.h>
> > > +#include <linux/delay.h>
> > > +#include <linux/device.h>
> > > +#include <linux/gpio.h>
> > > +#include <linux/input/mt.h>
> > > +#include <linux/input/touchscreen.h>
> > > +#include <linux/interrupt.h>
> > > +#include <linux/i2c.h>
> > > +#include <linux/module.h>
> > > +#include <linux/of_device.h>
> > > +#include <linux/regmap.h>
> > > +
> > > +#define CYTTSP5_NAME "cyttsp5"
> > > +#define CY_I2C_DATA_SIZE (2 * 256)
> > > +#define HID_VERSION 0x0100
> > > +#define CY_MAX_INPUT 512
> > > +#define CYTTSP5_PREALLOCATED_CMD_BUFFER 32
> > > +#define CY_BITS_PER_BTN 1
> > > +#define CY_NUM_BTN_EVENT_ID ((1 << CY_BITS_PER_BTN) - 1)
> > > +
> > > +#define MAX_AREA 255
> > > +#define HID_OUTPUT_BL_SOP 0x1
> > > +#define HID_OUTPUT_BL_EOP 0x17
> > > +#define HID_OUTPUT_BL_LAUNCH_APP 0x3B
> > > +#define HID_OUTPUT_BL_LAUNCH_APP_SIZE 11
> > > +#define HID_OUTPUT_GET_SYSINFO 0x2
> > > +#define HID_OUTPUT_GET_SYSINFO_SIZE 5
> > > +
> > > +#define HID_DESC_REG 0x1
> > > +#define HID_INPUT_REG 0x3
> > > +#define HID_OUTPUT_REG 0x4
> > > +
> > > +#define REPORT_ID_TOUCH 0x1
> > > +#define REPORT_ID_BTN 0x3
> > > +#define REPORT_SIZE_5 5
> > > +#define REPORT_SIZE_8 8
> > > +#define REPORT_SIZE_16 16
> > > +
> > > +/* Touch reports offsets */
> > > +/* Header offsets */
> > > +#define TOUCH_REPORT_DESC_HDR_CONTACTCOUNT 16
> > > +/* Record offsets */
> > > +#define TOUCH_REPORT_DESC_CONTACTID 8
> > > +#define TOUCH_REPORT_DESC_X 16
> > > +#define TOUCH_REPORT_DESC_Y 32
> > > +#define TOUCH_REPORT_DESC_P 48
> > > +#define TOUCH_REPORT_DESC_MAJ 56
> > > +#define TOUCH_REPORT_DESC_MIN 64
> > > +
> > > +/* HID */
> > > +#define HID_TOUCH_REPORT_ID 0x1
> > > +#define HID_BTN_REPORT_ID 0x3
> > > +#define HID_APP_RESPONSE_REPORT_ID 0x1F
> > > +#define HID_APP_OUTPUT_REPORT_ID 0x2F
> > > +#define HID_BL_RESPONSE_REPORT_ID 0x30
> > > +#define HID_BL_OUTPUT_REPORT_ID 0x40
> > > +
> > > +#define HID_OUTPUT_RESPONSE_REPORT_OFFSET 2
> > > +#define HID_OUTPUT_RESPONSE_CMD_OFFSET 4
> > > +#define HID_OUTPUT_RESPONSE_CMD_MASK 0x7F
> > > +
> > > +#define HID_SYSINFO_SENSING_OFFSET 33
> > > +#define HID_SYSINFO_BTN_OFFSET 48
> > > +#define HID_SYSINFO_BTN_MASK 0xFF
> > > +#define HID_SYSINFO_MAX_BTN 8
> > > +
> > > +/* Timeout in ms */
> > > +#define CY_HID_OUTPUT_TIMEOUT 200
> > > +#define CY_HID_OUTPUT_GET_SYSINFO_TIMEOUT 3000
> > > +#define CY_HID_GET_HID_DESCRIPTOR_TIMEOUT 4000
> > > +
> > > +/* maximum number of concurrent tracks */
> > > +#define TOUCH_REPORT_SIZE 10
> > > +#define TOUCH_INPUT_HEADER_SIZE 7
> > > +#define BTN_REPORT_SIZE 9
> > > +#define BTN_INPUT_HEADER_SIZE 5
> > > +
> > > +/* All usage pages for Touch Report */
> > > +#define TOUCH_REPORT_USAGE_PG_X 0x00010030
> > > +#define TOUCH_REPORT_USAGE_PG_Y 0x00010031
> > > +#define TOUCH_REPORT_USAGE_PG_P 0x000D0030
> > > +#define TOUCH_REPORT_USAGE_PG_CONTACTID 0x000D0051
> > > +#define TOUCH_REPORT_USAGE_PG_CONTACTCOUNT 0x000D0054
> > > +#define TOUCH_REPORT_USAGE_PG_MAJ 0xFF010062
> > > +#define TOUCH_REPORT_USAGE_PG_MIN 0xFF010063
> > > +#define TOUCH_COL_USAGE_PG 0x000D0022
> > > +
> > > +/* helpers */
> > > +#define HI_BYTE(x) (u8)(((x) >> 8) & 0xFF)
> > > +#define LOW_BYTE(x) (u8)((x) & 0xFF)
> > > +
> > > +/* System Information interface definitions */
> > > +struct cyttsp5_sensing_conf_data_dev {
> > > + u8 electrodes_x;
> > > + u8 electrodes_y;
> > > + __le16 len_x;
> > > + __le16 len_y;
> > > + __le16 res_x;
> > > + __le16 res_y;
> > > + __le16 max_z;
> > > + u8 origin_x;
> > > + u8 origin_y;
> > > + u8 btn;
> > > + u8 scan_mode;
> > > + u8 max_num_of_tch_per_refresh_cycle;
> > > +} __packed;
> > > +
> > > +struct cyttsp5_sensing_conf_data {
> > > + u16 res_x;
> > > + u16 res_y;
> > > + u16 max_z;
> > > + u16 len_x;
> > > + u16 len_y;
> > > + u8 origin_x;
> > > + u8 origin_y;
> > > + u8 max_tch;
> > > +};
> > > +
> > > +enum { HID_CMD_DONE, HID_CMD_BUSY } hid_cmd_state;
> > > +
> > > +enum cyttsp5_tch_abs { /* for ordering within the extracted touch data array */
> > > + CY_TCH_X, /* X */
> > > + CY_TCH_Y, /* Y */
> > > + CY_TCH_P, /* P (Z) */
> > > + CY_TCH_T, /* TOUCH ID */
> > > + CY_TCH_MAJ, /* TOUCH_MAJOR */
> > > + CY_TCH_MIN, /* TOUCH_MINOR */
> > > + CY_TCH_NUM_ABS,
> > > +};
> > > +
> > > +struct cyttsp5_tch_abs_params {
> > > + size_t ofs; /* abs byte offset */
> > > + size_t size; /* size in bits */
> > > + size_t min; /* min value */
> > > + size_t max; /* max value */
> > > + size_t bofs; /* bit offset */
> > > +};
> > > +
> > > +struct cyttsp5_touch {
> > > + int hdr;
> > > + int abs[CY_TCH_NUM_ABS];
> > > +};
> > > +
> > > +struct cyttsp5_sysinfo {
> > > + struct cyttsp5_sensing_conf_data sensing_conf_data;
> > > + int num_btns;
> > > + struct cyttsp5_tch_abs_params tch_hdr;
> > > + struct cyttsp5_tch_abs_params tch_abs[CY_TCH_NUM_ABS];
> > > + u32 key_code[HID_SYSINFO_MAX_BTN];
> > > + u8 *xy_mode;
> > > + u8 *xy_data;
> > > +};
> > > +
> > > +struct cyttsp5_hid_desc {
> > > + __le16 hid_desc_len;
> > > + u8 packet_id;
> > > + u8 reserved_byte;
> > > + __le16 bcd_version;
> > > + __le16 report_desc_len;
> > > + __le16 report_desc_register;
> > > + __le16 input_register;
> > > + __le16 max_input_len;
> > > + __le16 output_register;
> > > + __le16 max_output_len;
> > > + __le16 command_register;
> > > + __le16 data_register;
> > > + __le16 vendor_id;
> > > + __le16 product_id;
> > > + __le16 version_id;
> > > + u8 reserved[4];
> > > +} __packed;
> > > +
> > > +struct cyttsp5 {
> > > + struct device *dev;
> > > + struct mutex system_lock;
> > > + wait_queue_head_t wait_q;
> > > + struct cyttsp5_sysinfo sysinfo;
> > > + int hid_cmd_state;
> > > + struct cyttsp5_hid_desc hid_desc;
> > > + u8 cmd_buf[CYTTSP5_PREALLOCATED_CMD_BUFFER];
> > > + u8 input_buf[CY_MAX_INPUT];
> > > + u8 response_buf[CY_MAX_INPUT];
> > > + struct gpio_desc *reset_gpio;
> > > + struct input_dev *input;
> > > + char phys[NAME_MAX];
> > > + int num_prv_rec;
> > > + struct regmap *regmap;
> > > +};
> > > +
> > > +/*
> > > + * For what understood in the datasheet, the register does not
> > > + * matter. For consistency, used the Input Register address
> > > + * but it does mean anything to the device. The important data
> > > + * to send is the I2C address
> > > + */
> > > +static int cyttsp5_read(struct cyttsp5 *ts, u8 *buf, u32 max)
> > > +{
> > > + int rc;
> > > + u32 size;
> > > + u8 temp[2];
> > > +
> > > + if (!buf)
> > > + return -EINVAL;
> >
> > Is it really possible? This is not a publicly facing API but private
> > driver data, do you ever happen to call it with NULL?
>
> hm, I do not think so but I will check that.
>
> >
> > > +
> > > + /* Read the frame to retrieve the size */
> > > + rc = regmap_bulk_read(ts->regmap, HID_INPUT_REG, temp, 2);
> > > + if (rc < 0)
> > > + return rc;
> >
> > Can we call this kind of variables "error" pelase?
>
> Sure.
>
> >
> > > +
> > > + size = get_unaligned_le16(temp);
> > > + if (!size || size == 2)
> > > + return 0;
> > > +
> > > + if (size > max)
> > > + return -EINVAL;
> > > +
> > > + /* Get the real value */
> > > + return regmap_bulk_read(ts->regmap, HID_INPUT_REG, buf, size);
> > > +}
> > > +
> > > +static int cyttsp5_write(struct cyttsp5 *ts, unsigned int reg, u8 *data,
> > > + size_t size)
> > > +{
> > > + u8 cmd[size + 1];
> > > +
> > > + /* High bytes of register address needed as first byte of cmd */
> > > + cmd[0] = HI_BYTE(reg);
> > > +
> > > + /* Copy the rest of the data */
> > > + if (data)
> > > + memcpy(&cmd[1], data, size);
> > > +
> > > + /* The hardware wants to receive a frame with the address register
> >
> > The multiline comment block should start with "/*" on a separate line
> > please.
>
> I will change that.
>
> >
> > > + * contains in the first two bytes. As the regmap_write function
> > > + * add the register adresse in the frame, we use the LOW_BYTE as
> > > + * first frame byte for the address register and the first
> > > + * data byte is the high register + left of the cmd to send
> > > + */
> > > + return regmap_bulk_write(ts->regmap, LOW_BYTE(reg), cmd, size + 1);
> > > +}
> > > +
> > > +static void cyttsp5_final_sync(struct input_dev *input, int max_slots,
> > > + unsigned long *ids)
> > > +{
> > > + int t;
> > > +
> > > + for (t = 0; t < max_slots; t++) {
> >
> > for_each_set_bit() {
> > }
>
> I did not know this macro, I will try that.
>
> >
> > > + if (test_bit(t, ids))
> > > + continue;
> > > + input_mt_slot(input, t);
> > > + input_mt_report_slot_state(input, MT_TOOL_FINGER, false);
> > > + }
> > > +
> > > + input_sync(input);
> > > +}
> > > +
> > > +static void cyttsp5_report_slot_liftoff(struct cyttsp5 *ts, int max_slots)
> > > +{
> > > + int t;
> > > +
> > > + if (ts->num_prv_rec == 0)
> > > + return;
> >
> > Do you need this check? The caller checks the same condition.
>
> True, I will remove it.
>
> >
> > > +
> > > + for (t = 0; t < max_slots; t++) {
> > > + input_mt_slot(ts->input, t);
> > > + input_mt_report_slot_state(ts->input, MT_TOOL_FINGER, false);
> > > + }
> > > +}
> > > +
> > > +static void cyttsp5_mt_lift_all(struct cyttsp5 *ts)
> > > +{
> > > + struct cyttsp5_sysinfo *si = &ts->sysinfo;
> > > + int max = si->tch_abs[CY_TCH_T].max;
> > > +
> > > + if (ts->num_prv_rec != 0) {
> > > + cyttsp5_report_slot_liftoff(ts, max);
> > > + input_sync(ts->input);
> > > + ts->num_prv_rec = 0;
> > > + }
> > > +}
> > > +
> > > +static void cyttsp5_get_touch_axis(int *axis, int size, int max, u8 *xy_data,
> > > + int bofs)
> > > +{
> > > + int nbyte;
> > > + int next;
> > > +
> > > + for (nbyte = 0, *axis = 0, next = 0; nbyte < size; nbyte++)
> > > + *axis = *axis + ((xy_data[nbyte] >> bofs) << (nbyte * 8));
> > > +
> > > + *axis &= max - 1;
> > > +}
> > > +
> > > +static void cyttsp5_get_touch_record(struct cyttsp5 *ts,
> > > + struct cyttsp5_touch *touch, u8 *xy_data)
> > > +{
> > > + struct cyttsp5_sysinfo *si = &ts->sysinfo;
> > > + enum cyttsp5_tch_abs abs;
> > > +
> > > + for (abs = CY_TCH_X; abs < CY_TCH_NUM_ABS; abs++) {
> > > + cyttsp5_get_touch_axis(&touch->abs[abs],
> > > + si->tch_abs[abs].size,
> > > + si->tch_abs[abs].max,
> > > + xy_data + si->tch_abs[abs].ofs,
> > > + si->tch_abs[abs].bofs);
> > > + }
> > > +}
> > > +
> > > +static void cyttsp5_get_mt_touches(struct cyttsp5 *ts,
> > > + struct cyttsp5_touch *tch, int num_cur_tch)
> > > +{
> > > + struct cyttsp5_sysinfo *si = &ts->sysinfo;
> > > + int i, t = 0;
> > > + DECLARE_BITMAP(ids, si->tch_abs[CY_TCH_T].max);
> > > + u8 *tch_addr;
> > > + int tmp;
> > > +
> > > + bitmap_zero(ids, si->tch_abs[CY_TCH_T].max);
> > > + memset(tch->abs, 0, sizeof(tch->abs));
> > > +
> > > + for (i = 0; i < num_cur_tch; i++) {
> > > + tch_addr = si->xy_data + (i * TOUCH_REPORT_SIZE);
> > > + cyttsp5_get_touch_record(ts, tch, tch_addr);
> > > +
> > > + /* Convert MAJOR/MINOR from mm to resolution */
> > > + tmp = tch->abs[CY_TCH_MAJ] * 100 * si->sensing_conf_data.res_x;
> > > + tch->abs[CY_TCH_MAJ] = tmp / si->sensing_conf_data.len_x;
> > > + tmp = tch->abs[CY_TCH_MIN] * 100 * si->sensing_conf_data.res_x;
> > > + tch->abs[CY_TCH_MIN] = tmp / si->sensing_conf_data.len_x;
> > > +
> > > + t = tch->abs[CY_TCH_T];
> > > + input_mt_slot(ts->input, t);
> > > + input_mt_report_slot_state(ts->input, MT_TOOL_FINGER, true);
> > > + __set_bit(t, ids);
> > > +
> > > + /* position and pressure fields */
> > > + input_report_abs(ts->input, ABS_MT_POSITION_X,
> > > + tch->abs[CY_TCH_X]);
> > > + input_report_abs(ts->input, ABS_MT_POSITION_Y,
> > > + tch->abs[CY_TCH_Y]);
> > > + input_report_abs(ts->input, ABS_MT_PRESSURE,
> > > + tch->abs[CY_TCH_P]);
> > > +
> > > + /* Get the extended touch fields */
> > > + input_report_abs(ts->input, ABS_MT_TOUCH_MAJOR,
> > > + tch->abs[CY_TCH_MAJ]);
> > > + input_report_abs(ts->input, ABS_MT_TOUCH_MINOR,
> > > + tch->abs[CY_TCH_MIN]);
> > > + }
> > > +
> > > + cyttsp5_final_sync(ts->input, si->tch_abs[CY_TCH_T].max, ids);
> > > +
> > > + ts->num_prv_rec = num_cur_tch;
> > > +}
> > > +
> > > +/* read xy_data for all current touches */
> > > +static int cyttsp5_xy_worker(struct cyttsp5 *ts)
> > > +{
> > > + struct device *dev = ts->dev;
> > > + struct cyttsp5_sysinfo *si = &ts->sysinfo;
> > > + int max_tch = si->sensing_conf_data.max_tch;
> > > + struct cyttsp5_touch tch;
> > > + u8 num_cur_tch;
> > > +
> > > + cyttsp5_get_touch_axis(&tch.hdr, si->tch_hdr.size,
> > > + si->tch_hdr.max,
> > > + si->xy_mode + 3 + si->tch_hdr.ofs,
> > > + si->tch_hdr.bofs);
> > > +
> > > + num_cur_tch = tch.hdr;
> > > + if (num_cur_tch > max_tch) {
> > > + dev_err(dev, "Num touch err detected (n=%d)\n", num_cur_tch);
> > > + num_cur_tch = max_tch;
> > > + }
> > > +
> > > + if (num_cur_tch == 0 && ts->num_prv_rec == 0)
> > > + return 0;
> > > +
> > > + /* extract xy_data for all currently reported touches */
> > > + if (num_cur_tch)
> > > + cyttsp5_get_mt_touches(ts, &tch, num_cur_tch);
> > > + else
> > > + cyttsp5_mt_lift_all(ts);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int cyttsp5_mt_attention(struct device *dev)
> > > +{
> > > + struct cyttsp5 *ts = dev_get_drvdata(dev);
> >
> > Why don't you pass ts into cyttsp5_mt_attention?
>
> Yep, you are right, I will update it.
>
> >
> > > + struct cyttsp5_sysinfo *si = &ts->sysinfo;
> > > + int rc;
> > > +
> > > + if (si->xy_mode[2] != HID_TOUCH_REPORT_ID)
> > > + return 0;
> > > +
> > > + /* core handles handshake */
> > > + rc = cyttsp5_xy_worker(ts);
> > > + if (rc < 0)
> > > + dev_err(dev, "xy_worker error r=%d\n", rc);
> > > +
> > > + return rc;
> > > +}
> > > +
> > > +static int cyttsp5_setup_input_device(struct device *dev)
> > > +{
> > > + struct cyttsp5 *ts = dev_get_drvdata(dev);
> > > + struct cyttsp5_sysinfo *si = &ts->sysinfo;
> > > + int max_x, max_y, max_p;
> > > + int max_x_tmp, max_y_tmp;
> > > + int rc;
> > > +
> > > + __set_bit(EV_ABS, ts->input->evbit);
> > > + __set_bit(EV_REL, ts->input->evbit);
> > > + __set_bit(EV_KEY, ts->input->evbit);
> > > +
> > > + max_x_tmp = si->sensing_conf_data.res_x;
> > > + max_y_tmp = si->sensing_conf_data.res_y;
> > > + max_x = max_y_tmp - 1;
> > > + max_y = max_x_tmp - 1;
> > > + max_p = si->sensing_conf_data.max_z;
> > > +
> > > + input_mt_init_slots(ts->input, si->tch_abs[CY_TCH_T].max, 0);
> >
> > Error handling.
>
> Thanks.
>
> >
> > > +
> > > + __set_bit(ABS_MT_POSITION_X, ts->input->absbit);
> > > + __set_bit(ABS_MT_POSITION_Y, ts->input->absbit);
> > > + __set_bit(ABS_MT_PRESSURE, ts->input->absbit);
> > > +
> > > + input_set_abs_params(ts->input, ABS_MT_POSITION_X, 0, max_x, 0, 0);
> > > + input_set_abs_params(ts->input, ABS_MT_POSITION_Y, 0, max_y, 0, 0);
> > > + input_set_abs_params(ts->input, ABS_MT_PRESSURE, 0, max_p, 0, 0);
> > > +
> > > + input_set_abs_params(ts->input, ABS_MT_TOUCH_MAJOR, 0, MAX_AREA, 0, 0);
> > > + input_set_abs_params(ts->input, ABS_MT_TOUCH_MINOR, 0, MAX_AREA, 0, 0);
> >
> > You might want to use the standard DT touchscreen properties and
> > reporting functions to support axis inversion and swapping of axes.
>
> Hm, I am not sure to see what you are referring to.
> Could you explain me what you think of?
Please take a look at include/linux/input/touchscreen.h and in the other
driver you are hacking on there is example of how to use this API.
Basically you need to call touchscreen_parse_properties() somewhere in
probe path, and then use touchscreen_report_pos() to report contact
coordinates within given slot.
>
> >
> > > +
> > > + rc = input_register_device(ts->input);
> > > + if (rc < 0)
> > > + dev_err(dev, "Error, failed register input device r=%d\n", rc);
> > > +
> > > + return rc;
> > > +}
> > > +
> > > +#ifdef CONFIG_OF
> > > +static int cyttsp5_parse_dt_key_code(struct device *dev)
> > > +{
> > > + struct cyttsp5 *ts = dev_get_drvdata(dev);
> > > + struct cyttsp5_sysinfo *si = &ts->sysinfo;
> > > + struct device_node *np;
> > > + int i;
> > > +
> > > + np = dev->of_node;
> > > + if (!np)
> > > + return -EINVAL;
> > > +
> > > + if (!si->num_btns)
> > > + return 0;
> > > +
> > > + /* Initialize the button to RESERVED */
> > > + for (i = 0; i < si->num_btns; i++)
> > > + si->key_code[i] = KEY_RESERVED;
> > > +
> > > + return of_property_read_u32_array(np, "linux,keycodes",
> > > + si->key_code, si->num_btns);
> > > +}
> > > +#else
> > > +static int cyttsp5_parse_dt_key_code(struct device *dev)
> > > +{
> > > + struct cyttsp5 *ts = dev_get_drvdata(dev);
> > > + struct cyttsp5_sysinfo *si = &ts->sysinfo;
> > > + int i;
> > > +
> > > + if (!si->num_btns)
> > > + return 0;
> > > +
> > > + /* Initialize the button to RESERVED */
> > > + for (i = 0; i < si->num_btns; i++)
> > > + si->key_code[i] = KEY_RESERVED;
> > > +
> > > + return 0;
> > > +}
> > > +#endif
> > > +
> > > +static int cyttsp5_btn_attention(struct device *dev)
> > > +{
> > > + struct cyttsp5 *ts = dev_get_drvdata(dev);
> > > + struct cyttsp5_sysinfo *si = &ts->sysinfo;
> > > + int cur_btn;
> > > + int cur_btn_state;
> > > +
> > > + if (si->xy_mode[2] != HID_BTN_REPORT_ID || !si->num_btns)
> > > + return 0;
> > > +
> > > + /* extract button press/release touch information */
> > > + for (cur_btn = 0; cur_btn < si->num_btns; cur_btn++) {
> > > + /* Get current button state */
> > > + cur_btn_state = (si->xy_data[0] >> (cur_btn * CY_BITS_PER_BTN))
> > > + & CY_NUM_BTN_EVENT_ID;
> > > +
> > > + input_report_key(ts->input, si->key_code[cur_btn],
> > > + cur_btn_state);
> > > + input_sync(ts->input);
> >
> > You do not need to sen sync after each button, send it once after all
> > buttons sent.
>
> Oh, yes, I will do that!
>
> >
> > > + }
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static u16 cyttsp5_compute_crc(u8 *buf, u32 size)
> > > +{
> > > + u16 remainder = 0xFFFF;
> > > + u16 xor_mask = 0x0000;
> > > + u32 index;
> > > + u32 byte_value;
> > > + u32 table_index;
> > > + u32 crc_bit_width = sizeof(u16) * 8;
> > > +
> > > + /* Divide the message by polynomial, via the table. */
> > > + for (index = 0; index < size; index++) {
> > > + byte_value = buf[index];
> > > + table_index = ((byte_value >> 4) & 0x0F)
> > > + ^ (remainder >> (crc_bit_width - 4));
> > > + remainder = crc_itu_t_table[table_index]
> > > + ^ (remainder << 4);
> > > + table_index = (byte_value & 0x0F)
> > > + ^ (remainder >> (crc_bit_width - 4));
> > > + remainder = crc_itu_t_table[table_index]
> > > + ^ (remainder << 4);
> > > + }
> > > +
> > > + /* Perform the final remainder CRC. */
> > > + return remainder ^ xor_mask;
> > > +}
> > > +
> > > +static int cyttsp5_validate_cmd_response(struct cyttsp5 *ts, u8 code)
> > > +{
> > > + u16 size, crc;
> > > + u8 status, offset;
> > > + int command_code;
> > > +
> > > + size = get_unaligned_le16(&ts->response_buf[0]);
> > > +
> > > + if (!size)
> > > + return 0;
> > > +
> > > + offset = ts->response_buf[HID_OUTPUT_RESPONSE_REPORT_OFFSET];
> > > +
> > > + if (offset == HID_BL_RESPONSE_REPORT_ID) {
> > > + if (ts->response_buf[4] != HID_OUTPUT_BL_SOP) {
> > > + dev_err(ts->dev, "HID output response, wrong SOP\n");
> > > + return -EPROTO;
> > > + }
> > > +
> > > + if (ts->response_buf[size - 1] != HID_OUTPUT_BL_EOP) {
> > > + dev_err(ts->dev, "HID output response, wrong EOP\n");
> > > + return -EPROTO;
> > > + }
> > > +
> > > + crc = cyttsp5_compute_crc(&ts->response_buf[4], size - 7);
> > > + if (ts->response_buf[size - 3] != LOW_BYTE(crc) ||
> > > + ts->response_buf[size - 2] != HI_BYTE(crc)) {
> > > + dev_err(ts->dev, "HID output response, wrong CRC 0x%X\n",
> > > + crc);
> > > + return -EPROTO;
> > > + }
> > > +
> > > + status = ts->response_buf[5];
> > > + if (status) {
> > > + dev_err(ts->dev, "HID output response, ERROR:%d\n",
> > > + status);
> > > + return -EPROTO;
> > > + }
> > > + }
> > > +
> > > + if (offset == HID_APP_RESPONSE_REPORT_ID) {
> > > + command_code = ts->response_buf[HID_OUTPUT_RESPONSE_CMD_OFFSET]
> > > + & HID_OUTPUT_RESPONSE_CMD_MASK;
> > > + if (command_code != code) {
> > > + dev_err(ts->dev,
> > > + "HID output response, wrong command_code:%X\n",
> > > + command_code);
> > > + return -EPROTO;
> > > + }
> > > + }
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static void cyttsp5_si_get_btn_data(struct cyttsp5 *ts)
> > > +{
> > > + struct cyttsp5_sysinfo *si = &ts->sysinfo;
> > > + int i;
> > > + unsigned int btns = ts->response_buf[HID_SYSINFO_BTN_OFFSET]
> > > + & HID_SYSINFO_BTN_MASK;
> > > +
> > > + si->num_btns = 0;
> > > + for (i = 0; i < HID_SYSINFO_MAX_BTN; i++) {
> > > + if (btns & BIT(i))
> > > + si->num_btns++;
> > > + }
> >
> > si->num_btns = hweight8(ts->response_buf[HID_SYSINFO_BTN_OFFSET]);
>
> Great, I will try that!
>
> >
> > > +}
> > > +
> > > +static int cyttsp5_get_sysinfo_regs(struct cyttsp5 *ts)
> > > +{
> > > + struct cyttsp5_sensing_conf_data *scd = &ts->sysinfo.sensing_conf_data;
> > > + struct cyttsp5_sensing_conf_data_dev *scd_dev =
> > > + (struct cyttsp5_sensing_conf_data_dev *)
> > > + &ts->response_buf[HID_SYSINFO_SENSING_OFFSET];
> > > + struct cyttsp5_sysinfo *si = &ts->sysinfo;
> > > +
> > > + cyttsp5_si_get_btn_data(ts);
> > > +
> > > + scd->max_tch = scd_dev->max_num_of_tch_per_refresh_cycle;
> > > + scd->res_x = get_unaligned_le16(&scd_dev->res_x);
> > > + scd->res_y = get_unaligned_le16(&scd_dev->res_y);
> > > + scd->max_z = get_unaligned_le16(&scd_dev->max_z);
> > > + scd->len_x = get_unaligned_le16(&scd_dev->len_x);
> > > + scd->len_y = get_unaligned_le16(&scd_dev->len_y);
> > > +
> > > + si->xy_data = devm_kzalloc(ts->dev, scd->max_tch * TOUCH_REPORT_SIZE,
> > > + GFP_KERNEL);
> > > + if (!si->xy_data)
> > > + return -ENOMEM;
> > > +
> > > + si->xy_mode = devm_kzalloc(ts->dev, TOUCH_INPUT_HEADER_SIZE,
> > > + GFP_KERNEL);
> > > + if (!si->xy_mode)
> > > + return -ENOMEM;
> >
> > Why do we need these 2 allocated separately form the driver data?
>
> xy_mode and particularly xy_data are used to retrieve buttons or touch
> data that we received from the input buffer (see gggggggggggggggg()
> and move_touch_data()). I guess that I can try to remove them, if you
> want.
You probably do not need them, you already have all data in input_buf,
just the right offset to cyttsp5_btn_attention() , like
...
cyttsp5_btn_attention(ts, ts->input_buf + BTN_INPUT_HEADER_SIZE);
...
>
> >
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int cyttsp5_hid_output_get_sysinfo(struct cyttsp5 *ts)
> > > +{
> > > + int rc;
> > > + u8 cmd[HID_OUTPUT_GET_SYSINFO_SIZE];
> > > +
> > > + ts->hid_cmd_state = HID_CMD_BUSY;
> > > +
> > > + /* HI bytes of Output register address */
> > > + cmd[0] = LOW_BYTE(HID_OUTPUT_GET_SYSINFO_SIZE);
> > > + cmd[1] = HI_BYTE(HID_OUTPUT_GET_SYSINFO_SIZE);
> > > + cmd[2] = HID_APP_OUTPUT_REPORT_ID;
> > > + cmd[3] = 0x0; /* Reserved */
> > > + cmd[4] = HID_OUTPUT_GET_SYSINFO;
> > > +
> > > + rc = cyttsp5_write(ts, HID_OUTPUT_REG, cmd,
> > > + HID_OUTPUT_GET_SYSINFO_SIZE);
> > > + if (rc) {
> > > + dev_err(ts->dev, "Failed to write command %d", rc);
> > > + goto error;
> > > + }
> > > +
> > > + rc = wait_event_timeout(ts->wait_q, (ts->hid_cmd_state == HID_CMD_DONE),
> > > + msecs_to_jiffies(CY_HID_OUTPUT_GET_SYSINFO_TIMEOUT));
> > > + if (!rc) {
> > > + dev_err(ts->dev, "HID output cmd execution timed out\n");
> > > + rc = -ETIME;
> > > + goto error;
> > > + }
> > > +
> > > + rc = cyttsp5_validate_cmd_response(ts, HID_OUTPUT_GET_SYSINFO);
> > > + if (rc) {
> > > + dev_err(ts->dev, "Validation of the response failed\n");
> > > + goto error;
> > > + }
> > > +
> > > + return cyttsp5_get_sysinfo_regs(ts);
> > > +
> > > +error:
> > > + mutex_lock(&ts->system_lock);
> > > + ts->hid_cmd_state = HID_CMD_DONE;
> > > + mutex_unlock(&ts->system_lock);
> > > + return rc;
> > > +}
> > > +
> > > +static int cyttsp5_hid_output_bl_launch_app(struct cyttsp5 *ts)
> > > +{
> > > + int rc;
> > > + u8 cmd[HID_OUTPUT_BL_LAUNCH_APP];
> > > + u16 crc;
> > > +
> > > + mutex_lock(&ts->system_lock);
> > > + ts->hid_cmd_state = HID_CMD_BUSY;
> > > + mutex_unlock(&ts->system_lock);
> > > +
> > > + cmd[0] = LOW_BYTE(HID_OUTPUT_BL_LAUNCH_APP_SIZE);
> > > + cmd[1] = HI_BYTE(HID_OUTPUT_BL_LAUNCH_APP_SIZE);
> > > + cmd[2] = HID_BL_OUTPUT_REPORT_ID;
> > > + cmd[3] = 0x0; /* Reserved */
> > > + cmd[4] = HID_OUTPUT_BL_SOP;
> > > + cmd[5] = HID_OUTPUT_BL_LAUNCH_APP;
> > > + cmd[6] = 0x0; /* Low bytes of data */
> > > + cmd[7] = 0x0; /* Hi bytes of data */
> > > + crc = cyttsp5_compute_crc(&cmd[4], 4);
> > > + cmd[8] = LOW_BYTE(crc);
> > > + cmd[9] = HI_BYTE(crc);
> > > + cmd[10] = HID_OUTPUT_BL_EOP;
> > > +
> > > + rc = cyttsp5_write(ts, HID_OUTPUT_REG, cmd,
> > > + HID_OUTPUT_BL_LAUNCH_APP_SIZE);
> > > + if (rc) {
> > > + dev_err(ts->dev, "Failed to write command %d", rc);
> > > + goto error;
> > > + }
> > > +
> > > + rc = wait_event_timeout(ts->wait_q, (ts->hid_cmd_state == HID_CMD_DONE),
> > > + msecs_to_jiffies(CY_HID_OUTPUT_TIMEOUT));
> > > + if (!rc) {
> > > + dev_err(ts->dev, "HID output cmd execution timed out\n");
> > > + rc = -ETIME;
> > > + goto error;
> > > + }
> > > +
> > > + rc = cyttsp5_validate_cmd_response(ts, HID_OUTPUT_BL_LAUNCH_APP);
> > > + if (rc) {
> > > + dev_err(ts->dev, "Validation of the response failed\n");
> > > + goto error;
> > > + }
> > > +
> > > + return rc;
> > > +
> > > +error:
> > > + mutex_lock(&ts->system_lock);
> > > + ts->hid_cmd_state = HID_CMD_DONE;
> > > + mutex_unlock(&ts->system_lock);
> > > +
> > > + return rc;
> > > +}
> > > +
> > > +static int cyttsp5_get_hid_descriptor(struct cyttsp5 *ts,
> > > + struct cyttsp5_hid_desc *desc)
> > > +{
> > > + struct device *dev = ts->dev;
> > > + __le16 hid_desc_register = HID_DESC_REG;
> > > + int rc;
> > > + u8 cmd[2];
> > > +
> > > + /* Read HID descriptor length and version */
> > > + mutex_lock(&ts->system_lock);
> > > + ts->hid_cmd_state = HID_CMD_BUSY;
> > > + mutex_unlock(&ts->system_lock);
> > > +
> > > + /* Set HID descriptor register */
> > > + memcpy(cmd, &hid_desc_register, sizeof(hid_desc_register));
> > > +
> > > + rc = cyttsp5_write(ts, HID_DESC_REG, NULL, 0);
> > > + if (rc < 0) {
> > > + dev_err(dev, "Failed to get HID descriptor, rc=%d\n", rc);
> > > + goto error;
> > > + }
> > > +
> > > + rc = wait_event_timeout(ts->wait_q, (ts->hid_cmd_state == HID_CMD_DONE),
> > > + msecs_to_jiffies(CY_HID_GET_HID_DESCRIPTOR_TIMEOUT));
> > > + if (!rc) {
> > > + dev_err(ts->dev, "HID get descriptor timed out\n");
> > > + rc = -ETIME;
> > > + goto error;
> > > + }
> > > +
> > > + memcpy(desc, ts->response_buf, sizeof(struct cyttsp5_hid_desc));
> > > +
> > > + /* Check HID descriptor length and version */
> > > + if (le16_to_cpu(desc->hid_desc_len) != sizeof(*desc) ||
> > > + le16_to_cpu(desc->bcd_version) != HID_VERSION) {
> > > + dev_err(dev, "Unsupported HID version\n");
> > > + return -ENODEV;
> > > + }
> > > +
> > > + goto exit;
> > > +
> > > +error:
> > > + mutex_lock(&ts->system_lock);
> > > + ts->hid_cmd_state = HID_CMD_DONE;
> > > + mutex_unlock(&ts->system_lock);
> > > +exit:
> > > + return rc;
> > > +}
> > > +
> > > +static int fill_tch_abs(struct cyttsp5_tch_abs_params *tch_abs, int report_size,
> > > + int offset)
> > > +{
> > > + tch_abs->ofs = offset / 8;
> > > + tch_abs->size = report_size / 8;
> > > + if (report_size % 8)
> > > + tch_abs->size += 1;
> > > + tch_abs->min = 0;
> > > + tch_abs->max = 1 << report_size;
> > > + tch_abs->bofs = offset - (tch_abs->ofs << 3);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int move_button_data(struct cyttsp5 *ts, struct cyttsp5_sysinfo *si)
> > > +{
> > > + memcpy(si->xy_mode, ts->input_buf, BTN_INPUT_HEADER_SIZE);
> > > + memcpy(si->xy_data, &ts->input_buf[BTN_INPUT_HEADER_SIZE],
> > > + BTN_REPORT_SIZE);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int move_touch_data(struct cyttsp5 *ts, struct cyttsp5_sysinfo *si)
> > > +{
> > > + int max_tch = si->sensing_conf_data.max_tch;
> > > + int num_cur_tch;
> > > + int length;
> > > + struct cyttsp5_tch_abs_params *tch = &si->tch_hdr;
> > > +
> > > + memcpy(si->xy_mode, ts->input_buf, TOUCH_INPUT_HEADER_SIZE);
> > > +
> > > + cyttsp5_get_touch_axis(&num_cur_tch, tch->size,
> > > + tch->max, si->xy_mode + 3 + tch->ofs, tch->bofs);
> > > + if (unlikely(num_cur_tch > max_tch))
> > > + num_cur_tch = max_tch;
> > > +
> > > + length = num_cur_tch * TOUCH_REPORT_SIZE;
> > > +
> > > + memcpy(si->xy_data, &ts->input_buf[TOUCH_INPUT_HEADER_SIZE], length);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static irqreturn_t cyttsp5_handle_irq(int irq, void *handle)
> > > +{
> > > + struct cyttsp5 *ts = handle;
> > > + int report_id;
> > > + int size;
> > > + int rc;
> > > +
> > > + rc = cyttsp5_read(ts, ts->input_buf, CY_MAX_INPUT);
> > > + if (rc)
> > > + return IRQ_HANDLED;
> > > +
> > > + size = get_unaligned_le16(&ts->input_buf[0]);
> > > +
> > > + /* check reset */
> > > + if (size == 0) {
> > > + memcpy(ts->response_buf, ts->input_buf, 2);
> > > +
> > > + mutex_lock(&ts->system_lock);
> > > + ts->hid_cmd_state = HID_CMD_DONE;
> > > + mutex_unlock(&ts->system_lock);
> > > + wake_up(&ts->wait_q);
> >
> > I'd use spinlock in wait queue and wake_up_locked() instead of a
> > separate mutex.
>
> Hum, okay, I will try that.
>
> >
> > > + return IRQ_HANDLED;
> > > + }
> > > +
> > > + report_id = ts->input_buf[2];
> > > +
> >
> > switch(report_id) {
> > }
>
> Yep, it will be easier to understand.
>
> >
> > > + if (report_id == HID_TOUCH_REPORT_ID) {
> > > + move_touch_data(ts, &ts->sysinfo);
> > > + cyttsp5_mt_attention(ts->dev);
> > > + } else if (report_id == HID_BTN_REPORT_ID) {
> > > + move_button_data(ts, &ts->sysinfo);
> > > + cyttsp5_btn_attention(ts->dev);
> > > + } else {
> > > + /* It is not an input but a command response */
> > > + memcpy(ts->response_buf, ts->input_buf, size);
> > > +
> > > + mutex_lock(&ts->system_lock);
> > > + ts->hid_cmd_state = HID_CMD_DONE;
> > > + mutex_unlock(&ts->system_lock);
> > > + wake_up(&ts->wait_q);
> > > + }
> > > +
> > > + return IRQ_HANDLED;
> > > +}
> > > +
> > > +static int cyttsp5_deassert_int(struct cyttsp5 *ts)
> > > +{
> > > + u16 size;
> > > + u8 buf[2];
> > > + int rc;
> > > +
> > > + rc = regmap_bulk_read(ts->regmap, HID_INPUT_REG, buf, 2);
> > > + if (rc < 0)
> > > + return rc;
> > > +
> > > + size = get_unaligned_le16(&buf[0]);
> > > + if (size == 2 || size == 0)
> > > + return 0;
> > > +
> > > + return -EINVAL;
> > > +}
> > > +
> > > +static int cyttsp5_fill_all_touch(struct cyttsp5 *ts)
> > > +{
> > > + struct cyttsp5_sysinfo *si = &ts->sysinfo;
> > > +
> > > + fill_tch_abs(&si->tch_abs[CY_TCH_X], REPORT_SIZE_16,
> > > + TOUCH_REPORT_DESC_X);
> > > + fill_tch_abs(&si->tch_abs[CY_TCH_Y], REPORT_SIZE_16,
> > > + TOUCH_REPORT_DESC_Y);
> > > + fill_tch_abs(&si->tch_abs[CY_TCH_P], REPORT_SIZE_8,
> > > + TOUCH_REPORT_DESC_P);
> > > + fill_tch_abs(&si->tch_abs[CY_TCH_T], REPORT_SIZE_5,
> > > + TOUCH_REPORT_DESC_CONTACTID);
> > > + fill_tch_abs(&si->tch_hdr, REPORT_SIZE_5,
> > > + TOUCH_REPORT_DESC_HDR_CONTACTCOUNT);
> > > + fill_tch_abs(&si->tch_abs[CY_TCH_MAJ], REPORT_SIZE_8,
> > > + TOUCH_REPORT_DESC_MAJ);
> > > + fill_tch_abs(&si->tch_abs[CY_TCH_MIN], REPORT_SIZE_8,
> > > + TOUCH_REPORT_DESC_MIN);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int cyttsp5_startup(struct cyttsp5 *ts)
> > > +{
> > > + int rc;
> > > +
> > > + rc = cyttsp5_deassert_int(ts);
> > > + if (rc) {
> > > + dev_err(ts->dev, "Error on deassert int r=%d\n", rc);
> > > + return -ENODEV;
> > > + }
> > > +
> > > + /*
> > > + * Launch the application as the device starts in bootloader mode
> > > + * because of a power-on-reset
> > > + */
> > > + rc = cyttsp5_hid_output_bl_launch_app(ts);
> > > + if (rc < 0) {
> > > + dev_err(ts->dev, "Error on launch app r=%d\n", rc);
> > > + return rc;
> > > + }
> > > +
> > > + rc = cyttsp5_get_hid_descriptor(ts, &ts->hid_desc);
> > > + if (rc < 0) {
> > > + dev_err(ts->dev, "Error on getting HID descriptor r=%d\n", rc);
> > > + return rc;
> > > + }
> > > +
> > > + rc = cyttsp5_fill_all_touch(ts);
> > > + if (rc < 0) {
> > > + dev_err(ts->dev, "Error on report descriptor r=%d\n", rc);
> > > + return rc;
> > > + }
> > > +
> > > + rc = cyttsp5_hid_output_get_sysinfo(ts);
> > > + if (rc) {
> > > + dev_err(ts->dev, "Error on getting sysinfo r=%d\n", rc);
> > > + return rc;
> > > + }
> > > +
> > > + return rc;
> > > +}
> > > +
> > > +#ifdef CONFIG_OF
> > > +static const struct of_device_id cyttsp5_of_match[] = {
> > > + { .compatible = "cypress,cyttsp5", },
> > > + { }
> > > +};
> > > +MODULE_DEVICE_TABLE(of, cyttsp5_of_match);
> > > +#endif
> > > +
> > > +static const struct i2c_device_id cyttsp5_i2c_id[] = {
> > > + { CYTTSP5_NAME, 0, },
> > > + { }
> > > +};
> > > +MODULE_DEVICE_TABLE(i2c, cyttsp5_i2c_id);
> > > +
> > > +static int cyttsp5_probe(struct device *dev, struct regmap *regmap, int irq,
> > > + const char *name)
> > > +{
> > > + struct cyttsp5 *ts;
> > > + struct cyttsp5_sysinfo *si;
> > > + int rc = 0, i;
> > > +
> > > + ts = devm_kzalloc(dev, sizeof(*ts), GFP_KERNEL);
> > > + if (!ts)
> > > + return -ENOMEM;
> > > +
> > > + /* Initialize device info */
> > > + ts->regmap = regmap;
> > > + ts->dev = dev;
> > > + si = &ts->sysinfo;
> > > + dev_set_drvdata(dev, ts);
> > > +
> > > + /* Initialize mutexes and spinlocks */
> > > + mutex_init(&ts->system_lock);
> > > +
> > > + /* Initialize wait queue */
> > > + init_waitqueue_head(&ts->wait_q);
> > > +
> > > + /* Reset the gpio to be in a reset state */
> > > + ts->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
> > > + if (IS_ERR(ts->reset_gpio)) {
> > > + rc = PTR_ERR(ts->reset_gpio);
> > > + dev_err(dev, "Failed to request reset gpio, error %d\n", rc);
> > > + return rc;
> > > + }
> > > + gpiod_set_value(ts->reset_gpio, 1);
> >
> > Why not request it as GPIOD_OUT_HIGH if you going to activate it
> > immediately? However it sounds as if you have a reset line that is
> > active low and you want to driver it low to reset, and then release. In
> > this case you need to do
> >
> > ts->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
> > <delay> - chip usually needs to be some time in reset state
> > gpiod_set_value(ts->reset_gpio, 0);
> >
> > and make sure that correct polarity is specified in device tree.
>
> Okay, I will update it too.
>
> >
> > > +
> > > + /* Need a delay to have device up */
> > > + msleep(20);
> > > +
> > > + rc = devm_request_threaded_irq(dev, irq, NULL, cyttsp5_handle_irq,
> > > + IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
> >
> > Just use IRQF_ONESHOT and make sure DTS specifies interrupt properly.
> > BTW,I'd recommend using level, not edge interrupts. It is so easy to
> > miss an edge.
>
> Okay, thank you for the advice.
>
> >
> > > + name, ts);
> > > + if (rc) {
> > > + dev_err(dev, "unable to request IRQ\n");
> > > + return rc;
> > > + }
> > > +
> > > + rc = cyttsp5_startup(ts);
> > > + if (rc) {
> > > + dev_err(ts->dev, "Fail initial startup r=%d\n", rc);
> > > + return rc;
> > > + }
> > > +
> > > + rc = cyttsp5_parse_dt_key_code(dev);
> > > + if (rc < 0) {
> > > + dev_err(ts->dev, "Error while parsing dts %d\n", rc);
> > > + return rc;
> > > + }
> > > +
> > > + ts->input = devm_input_allocate_device(dev);
> > > + if (!ts->input) {
> > > + dev_err(dev, "Error, failed to allocate input device\n");
> > > + return -ENODEV;
> > > + }
> > > +
> > > + ts->input->name = "cyttsp5";
> > > + scnprintf(ts->phys, sizeof(ts->phys), "%s/input0", dev_name(dev));
> > > + ts->input->phys = ts->phys;
> > > + ts->input->dev.parent = ts->dev;
> > > + input_set_drvdata(ts->input, ts);
> > > +
> > > + touchscreen_parse_properties(ts->input, true, NULL);
> > > +
> > > + __set_bit(EV_KEY, ts->input->evbit);
> > > + for (i = 0; i < si->num_btns; i++)
> > > + __set_bit(si->key_code[i], ts->input->keybit);
> > > +
> > > + return cyttsp5_setup_input_device(dev);
> > > +}
> > > +
> > > +static int cyttsp5_i2c_probe(struct i2c_client *client,
> > > + const struct i2c_device_id *id)
> > > +{
> > > + struct regmap *regmap;
> > > + static const struct regmap_config config = {
> > > + .reg_bits = 8,
> > > + .val_bits = 8,
> > > + };
> > > +
> > > + regmap = devm_regmap_init_i2c(client, &config);
> > > + if (IS_ERR(regmap)) {
> > > + dev_err(&client->dev, "regmap allocation failed: %ld\n",
> > > + PTR_ERR(regmap));
> > > + return PTR_ERR(regmap);
> > > + }
> > > +
> > > + return cyttsp5_probe(&client->dev, regmap, client->irq, client->name);
> > > +}
> > > +
> > > +static int cyttsp5_remove(struct device *dev)
> > > +{
> > > + struct cyttsp5 *ts = dev_get_drvdata(dev);
> > > +
> > > + input_unregister_device(ts->input);
> >
> > Not needed: you are using managed input device.
>
> You are right, thanks.
>
> >
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int cyttsp5_i2c_remove(struct i2c_client *client)
> > > +{
> > > + struct device *dev = &client->dev;
> > > +
> > > + return cyttsp5_remove(dev);
> >
> > Not needed if you remove cyttsp5_remove().
>
> Sure.
>
> >
> > > +}
> > > +
> > > +static struct i2c_driver cyttsp5_i2c_driver = {
> > > + .driver = {
> > > + .name = CYTTSP5_NAME,
> > > + .owner = THIS_MODULE,
> > > + .of_match_table = of_match_ptr(cyttsp5_of_match),
> > > + },
> > > + .probe = cyttsp5_i2c_probe,
> > > + .remove = cyttsp5_i2c_remove,
> > > + .id_table = cyttsp5_i2c_id,
> > > +};
> > > +
> > > +module_i2c_driver(cyttsp5_i2c_driver);
> > > +
> > > +MODULE_LICENSE("GPL");
> > > +MODULE_DESCRIPTION("Touchscreen driver for Cypress TrueTouch Gen 5 Product");
> > > +MODULE_AUTHOR("Mylène Josserand <mylene.josserand@xxxxxxxxxxxxxxxxxx>");
> > > --
> > > 2.11.0
> > >
> >
> > Thanks.
> >
>
> Best regards,
>
> --
> Mylène Josserand, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
>
--
Dmitry