Re: [linux-sunxi] [PATCH 2/3] arm64: allwinner: h6: add device tree nodes for MMC controllers

[Andre Przywara]

Hi,

On 26/04/18 15:07, Icenowy Zheng wrote:
> The Allwinner H6 SoC have 3 MMC controllers.
> 
> Add device tree nodes for them.
> 
> Signed-off-by: Icenowy Zheng <icenowy@xxxxxxx>
> ---
>  arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 56 ++++++++++++++++++++++++++++
>  1 file changed, 56 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
> index 4debc3962830..3cbfc035c979 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
> @@ -124,12 +124,68 @@
>  			interrupt-controller;
>  			#interrupt-cells = <3>;
>  
> +			mmc0_pins: mmc0-pins {
> +				pins = "PF0", "PF1", "PF2", "PF3",
> +				       "PF4", "PF5";
> +				function = "mmc0";
> +				drive-strength = <30>;
> +				bias-pull-up;
> +			};
> +
> +			mmc2_pins: mmc2-pins {
> +				pins = "PC1", "PC4", "PC5", "PC6",
> +				       "PC7", "PC8", "PC9", "PC10",
> +				       "PC11", "PC12", "PC13", "PC14";
> +				function = "mmc2";
> +				drive-strength = <30>;
> +				bias-pull-up;
> +			};
> +
>  			uart0_ph_pins: uart0-ph {
>  				pins = "PH0", "PH1";
>  				function = "uart0";
>  			};
>  		};
>  
> +		mmc0: mmc@4020000 {
> +			compatible = "allwinner,sun50i-h6-mmc";

This should be:
			compatible = "allwinner,sun50i-h6-mmc",
				     "allwinner,sun50i-a64-mmc";

> +			reg = <0x04020000 0x1000>;
> +			clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
> +			clock-names = "ahb", "mmc";
> +			resets = <&ccu RST_BUS_MMC0>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		mmc1: mmc@4021000 {
> +			compatible = "allwinner,sun50i-h6-mmc";

same here

> +			reg = <0x04021000 0x1000>;
> +			clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
> +			clock-names = "ahb", "mmc";
> +			resets = <&ccu RST_BUS_MMC1>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		mmc2: mmc@4022000 {
> +			compatible = "allwinner,sun50i-h6-emmc";

and here:
			compatible = "allwinner,sun50i-h6-emmc",
				     "allwinner,sun50i-a64-emmc";

The rest looks correct to me.

Cheers,
Andre.

> +			reg = <0x04022000 0x1000>;
> +			clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
> +			clock-names = "ahb", "mmc";
> +			resets = <&ccu RST_BUS_MMC2>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
>  		uart0: serial@5000000 {
>  			compatible = "snps,dw-apb-uart";
>  			reg = <0x05000000 0x400>;
>