[PATCH v5 4/6] mfd: cros-ec: Introduce CEC commands and events definitions.

From: Neil Armstrong
Date: Thu May 24 2018 - 04:02:33 EST


The EC can expose a CEC bus, this patch adds the CEC related definitions
needed by the cros-ec-cec driver.

Signed-off-by: Neil Armstrong <narmstrong@xxxxxxxxxxxx>
Tested-by: Enric Balletbo i Serra <enric.balletbo@xxxxxxxxxxxxx>
---
include/linux/mfd/cros_ec_commands.h | 85 ++++++++++++++++++++++++++++++++++++
1 file changed, 85 insertions(+)

diff --git a/include/linux/mfd/cros_ec_commands.h b/include/linux/mfd/cros_ec_commands.h
index cc0768e..ea9646f 100644
--- a/include/linux/mfd/cros_ec_commands.h
+++ b/include/linux/mfd/cros_ec_commands.h
@@ -804,6 +804,8 @@ enum ec_feature_code {
EC_FEATURE_MOTION_SENSE_FIFO = 24,
/* EC has RTC feature that can be controlled by host commands */
EC_FEATURE_RTC = 27,
+ /* EC supports CEC commands */
+ EC_FEATURE_CEC = 35,
};

#define EC_FEATURE_MASK_0(event_code) (1UL << (event_code % 32))
@@ -2078,6 +2080,12 @@ enum ec_mkbp_event {
/* EC sent a sysrq command */
EC_MKBP_EVENT_SYSRQ = 6,

+ /* Notify the AP that something happened on CEC */
+ EC_MKBP_CEC_EVENT = 8,
+
+ /* Send an incoming CEC message to the AP */
+ EC_MKBP_EVENT_CEC_MESSAGE = 9,
+
/* Number of MKBP events */
EC_MKBP_EVENT_COUNT,
};
@@ -2850,6 +2858,83 @@ struct ec_params_reboot_ec {

/*****************************************************************************/
/*
+ * HDMI CEC commands
+ *
+ * These commands are for sending and receiving message via HDMI CEC
+ */
+#define MAX_CEC_MSG_LEN 16
+
+/* CEC message from the AP to be written on the CEC bus */
+#define EC_CMD_CEC_WRITE_MSG 0x00B8
+
+/**
+ * struct ec_params_cec_write - Message to write to the CEC bus
+ * @msg: message content to write to the CEC bus
+ */
+struct ec_params_cec_write {
+ uint8_t msg[MAX_CEC_MSG_LEN];
+} __packed;
+
+/* Set various CEC parameters */
+#define EC_CMD_CEC_SET 0x00BA
+
+/**
+ * struct ec_params_cec_set - CEC parameters set
+ * @cmd: parameter type, can be CEC_CMD_ENABLE or CEC_CMD_LOGICAL_ADDRESS
+ * @enable: in case cmd is CEC_CMD_ENABLE, this field can be 0 to disable CEC
+ * or 1 to enable CEC functionnality
+ * @address: in case cmd is CEC_CMD_LOGICAL_ADDRESS, this field encodes the
+ * requested logical address between 0 and 15 or 0xff to unregister
+ */
+struct ec_params_cec_set {
+ uint8_t cmd; /* enum cec_command */
+ union {
+ uint8_t enable;
+ uint8_t address;
+ };
+} __packed;
+
+/* Read various CEC parameters */
+#define EC_CMD_CEC_GET 0x00BB
+
+/**
+ * struct ec_params_cec_get - CEC parameters get
+ * @cmd: parameter type, can be CEC_CMD_ENABLE or CEC_CMD_LOGICAL_ADDRESS
+ */
+struct ec_params_cec_get {
+ uint8_t cmd; /* enum cec_command */
+} __packed;
+
+/**
+ * struct ec_response_cec_get - CEC parameters get response
+ * @enable: in case cmd was CEC_CMD_ENABLE, this field will 0 if CEC is
+ * disabled or 1 if CEC functionnality is enabled
+ * @address: in case cmd was CEC_CMD_LOGICAL_ADDRESS, this will encode the
+ * configured logical address between 0 and 15 or 0xff if unregistered
+ */
+struct ec_response_cec_get {
+ union {
+ uint8_t enable;
+ uint8_t address;
+ };
+} __packed;
+
+/* CEC parameters command */
+enum cec_command {
+ /* CEC reading, writing and events enable */
+ CEC_CMD_ENABLE,
+ /* CEC logical address */
+ CEC_CMD_LOGICAL_ADDRESS,
+};
+
+/* Events from CEC to AP */
+enum mkbp_cec_event {
+ EC_MKBP_CEC_SEND_OK = BIT(0),
+ EC_MKBP_CEC_SEND_FAILED = BIT(1),
+};
+
+/*****************************************************************************/
+/*
* Special commands
*
* These do not follow the normal rules for commands. See each command for
--
2.7.4