[PATCH 11/20] staging:rtl8192u: Remove unused page-8 Bit Mask definitions - Style

[John Whitmore]

Remove unused 'page-8' Bit Mask definitions. These definitions fail the
checkpatch CamelCase naming test, since they are unused in code they have
simply been removed from code, rather then renamed. This is a coding
style change which should not impact runtime code execution.
 * page-8
 */

Signed-off-by: John Whitmore <johnfwhitmore@xxxxxxxxx>
---
 drivers/staging/rtl8192u/r819xU_phyreg.h | 114 -----------------------
 1 file changed, 114 deletions(-)

diff --git a/drivers/staging/rtl8192u/r819xU_phyreg.h b/drivers/staging/rtl8192u/r819xU_phyreg.h
index fb0b388f6759..211f34359e43 100644
--- a/drivers/staging/rtl8192u/r819xU_phyreg.h
+++ b/drivers/staging/rtl8192u/r819xU_phyreg.h
@@ -108,131 +108,17 @@
  * page-8
  */
 #define bRFMOD						0x1
-#define bJapanMode				0x2
-#define bCCKTxSC					0x30
 #define bCCKEn						0x1000000
 #define bOFDMEn						0x2000000
-#define bOFDMRxADCPhase				0x10000
-#define bOFDMTxDACPhase				0x40000
-#define bXATxAGC					0x3f
 #define bXBTxAGC					0xf00
 #define bXCTxAGC					0xf000
-#define bXDTxAGC					0xf0000
-#define bPAStart					0xf0000000
-#define bTRStart					0x00f00000
-#define bRFStart					0x0000f000
-#define bBBStart					0x000000f0
-#define bBBCCKStart				0x0000000f
-#define bPAEnd						0xf     /* Reg0x814 */
-#define bTREnd						0x0f000000
-#define bRFEnd						0x000f0000
-#define bCCAMask					0x000000f0   /* T2R */
-#define bR2RCCAMask				0x00000f00
-#define bHSSI_R2TDelay				0xf8000000
-#define bHSSI_T2RDelay				0xf80000
-#define bContTxHSSI				0x400     /* chane gain at continue Tx */
-#define bIGFromCCK				0x200
-#define bAGCAddress				0x3f
-#define bRxHPTx						0x7000
-#define bRxHPT2R					0x38000
-#define bRxHPCCKIni				0xc0000
-#define bAGCTxCode				0xc00000
-#define bAGCRxCode				0x300000
 #define b3WireDataLength			0x800
 #define b3WireAddressLength			0x400
-#define b3WireRFPowerDown			0x1
-/* #define bHWSISelect				0x8 */
-#define b5GPAPEPolarity				0x40000000
-#define b2GPAPEPolarity				0x80000000
-#define bRFSW_TxDefaultAnt			0x3
-#define bRFSW_TxOptionAnt			0x30
-#define bRFSW_RxDefaultAnt			0x300
-#define bRFSW_RxOptionAnt			0x3000
-#define bRFSI_3WireData				0x1
-#define bRFSI_3WireClock			0x2
-#define bRFSI_3WireLoad				0x4
-#define bRFSI_3WireRW				0x8
-#define bRFSI_3Wire					0xf  /* 3-wire total control */
 #define bRFSI_RFENV				0x10
-#define bRFSI_TRSW				0x20
-#define bRFSI_TRSWB				0x40
-#define bRFSI_ANTSW				0x100
-#define bRFSI_ANTSWB				0x200
-#define bRFSI_PAPE					0x400
-#define bRFSI_PAPE5G				0x800
-#define bBandSelect					0x1
-#define bHTSIG2_GI					0x80
-#define bHTSIG2_Smoothing			0x01
-#define bHTSIG2_Sounding			0x02
-#define bHTSIG2_Aggreaton			0x08
-#define bHTSIG2_STBC				0x30
-#define bHTSIG2_AdvCoding			0x40
-#define bHTSIG2_NumOfHTLTF		0x300
-#define bHTSIG2_CRC8				0x3fc
-#define bHTSIG1_MCS				0x7f
-#define bHTSIG1_BandWidth			0x80
-#define bHTSIG1_HTLength			0xffff
-#define bLSIG_Rate					0xf
-#define bLSIG_Reserved				0x10
-#define bLSIG_Length				0x1fffe
-#define bLSIG_Parity					0x20
-#define bCCKRxPhase				0x4
 #define bLSSIReadAddress			0x3f000000   /* LSSI "Read" Address */
 #define bLSSIReadEdge				0x80000000   /* LSSI "Read" edge signal */
 #define bLSSIReadBackData			0xfff
-#define bLSSIReadOKFlag				0x1000
-#define bCCKSampleRate				0x8	/* 0: 44MHz, 1:88MHz */
-#define bRegulator0Standby			0x1
-#define bRegulatorPLLStandby			0x2
-#define bRegulator1Standby			0x4
-#define bPLLPowerUp				0x8
-#define bDPLLPowerUp				0x10
-#define bDA10PowerUp				0x20
-#define bAD7PowerUp				0x200
-#define bDA6PowerUp				0x2000
-#define bXtalPowerUp				0x4000
-#define b40MDClkPowerUP				0x8000
-#define bDA6DebugMode				0x20000
-#define bDA6Swing					0x380000
-#define bADClkPhase				0x4000000
-#define b80MClkDelay				0x18000000
-#define bAFEWatchDogEnable			0x20000000
 #define bXtalCap					0x0f000000
-#define bIntDifClkEnable			0x400
-#define bExtSigClkEnable			0x800
-#define bBandgapMbiasPowerUp		0x10000
-#define bAD11SHGain				0xc0000
-#define bAD11InputRange				0x700000
-#define bAD11OPCurrent				0x3800000
-#define bIPathLoopback				0x4000000
-#define bQPathLoopback				0x8000000
-#define bAFELoopback				0x10000000
-#define bDA10Swing				0x7e0
-#define bDA10Reverse				0x800
-#define bDAClkSource				0x1000
-#define bAD7InputRange				0x6000
-#define bAD7Gain					0x38000
-#define bAD7OutputCMMode			0x40000
-#define bAD7InputCMMode				0x380000
-#define bAD7Current					0xc00000
-#define bRegulatorAdjust			0x7000000
-#define bAD11PowerUpAtTx			0x1
-#define bDA10PSAtTx				0x10
-#define bAD11PowerUpAtRx			0x100
-#define bDA10PSAtRx				0x1000
-
-#define bCCKRxAGCFormat				0x200
-
-#define bPSDFFTSamplepPoint			0xc000
-#define bPSDAverageNum				0x3000
-#define bIQPathControl				0xc00
-#define bPSDFreq					0x3ff
-#define bPSDAntennaPath				0x30
-#define bPSDIQSwitch				0x40
-#define bPSDRxTrigger				0x400000
-#define bPSDTxTrigger				0x80000000
-#define bPSDSineToneScale			0x7f000000
-#define bPSDReport					0xffff
 
 /* page-9 */
 #define bOFDMTxSC				0x30000000
-- 
2.18.0