Re: [PATCH] mtd: rawnand: denali: add DT property to specify skipped bytes in OOB

[Boris Brezillon]

On Fri, 7 Sep 2018 23:42:53 +0900
Masahiro Yamada <yamada.masahiro@xxxxxxxxxxxxx> wrote:

> Hi Boris,
> 
> 2018-09-07 23:08 GMT+09:00 Boris Brezillon <boris.brezillon@xxxxxxxxxxx>:
> > Hi Masahiro,
> >
> > On Fri,  7 Sep 2018 19:56:23 +0900
> > Masahiro Yamada <yamada.masahiro@xxxxxxxxxxxxx> wrote:
> >  
> >> NAND devices need additional data area (OOB) for error correction,
> >> but it is also used for Bad Block Marker (BBM).  In many cases, the
> >> first byte in OOB is used for BBM, but the location actually depends
> >> on chip vendors.  The NAND controller should preserve the precious
> >> BBM to keep track of bad blocks.
> >>
> >> In Denali IP, the SPARE_AREA_SKIP_BYTES register is used to specify
> >> the number of bytes to skip from the start of OOB.  The ECC engine
> >> will automatically skip the specified number of bytes when it gets
> >> access to OOB area.
> >>
> >> The same value for SPARE_AREA_SKIP_BYTES should be used between
> >> firmware and the operating system if you intend to use the NAND
> >> device across the control hand-off.
> >>
> >> In fact, the current denali.c code expects firmware to have already
> >> set the SPARE_AREA_SKIP_BYTES register, then reads the value out.
> >>
> >> If no firmware (or bootloader) has initialized the controller, the
> >> register value is zero, which is the default after power-on-reset.
> >>
> >> In other words, the Linux driver cannot initialize the controller
> >> by itself.  You cannot support the reset control either because
> >> resetting the controller will get register values lost.
> >>
> >> This commit adds a way to specify it via DT.  If the property
> >> "denali,oob-skip-bytes" exists, the value will be set to the register.  
> >
> > Hm, do we really need to make this config customizable? I mean, either
> > you have a large-page NAND (page > 512 bytes) and the 2 first bytes
> > must be reserved for the BBM or you have a small-page NAND and the BBM
> > is at position 4 and 5. Are you sure people configure that differently?
> > Don't you always have SPARE_AREA_SKIP_BYTES set to 6 or 2?  
> 
> 
> As I said in the patch description,
> I need to use the same SPARE_AREA_SKIP_BYTES value
> across firmware, boot-loader, Linux, and whatever.
> 
> I want to set the value to 8 for my platform
> because the on-chip boot ROM expects 8.
> I cannot change it since the boot ROM is hard-wired.
> 
> 
> The boot ROM skips 8 bytes in OOB
> when it loads images from the on-board NAND device.
> 
> So, when I update the image from U-Boot or Linux,
> I need to make sure to set the register to 8.
> 
> If I update the image with a different value,
> the Boot ROM fails to boot.
> 
> 
> 
> When the system has booted from NAND,
> the register is already set to 8.  It works.
> 
> However, when the system has booted from eMMC,
> the register is not initialized by anyone.
> I am searching for a way to set the register to 8
> in this case.
> 
> 
> The boot ROM in SOCFPGA might expect a different value,
> I am not sure.

Okay, then why not having a per-compatible value if it's related to the
BootROM? Unless the BootROM is part of the FPGA and can be
reprogrammed. I'd really prefer not having a generic property that
allows you to put anything you want.