Re: [PATCH v2 00/34] ARM: dts: tegra: apalis_t30: major revamp incl. v1.1 hardware support

From: Thierry Reding
Date: Wed Sep 26 2018 - 10:47:00 EST


On Fri, Aug 31, 2018 at 06:37:42PM +0200, Marcel Ziswiler wrote:
> This series is a major overhaul and adds support for the V1.1 hardware
> revision of the Toradex Apalis T30 system on module.
>
> Changes in v2:
> - Clean-up PCIe controller/port status' as well.
> - Also move serial UART "nvidia,tegra30-hsuart" compatible to module
> level device trees.
> - Also add two missing newlines.
> - Also replace underscores in node names with dashes.
> - Explicitly disable input of BKL1_ON as well.
> - Replace underscores in node names with dashes.
> - When running some more tests I realized that the reg-addr should
> really be 0x3f. Fix this.
> - Get rid of fake clocks simple bus as suggested by Rob.
> - Replace "[PATCH 27/28] ARM: tegra: apalis_t30: fix pcie switch vendor
> compatible" with "[PATCH v2 26/34] dt-bindings: add broadcom (formerly
> plx technology) vendor prefix" as suggested by Stefan.
> - New patch as suggested by Rob.
> - New patch.
> - Drop "[PATCH 01/28] ARM: tegra: apalis_t30: enable broken-hpi on emmc"
> which should already be handled by the broken-hpi quirk as pointed out
> by Dmitry. If I would find more eMMC parts which exhibit the issue I
> will add them to the quirk as a separate patch.
> - Updated V1.1 device trees with all applicable previous fixes.
>
> Marcel Ziswiler (34):
> ARM: tegra: apalis_t30: fix mmc1 cmd pull-up
> ARM: tegra: apalis_t30: pull-up sd card detect pins
> ARM: tegra: apalis_t30: add local-mac-address property
> ARM: tegra: apalis_t30: reorder pcie properties
> ARM: tegra: apalis_t30: annotate/clean-up pcie controller/port nodes
> ARM: tegra: apalis_t30: reorder host1x/hdmi properties
> ARM: tegra: apalis_t30: regulator clean-up
> ARM: tegra: apalis_t30: add missing regulators
> ARM: tegra: apalis_t30: annotate uarts and move compatible to board
> ARM: tegra: apalis_t30: drop unused cami2c label
> ARM: tegra: apalis_t30: white-space/newline clean-up
> ARM: tegra: apalis_t30: drop unused mmc1/sd1 labels
> ARM: tegra: apalis_t30: annotate mmc1/sd1
> ARM: tegra: apalis_t30: move dr_mode property from phy to controller
> ARM: tegra: apalis_t30: reorder backlight properties
> ARM: tegra: apalis_t30: drop pwmleds
> ARM: tegra: apalis_t30: pinmux clean-up
> ARM: tegra: apalis_t30: add missing pinmux
> ARM: tegra: apalis_t30: use proper irq-gpio for stmpe811
> ARM: tegra: apalis_t30: further lm95245 temperature sensor annotation
> ARM: tegra: apalis_t30: add i2c-thermtrip
> ARM: tegra: apalis_t30: add proper emmc vmmc and vqmmc supplies
> ARM: tegra: apalis_t30: enable emmc ddr52 mode
> ARM: tegra: apalis_t30: get rid of fake clocks simple bus
> ARM: tegra: apalis_t30: line break long compatible property line
> dt-bindings: add broadcom (formerly plx technology) vendor prefix
> ARM: tegra: apalis_t30: drop module level model and compatible
> ARM: tegra: apalis_t30: drop obsolete spidev nodes
> ARM: tegra: apalis_t30: hog group for pcie switch reset gpio
> ARM: tegra: apalis_t30: rename hdmiddc to hdmi_ddc
> ARM: tegra: apalis_t30: rename tps65911@2d, stmpe811@41 and
> tps62362@60
> ARM: tegra: apalis_t30: fix mcp2515 can controller interrupt polarity
> ARM: tegra: apalis_t30: move hda node from carrier to module
> ARM: tegra: apalis_t30: support v1.1 hardware revision
>
> Documentation/devicetree/bindings/arm/tegra.txt | 2 +
> .../devicetree/bindings/vendor-prefixes.txt | 1 +
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/tegra30-apalis-eval.dts | 148 +--
> arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts | 266 +++++
> arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi | 1189 ++++++++++++++++++++
> arch/arm/boot/dts/tegra30-apalis.dtsi | 705 +++++++++---
> 7 files changed, 2064 insertions(+), 248 deletions(-)
> create mode 100644 arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts
> create mode 100644 arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi

Applied, thanks.

Thierry

Attachment: signature.asc
Description: PGP signature