Re: USB-C device hotplug issue

From: Dennis Wassenberg
Date: Wed Nov 07 2018 - 04:12:25 EST



On 05.11.18 16:35, Mathias Nyman wrote:
> On 26.10.2018 17:07, Alan Stern wrote:
>> On Fri, 26 Oct 2018, Dennis Wassenberg wrote:
>>
>>>>> --- a/drivers/usb/core/hub.c
>>>>> +++ b/drivers/usb/core/hub.c
>>>>> @@ -2815,7 +2815,9 @@ static int hub_port_reset(struct usb_hub *hub, int port1,
>>>>> ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ USB_PORT_FEAT_C_BH_PORT_RESET);
>>>>> ÂÂÂÂÂÂÂÂÂÂÂÂÂ usb_clear_port_feature(hub->hdev, port1,
>>>>> ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ USB_PORT_FEAT_C_PORT_LINK_STATE);
>>>>> -ÂÂÂÂÂÂÂÂÂÂÂ usb_clear_port_feature(hub->hdev, port1,
>>>>> +
>>>>> +ÂÂÂÂÂÂÂÂÂÂÂ if (!warm)
>>>>> +ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ usb_clear_port_feature(hub->hdev, port1,
>>>>> ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ USB_PORT_FEAT_C_CONNECTION);
>>>>> Â ÂÂÂÂÂÂÂÂÂÂÂÂÂ /*
>>>>
>>>> The key fact is that connection events can get lost if they happen to
>>>> occur during a port reset.
>>> Yes.
>>>>
>>>> I'm not entirely certain of the logic here, but it looks like the
>>>> correct test to add should be "if (udev != NULL)", not "if (!warm)".
>>>> Perhaps Mathias can confirm this
>
> Sorry about the late response, got distracted while performing git
> archeology.
>
> "if (udev != NULL)" would seem more reasonable.
>
> Logs show that clearing the FEAT_C_CONNECTION was originally added
> after a hot reset failed, and before issuing a warm reset to a SS.Inactive
> link. (see 10d674a USB: When hot reset for USB3 fails, try warm reset.)
>
> Apparently all the change flags needed to be cleared for some specific
> host + device combination before issuing a warm reset for the enumeration
> to work properly.
>
> The change to always clear FEAT_C_CONNECTION for USB3 was done later in patch:
> a24a607 USB: Rip out recursive call on warm port reset.
>
> Motivation was:
>
> "In hub_port_finish_reset, unconditionally clear the connect status
> Âchange (CSC) bit for USB 3.0 hubs when the port reset is done. If we
> Âhad to issue multiple warm resets for a device, that bit may have been
> Âset if the device went into SS.Inactive and then was successfully warm
> Âreset."
>
>>> I don't know if clearing the USB_PORT_FEAT_C_CONNECTION bit is
>>> correct in case of a non warm reset. In my case I always observed a
>>> warm reset because of the link state change.
>>> Thats why I checked the warm variable to not change the behavoir for
>>> cases a didn't checked for the first shot.
>>
>> (The syntax of that last sentence is pretty mangled; I can't understand
>> it.)
>>
>> Think of it this way:
>>
>> ÂÂÂÂIf a device was not attached before the reset, we don't want
>> ÂÂÂÂto clear the connect-change status because then we wouldn't
>> ÂÂÂÂrecognize a device that was plugged in during the reset.
>>
>> ÂÂÂÂIf a device was attached before the reset, we don't want any
>> ÂÂÂÂconnect-change status which might be provoked by the reset to
>> ÂÂÂÂlast, because we don't want the core to think that the device
>> ÂÂÂÂwas unplugged and replugged when all that happened was a reset.
>>
>> So the important criterion is whether or not a device was attached to
>> the port when the reset started. It's something of a coincidence that
>> you only observe warm resets when there's nothing attached.
>>
>>> During the first run of usb_hub_reset the udev is NULL because in
>>> this situation the device is not attached logically.
>>>
>>> [Â 112.889810] usb 4-1-port1: XXX: port_event: portstatus: 0x2c0, portchange: 0x40!
>>> [Â 113.201192] usb 4-1-port1: XXX: hub_port_reset: udev:ÂÂÂÂÂÂÂÂÂÂÂ (nil)!
>>> [Â 113.201198] usb 4-1-port1: XXX: hub_port_reset (not clearing USB_PORT_FEAT_C_CONNECTION): 0x203, portchange: 0x1!
>>> [Â 113.253612] usb 4-1-port1: XXX: port_event: portstatus: 0x203, portchange: 0x1!
>>> [Â 113.377208] usb 4-1-port1: XXX: hub_port_reset: udev: ffff88046b302800!
>>> [Â 113.377214] usb 4-1-port1: XXX: hub_port_reset (not clearing USB_PORT_FEAT_C_CONNECTION): 0x203, portchange: 0x0!
>>> [Â 113.429478] usb 4-1.1: new SuperSpeed USB device number 7 using xhci_hcd
>>> [Â 113.442370] usb 4-1.1: New USB device found, idVendor=0781, idProduct=5596
>>> [Â 113.442376] usb 4-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
>>> [Â 113.442381] usb 4-1.1: Product: Ultra T C
>>> [Â 113.442385] usb 4-1.1: Manufacturer: SanDisk
>>> [Â 113.442388] usb 4-1.1: SerialNumber: 4C530001131013121031
>>>
>>> Or maybe we can skip clearing the USB_PORT_FEAT_C_CONNECTION bit in
>>> case of hub_port_reset completely without any other check?
>>
>> See above.
>
> Checking for udev sounds reasonable to me.
> Not sure if we should worry about the specific host+device combo that needed flags
> cleared before warm reset. See patch:
>
> 10d674a USB: When hot reset for USB3 fails, try warm reset.
> https://marc.info/?l=linux-usb&m=131603549603799&w=2
>
> -Mathias
Checking for udev works well too in my case. So there is no need to check the warm flag.

Regarding the other point about the specific host+device combo which needs the flags cleared, I don't know how to proceed.

Best regards,

Dennis