Re: [PATCH 2/3] ARM: dts: sun8i: add FriendlyARM NanoPi Duo2

[Maxime Ripard]

Hi,

On Tue, Dec 18, 2018 at 09:24:56PM +0000, Karl Palsson wrote:
> This is an Allwinner H3 based board, with 512MB ram, a USB OTG port,
> microsd slot, an onboard AP6212A wifi/bluetooth module, and a CSI
> connector.
> 
> Full details and schematic available from vendor:
> http://wiki.friendlyarm.com/wiki/index.php/NanoPi_Duo2
> 
> Signed-off-by: Karl Palsson <karlp@xxxxxxxxxxxx>
> ---
>  arch/arm/boot/dts/Makefile                 |   1 +
>  arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts | 148 +++++++++++++++++++++++++++++
>  2 files changed, 149 insertions(+)
>  create mode 100644 arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 78551c4375d5..7f296bfea94a 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1063,6 +1063,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
>  	sun8i-h3-beelink-x2.dtb \
>  	sun8i-h3-libretech-all-h3-cc.dtb \
>  	sun8i-h3-mapleboard-mp130.dtb \
> +	sun8i-h3-nanopi-duo2.dtb \
>  	sun8i-h3-nanopi-m1.dtb	\
>  	sun8i-h3-nanopi-m1-plus.dtb \
>  	sun8i-h3-nanopi-neo.dtb \
> diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts
> new file mode 100644
> index 000000000000..07d2f1bebd56
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts
> @@ -0,0 +1,148 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2018 Karl Palsson <karlp@xxxxxxxxxxxx>
> + */
> +
> +/dts-v1/;
> +#include "sun8i-h3.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> +	model = "FriendlyARM NanoPi Duo2";
> +	compatible = "friendlyarm,nanopi-duo2", "allwinner,sun8i-h3";
> +
> +	aliases {
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		status {
> +			label = "nanopi:green:status";
> +			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "heartbeat";
> +		};
> +
> +		pwr {
> +			label = "nanopi:red:pwr";
> +			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +		};
> +	};
> +
> +	r_gpio_keys {
> +		compatible = "gpio-keys";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&sw_r_npi>;
> +
> +		k1 {
> +			label = "k1";
> +			linux,code = <BTN_0>;
> +			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
> +	reg_vdd_cpux: vdd-cpux-regulator {
> +		compatible = "regulator-gpio";
> +		regulator-name = "vdd-cpux";
> +		regulator-boot-on;
> +		regulator-always-on;
> +		regulator-min-microvolt = <1100000>;
> +		regulator-max-microvolt = <1300000>;
> +		regulator-ramp-delay = <50>; /* 4ms */
> +
> +		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
> +		enable-active-high;
> +		gpios-states = <0x1>;
> +		states = <1100000 0x0
> +			  1300000 0x1>;
> +	};
> +
> +	wifi_pwrseq: wifi_pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> +	};
> +
> +};
> +
> +&cpu0 {
> +	cpu-supply = <&reg_vdd_cpux>;
> +};
> +
> +&usb_otg {
> +	status = "okay";
> +	dr_mode = "otg";
> +};
> +
> +&ehci0 {
> +	status = "okay";
> +};
> +
> +&ohci0 {
> +	status = "okay";
> +};
> +
> +&reg_usb0_vbus {
> +	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
> +	status = "okay";
> +};
> +
> +&r_pio {
> +	sw_r_npi: key_pins {
> +		pins = "PL3";
> +		function = "gpio_in";
> +	};
> +};

This node isn't needed you can just remove it

> +&usbphy {
> +	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
> +	usb0_vbus-supply = <&reg_usb0_vbus>;
> +	status = "okay";
> +};
> +
> +&mmc0 {
> +	bus-width = <4>;
> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> +	status = "okay";
> +	vmmc-supply = <&reg_vcc3v3>;
> +};
> +
> +&mmc1 {
> +	vmmc-supply = <&reg_vcc3v3>;
> +	vqmmc-supply = <&reg_vcc3v3>;
> +	mmc-pwrseq = <&wifi_pwrseq>;
> +	bus-width = <4>;
> +	non-removable;
> +	status = "okay";
> +
> +	sdio_wifi: sdio_wifi@1 {
> +		reg = <1>;
> +		compatible = "brcm,bcm4329-fmac";
> +		interrupt-parent = <&pio>;
> +		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
> +		interrupt-names = "host-wake";
> +	};
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_pins_a>;
> +	status = "okay";
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart2_pins>, <&uart2_rts_cts_pins>;
> +	uart-has-rtscts;
> +	status = "okay";
> +
> +	/* bluetooth goes here */

The patches for the bluetooth support using serdev by Chen-Yu just got
in:
http://lists.infradead.org/pipermail/linux-arm-kernel/2018-December/621207.html

Ideally, you should put a dt node for the bluetooth part here.

Thanks!
Maxime

-- 
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com