[PATCH] drm: Require PCI for selecting VGA_ARB.

[Maarten Lankhorst]

Op 08-01-2019 om 16:07 schreef Paul Menzel:
> Dear Linux folks,
>
>
> Building Linux 5.0-rc1 fails with the errors below. Please find the
> configuration file attached.
>
> ```
> $ make -j120
> [â]
> drivers/gpu/vga/vgaarb.c: In function â__vga_trygetâ:
> drivers/gpu/vga/vgaarb.c:286:14: error: âPCI_VGA_STATE_CHANGE_DECODESâ undeclared (first use in this function); did you mean âPCI_SUBTRACTIVE_DECODEâ?
>      flags |= PCI_VGA_STATE_CHANGE_DECODES;
>               ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
>               PCI_SUBTRACTIVE_DECODE
> drivers/gpu/vga/vgaarb.c:286:14: note: each undeclared identifier is reported only once for each function it appears in
>   CC [M]  net/netfilter/xt_realm.o
>   CC      drivers/hid/hid-cherry.o
> drivers/gpu/vga/vga_switcheroo.c: In function âvga_switcheroo_runtime_suspendâ:
> drivers/gpu/vga/vga_switcheroo.c:1053:2: error: implicit declaration of function âpci_bus_set_current_stateâ; did you mean â__set_current_stateâ? [-Werror=implicit-function-declaration]
>   pci_bus_set_current_state(pdev->bus, PCI_D3cold);
>   ^~~~~~~~~~~~~~~~~~~~~~~~~
>   __set_current_state
> drivers/gpu/vga/vgaarb.c:291:13: error: âPCI_VGA_STATE_CHANGE_BRIDGEâ undeclared (first use in this function); did you mean âPCI_VGA_STATE_CHANGE_DECODESâ?
>     flags |= PCI_VGA_STATE_CHANGE_BRIDGE;
>              ^~~~~~~~~~~~~~~~~~~~~~~~~~~
>              PCI_VGA_STATE_CHANGE_DECODES
>   CC      fs/reiserfs/dir.o
>   LD [M]  net/tipc/tipc.o
> drivers/gpu/vga/vga_switcheroo.c: In function âvga_switcheroo_runtime_resumeâ:
> drivers/gpu/vga/vga_switcheroo.c:1067:2: error: implicit declaration of function âpci_wakeup_busâ; did you mean â__wake_up_bitâ? [-Werror=implicit-function-declaration]
>   pci_wakeup_bus(pdev->bus);
>   ^~~~~~~~~~~~~~
>   __wake_up_bit
> drivers/gpu/vga/vgaarb.c:293:3: error: implicit declaration of function âpci_set_vga_stateâ; did you mean âpci_set_power_stateâ? [-Werror=implicit-function-declaration]
>    pci_set_vga_state(conflict->pdev, false, pci_bits, flags);
>    ^~~~~~~~~~~~~~~~~
>    pci_set_power_state
>   CC      fs/read_write.o
>   CC      drivers/hid/hid-chicony.o
>   CC      drivers/hid/hid-cypress.o
> drivers/gpu/vga/vgaarb.c: In function âvga_arb_device_initâ:
> drivers/gpu/vga/vgaarb.c:1495:25: error: âpci_bus_typeâ undeclared (first use in this function); did you mean âpci_pcie_typeâ?
>   bus_register_notifier(&pci_bus_type, &pci_notifier);
>                          ^~~~~~~~~~~~
>                          pci_pcie_type
> cc1: some warnings being treated as errors
> make[3]: *** [scripts/Makefile.build:277: drivers/gpu/vga/vgaarb.o] Error 1
> make[3]: *** Waiting for unfinished jobs....
> [â]
> ```
>
>
> Kind regards,
>
> Paul

WARNING: unmet direct dependencies detected for VGA_ARB
  Depends on [n]: HAS_IOMEM [=y] && PCI [=n] && !S390
  Selected by [y]:
  - VGA_SWITCHEROO [=y] && HAS_IOMEM [=y] && X86 [=y] && ACPI [=y]

So I guess you need to enable PCI, probably not a common config you're using. :)

Especially since you selected EXPERT.

Oh well, apply this with git am --scissors?
-----8<----
When configuring the kernel without PCI we can still enable VGA switcheroo,
which is not possible because VGA_ARB cannot be selected.

Remove this by depending on PCI for !S390.

Reported-by: Paul Menzel <pmenzel@xxxxxxxxxxxxx>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@xxxxxxxxxxxxxxx>
---
diff --git a/drivers/gpu/vga/Kconfig b/drivers/gpu/vga/Kconfig
index b677e5d524e6..ef5671475870 100644
--- a/drivers/gpu/vga/Kconfig
+++ b/drivers/gpu/vga/Kconfig
@@ -21,6 +21,7 @@ config VGA_SWITCHEROO
 	bool "Laptop Hybrid Graphics - GPU switching support"
 	depends on X86
 	depends on ACPI
+	depends on (PCI && !S390) # For VGA_ARB
 	select VGA_ARB
 	help
 	  Many laptops released in 2008/9/10 have two GPUs with a multiplexer