Re: [PATCH 1/2] ARM: dts: meson8b: odroidc1: Enable usb phy node
From: Anand Moon
Date: Sun Jan 20 2019 - 13:44:31 EST
Hi Martin,
Thanks for your review comments.
On Sat, 19 Jan 2019 at 03:59, Martin Blumenstingl
<martin.blumenstingl@xxxxxxxxxxxxxx> wrote:
>
> Hi Anand,
>
> thank you for this patch!
>
> On Sun, Jan 13, 2019 at 7:18 PM Anand Moon <linux.amoon@xxxxxxxxx> wrote:
> >
> > Add missing vbus-supply link to phy controller for usb_phy0
> > and usb_phy1 nodes, this changes fixed the power issue
> > on usb ports usb, changes help fix usb reset warning.
> I trust you on the fact that GPIOAO_5 controls VBUS of USB0 and USB1
>
> to me the schematics are not 100% clear or I'm bad at interpreting them:
> - I'll refer to odroid-c1+_rev0.4_20150615.pdf
> - page 1 lists GPIOAO.BIT5 as input for the PWREN signal of the
> USB_OTG controller (usb0)
> - page 1 also shows a PWREN signal in the USB_HOST controller (usb1)
> but not it's input
> - based on your patch I assume that PWREN is the same signal for both
> USB controllers
>
As per the schematics odroid-c1+_rev0.4_20150615.pdf
It seem that their vbus setting for *OTG* port. *Bus 01.Port 1* using
*GPIOAO.BIT5* gpio
But we also need set power supply for *USB_B* port. *Bus 02.Port 1* ?
I don't know but I will try to find solution.
We need to enable some bit in phy driver ?
> > [ 821.991470] usb 1-1.2: reset high-speed USB device number 3 using dwc2
> > [ 825.243385] usb 1-1.2: reset high-speed USB device number 3 using dwc2
> > [ 828.151310] usb 1-1.2: reset high-speed USB device number 3 using dwc2
> > [ 830.991241] usb 1-1.2: reset high-speed USB device number 3 using dwc2
> >
> > Fixes: 2eb79a4d15ff (ARM: dts: meson: enabling the USB Host controller on Odroid-C1/C1+ board)
> you already split your original patch into two, however I suggest
> splitting these patches differently:
> - this one (personally I would choose "ARM: dts: meson8b: odroidc1:
> fix USB VBUS supplies" as title), which contains the Fixes tag, adds
> the "usb_vbus" and references it in the "usb0" and "usb1" nodes
> - enables usb0_phy and usb0 as part of your second patch (I would call
> that "ARM: dts: meson8b: odroidc1: enable the OTG capable USB
> controller")
Ok I will fix this as per you suggestion in the next version.
>
> > Cc: Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>
> > Cc: Jerome Brunet <jbrunet@xxxxxxxxxxxx>
> > Cc: Neil Armstrong <narmstrong@xxxxxxxxxxxx>
> > Signed-off-by: Anand Moon <linux.amoon@xxxxxxxxx>
> > ---
> > Rebased on Kevin's amlogic/v5.0/fixes branch
> >
> > [alarm@archl-c1t ~]$ lsusb -t
> > /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
> > |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M
> > |__ Port 1: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M
> > |__ Port 3: Dev 3, If 0, Class=Video, Driver=uvcvideo, 480M
> > |__ Port 3: Dev 3, If 1, Class=Video, Driver=uvcvideo, 480M
> > |__ Port 3: Dev 3, If 2, Class=Audio, Driver=snd-usb-audio, 480M
> > |__ Port 3: Dev 3, If 3, Class=Audio, Driver=snd-usb-audio, 480M
> > [alarm@archl-c1t ~]$
> > [alarm@archl-c1t ~]$ lsusb -v|egrep "^Bus|MaxPower"
> > Couldn't open device, some information will be missing
> > Bus 001 Device 003: ID 1b71:0056 Fushicai
> > MaxPower 500mA
> > Couldn't open device, some information will be missing
> > Bus 001 Device 004: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS567 SATA 6Gb/s bridge
> > MaxPower 30mA
> > Couldn't open device, some information will be missing
> > Couldn't open device, some information will be missing
> > Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
> > MaxPower 100mA
> > Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> > MaxPower 0mA
> > ---
> > arch/arm/boot/dts/meson8b-odroidc1.dts | 23 +++++++++++++++++++++++
> > 1 file changed, 23 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
> > index 0f0a46ddf3ff..a49a8509b288 100644
> > --- a/arch/arm/boot/dts/meson8b-odroidc1.dts
> > +++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
> > @@ -83,6 +83,19 @@
> > regulator-max-microvolt = <5000000>;
> > };
> >
> > + usb_vbus: regulator-usb-vbus {
> please add a comment here with some details about the regulator and
> add a hint that the signal in the schematics is called "PWREN"
Ok I will add this comment in the next patch.
>
> > + compatible = "regulator-fixed";
> > +
> > + regulator-name = "USB_VBUS";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > +
> > + vin-supply = <&p5v0>;
> > +
> > + gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > tflash_vdd: regulator-tflash_vdd {
> > /*
> > * signal name from schematics: TFLASH_VDD_EN
> > @@ -293,8 +306,18 @@
> > pinctrl-names = "default";
> > };
> >
> > +&usb0_phy {
> > + status = "okay";
> > + vbus-supply = <&usb_vbus>;
> > +};
> > +
> > &usb1_phy {
> > status = "okay";
> > + vbus-supply = <&usb_vbus>;
> > +};
> > +
> > +&usb0 {
> > + status = "okay";
> > };
> I believe there's a problem with the usb/usb_phy nodes here. on my
> Odroid-C1 this results in:
> # cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS
> USB_VBUS 0 0 0 unknown 5000mV 0mA
> 5000mV 5000mV
> (open count is 0)
>
> if I move "vbus-supply" to the "usb1" node (just as an example) then I get:
> # cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS
> USB_VBUS 1 1 0 unknown 5000mV 0mA
> 5000mV 5000mV
Sorry for the mixing the vbus-supply node.
After fix the phy driver code and dts changes I am getting this changes.
# cat /sys/kernel/debug/regulator/regulator_summary | grep USB_VBUS
USB_VBUS 1 2 0 unknown 5000mV
0mA 5000mV 5000mV
Now I am able to enable both *Bus 01.Port 1* and *Bus 02.Port 1*
# lsusb -t
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M
|__ Port 1: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M
|__ Port 3: Dev 3, If 0, Class=Video, Driver=uvcvideo, 480M
|__ Port 3: Dev 3, If 1, Class=Video, Driver=uvcvideo, 480M
|__ Port 3: Dev 3, If 2, Class=Audio, Driver=snd-usb-audio, 480M
|__ Port 3: Dev 3, If 3, Class=Audio, Driver=snd-usb-audio, 480M
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
But not usb device are getting enable on *Bus 01.Port 1*
>
> unfortunately neither your original patch nor the modified version
> seem to enable USB VBUS on my Odroid-C1.
> I have documented my findings already back in December, see "USB
> issues on Odroid-C1" [0]
> help on that would be highly appreciated :)
>
> on which board revision have you tested this patch?
>
I have with me for testing
ODROID-C0 REV 0.4 20151217
ODROID-C1+ REV 0.4 20150615 ----> current testing on
ODROID-C1+ REV 0.4 20160226
>
> Regards
> Martin
>
>
> [0] http://lists.infradead.org/pipermail/linux-amlogic/2018-December/009451.html
Best Regards
-Anand