Re: [PATCH v8 06/11] mfd: max77650: new core mfd driver

From: Bartosz Golaszewski
Date: Thu Apr 04 2019 - 03:31:06 EST

Next message: Dave Young: "Re: [PATCH v3] x86/boot: Use efi_setup_data for searching RSDP on kexec-ed kernel"
Previous message: Mukesh Ojha: "Re: [PATCH] mm: __pagevec_lru_add_fn: typo fix"
In reply to: Lee Jones: "Re: [PATCH v8 06/11] mfd: max77650: new core mfd driver"
Next in thread: Bartosz Golaszewski: "[PATCH v8 09/11] leds: max77650: add LEDs support"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

czw., 4 kwi 2019 o 09:15 Lee Jones <lee.jones@xxxxxxxxxx> napisaÅ(a):
>
> On Wed, 03 Apr 2019, Bartosz Golaszewski wrote:
>
> > From: Bartosz Golaszewski <bgolaszewski@xxxxxxxxxxxx>
> >
> > Add the core mfd driver for max77650 PMIC. We define five sub-devices
> > for which the drivers will be added in subsequent patches.
> >
> > Signed-off-by: Bartosz Golaszewski <bgolaszewski@xxxxxxxxxxxx>
> > ---
> > drivers/mfd/Kconfig | 14 +++
> > drivers/mfd/Makefile | 1 +
> > drivers/mfd/max77650.c | 234 +++++++++++++++++++++++++++++++++++
> > include/linux/mfd/max77650.h | 59 +++++++++
> > 4 files changed, 308 insertions(+)
> > create mode 100644 drivers/mfd/max77650.c
> > create mode 100644 include/linux/mfd/max77650.h
> >
> > diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> > index 0ce2d8dfc5f1..ade04e124aa0 100644
> > --- a/drivers/mfd/Kconfig
> > +++ b/drivers/mfd/Kconfig
> > @@ -733,6 +733,20 @@ config MFD_MAX77620
> > provides common support for accessing the device; additional drivers
> > must be enabled in order to use the functionality of the device.
> >
> > +config MFD_MAX77650
> > + tristate "Maxim MAX77650/77651 PMIC Support"
> > + depends on I2C
> > + depends on OF || COMPILE_TEST
> > + select MFD_CORE
> > + select REGMAP_I2C
> > + help
> > + Say Y here to add support for Maxim Semiconductor MAX77650 and
> > + MAX77651 Power Management ICs. This is the core multifunction
> > + driver for interacting with the device. The module name is
> > + 'max77650'. Additional drivers can be enabled in order to use
> > + the following functionalities of the device: GPIO, regulator,
> > + charger, LED, onkey.
> > +
> > config MFD_MAX77686
> > tristate "Maxim Semiconductor MAX77686/802 PMIC Support"
> > depends on I2C
> > diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> > index b4569ed7f3f3..5727d099c16f 100644
> > --- a/drivers/mfd/Makefile
> > +++ b/drivers/mfd/Makefile
> > @@ -155,6 +155,7 @@ obj-$(CONFIG_MFD_DA9150) += da9150-core.o
> >
> > obj-$(CONFIG_MFD_MAX14577) += max14577.o
> > obj-$(CONFIG_MFD_MAX77620) += max77620.o
> > +obj-$(CONFIG_MFD_MAX77650) += max77650.o
> > obj-$(CONFIG_MFD_MAX77686) += max77686.o
> > obj-$(CONFIG_MFD_MAX77693) += max77693.o
> > obj-$(CONFIG_MFD_MAX77843) += max77843.o
> > diff --git a/drivers/mfd/max77650.c b/drivers/mfd/max77650.c
> > new file mode 100644
> > index 000000000000..7a6c0a5cf602
> > --- /dev/null
> > +++ b/drivers/mfd/max77650.c
> > @@ -0,0 +1,234 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +//
> > +// Copyright (C) 2018 BayLibre SAS
> > +// Author: Bartosz Golaszewski <bgolaszewski@xxxxxxxxxxxx>
> > +//
> > +// Core MFD driver for MAXIM 77650/77651 charger/power-supply.
> > +// Programming manual: https://pdfserv.maximintegrated.com/en/an/AN6428.pdf
> > +
> > +#include <linux/i2c.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/irq.h>
> > +#include <linux/mfd/core.h>
> > +#include <linux/mfd/max77650.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/regmap.h>
> > +
> > +#define MAX77650_INT_GPI_F_MSK BIT(0)
> > +#define MAX77650_INT_GPI_R_MSK BIT(1)
> > +#define MAX77650_INT_GPI_MSK \
> > + (MAX77650_INT_GPI_F_MSK | MAX77650_INT_GPI_R_MSK)
> > +#define MAX77650_INT_nEN_F_MSK BIT(2)
> > +#define MAX77650_INT_nEN_R_MSK BIT(3)
> > +#define MAX77650_INT_TJAL1_R_MSK BIT(4)
> > +#define MAX77650_INT_TJAL2_R_MSK BIT(5)
> > +#define MAX77650_INT_DOD_R_MSK BIT(6)
> > +
> > +#define MAX77650_INT_THM_MSK BIT(0)
> > +#define MAX77650_INT_CHG_MSK BIT(1)
> > +#define MAX77650_INT_CHGIN_MSK BIT(2)
> > +#define MAX77650_INT_TJ_REG_MSK BIT(3)
> > +#define MAX77650_INT_CHGIN_CTRL_MSK BIT(4)
> > +#define MAX77650_INT_SYS_CTRL_MSK BIT(5)
> > +#define MAX77650_INT_SYS_CNFG_MSK BIT(6)
> > +
> > +#define MAX77650_INT_GLBL_OFFSET 0
> > +#define MAX77650_INT_CHG_OFFSET 1
> > +
> > +#define MAX77650_SBIA_LPM_MASK BIT(5)
> > +#define MAX77650_SBIA_LPM_DISABLED 0x00
> > +
> > +enum {
> > + MAX77650_INT_GPI,
> > + MAX77650_INT_nEN_F,
> > + MAX77650_INT_nEN_R,
> > + MAX77650_INT_TJAL1_R,
> > + MAX77650_INT_TJAL2_R,
> > + MAX77650_INT_DOD_R,
> > + MAX77650_INT_THM,
> > + MAX77650_INT_CHG,
> > + MAX77650_INT_CHGIN,
> > + MAX77650_INT_TJ_REG,
> > + MAX77650_INT_CHGIN_CTRL,
> > + MAX77650_INT_SYS_CTRL,
> > + MAX77650_INT_SYS_CNFG,
> > +};
> > +
> > +static const struct resource max77650_charger_resources[] = {
> > + DEFINE_RES_IRQ_NAMED(MAX77650_INT_CHG, "CHG"),
> > + DEFINE_RES_IRQ_NAMED(MAX77650_INT_CHGIN, "CHGIN"),
> > +};
> > +
> > +static const struct resource max77650_gpio_resources[] = {
> > + DEFINE_RES_IRQ_NAMED(MAX77650_INT_GPI, "GPI"),
> > +};
> > +
> > +static const struct resource max77650_onkey_resources[] = {
> > + DEFINE_RES_IRQ_NAMED(MAX77650_INT_nEN_F, "nEN_F"),
> > + DEFINE_RES_IRQ_NAMED(MAX77650_INT_nEN_R, "nEN_R"),
> > +};
> > +
> > +static const struct mfd_cell max77650_cells[] = {
> > + {
> > + .name = "max77650-regulator",
> > + .of_compatible = "maxim,max77650-regulator",
>
> > + },
> > + {
>
> Nit: Place these all on the same line, like:
>
> }, {
>
> > + .name = "max77650-charger",
> > + .of_compatible = "maxim,max77650-charger",
> > + .resources = max77650_charger_resources,
> > + .num_resources = ARRAY_SIZE(max77650_charger_resources),
> > + },
> > + {
> > + .name = "max77650-gpio",
> > + .of_compatible = "maxim,max77650-gpio",
> > + .resources = max77650_gpio_resources,
> > + .num_resources = ARRAY_SIZE(max77650_gpio_resources),
> > + },
> > + {
> > + .name = "max77650-led",
> > + .of_compatible = "maxim,max77650-led",
> > + },
> > + {
> > + .name = "max77650-onkey",
> > + .of_compatible = "maxim,max77650-onkey",
> > + .resources = max77650_onkey_resources,
> > + .num_resources = ARRAY_SIZE(max77650_onkey_resources),
> > + },
> > +};
> > +
> > +static const struct regmap_irq max77650_irqs[] = {
> > + [MAX77650_INT_GPI] = {
> > + .reg_offset = MAX77650_INT_GLBL_OFFSET,
> > + .mask = MAX77650_INT_GPI_MSK,
> > + .type = {
> > + .type_falling_val = MAX77650_INT_GPI_F_MSK,
> > + .type_rising_val = MAX77650_INT_GPI_R_MSK,
> > + .types_supported = IRQ_TYPE_EDGE_BOTH,
>
> Not really a fan of these silly double/triple tabs everywhere. I like
> a straight line as much as anyone, but I'd probably remove them from
> here.
>
> > + },
> > + },
> > + REGMAP_IRQ_REG(MAX77650_INT_nEN_F,
> > + MAX77650_INT_GLBL_OFFSET, MAX77650_INT_nEN_F_MSK),
> > + REGMAP_IRQ_REG(MAX77650_INT_nEN_R,
> > + MAX77650_INT_GLBL_OFFSET, MAX77650_INT_nEN_R_MSK),
> > + REGMAP_IRQ_REG(MAX77650_INT_TJAL1_R,
> > + MAX77650_INT_GLBL_OFFSET, MAX77650_INT_TJAL1_R_MSK),
> > + REGMAP_IRQ_REG(MAX77650_INT_TJAL2_R,
> > + MAX77650_INT_GLBL_OFFSET, MAX77650_INT_TJAL2_R_MSK),
> > + REGMAP_IRQ_REG(MAX77650_INT_DOD_R,
> > + MAX77650_INT_GLBL_OFFSET, MAX77650_INT_DOD_R_MSK),
> > + REGMAP_IRQ_REG(MAX77650_INT_THM,
> > + MAX77650_INT_CHG_OFFSET, MAX77650_INT_THM_MSK),
> > + REGMAP_IRQ_REG(MAX77650_INT_CHG,
> > + MAX77650_INT_CHG_OFFSET, MAX77650_INT_CHG_MSK),
> > + REGMAP_IRQ_REG(MAX77650_INT_CHGIN,
> > + MAX77650_INT_CHG_OFFSET, MAX77650_INT_CHGIN_MSK),
> > + REGMAP_IRQ_REG(MAX77650_INT_TJ_REG,
> > + MAX77650_INT_CHG_OFFSET, MAX77650_INT_TJ_REG_MSK),
> > + REGMAP_IRQ_REG(MAX77650_INT_CHGIN_CTRL,
> > + MAX77650_INT_CHG_OFFSET, MAX77650_INT_CHGIN_CTRL_MSK),
> > + REGMAP_IRQ_REG(MAX77650_INT_SYS_CTRL,
> > + MAX77650_INT_CHG_OFFSET, MAX77650_INT_SYS_CTRL_MSK),
> > + REGMAP_IRQ_REG(MAX77650_INT_SYS_CNFG,
> > + MAX77650_INT_CHG_OFFSET, MAX77650_INT_SYS_CNFG_MSK),
> > +};
> > +
> > +static const struct regmap_irq_chip max77650_irq_chip = {
> > + .name = "max77650-irq",
> > + .irqs = max77650_irqs,
> > + .num_irqs = ARRAY_SIZE(max77650_irqs),
> > + .num_regs = 2,
> > + .status_base = MAX77650_REG_INT_GLBL,
> > + .mask_base = MAX77650_REG_INTM_GLBL,
> > + .type_in_mask = true,
> > + .type_invert = true,
> > + .init_ack_masked = true,
> > + .clear_on_unmask = true,
> > +};
> > +
> > +static const struct regmap_config max77650_regmap_config = {
> > + .name = "max77650",
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > +};
> > +
> > +static int max77650_i2c_probe(struct i2c_client *i2c)
> > +{
> > + struct regmap_irq_chip_data *irq_data;
> > + struct device *dev = &i2c->dev;
> > + struct irq_domain *domain;
> > + struct regmap *map;
> > + unsigned int val;
> > + int rv;
> > +
> > + map = devm_regmap_init_i2c(i2c, &max77650_regmap_config);
> > + if (IS_ERR(map)) {
> > + dev_err(dev, "unable to initialize i2c regmap\n");
>
> "Unable to initialise I2C Regmap"
>
> > + return PTR_ERR(map);
> > + }
> > +
> > + rv = regmap_read(map, MAX77650_REG_CID, &val);
> > + if (rv) {
> > + dev_err(dev, "unable to read the CID from device\n");
>
> "Unable to read Chip ID"
>
> > + return rv;
> > + }
> > +
> > + switch (MAX77650_CID_BITS(val)) {
> > + case MAX77650_CID_77650A:
> > + case MAX77650_CID_77650C:
> > + case MAX77650_CID_77651A:
> > + case MAX77650_CID_77651B:
> > + break;
> > + default:
>
> So you're exiting silently here. What is the user going to think?
>
> "Chip not supported - ID: %d"
>
> > + return -ENODEV;
> > + }
> > +
> > + /*
> > + * This IC has a low-power mode which reduces the quiescent current
> > + * consumption to ~5.6uA but is only suitable for systems consuming
> > + * less than ~2mA. Since this is not likely the case even on
> > + * linux-based wearables - keep the chip in normal power mode.
> > + */
> > + rv = regmap_update_bits(map,
> > + MAX77650_REG_CNFG_GLBL,
> > + MAX77650_SBIA_LPM_MASK,
> > + MAX77650_SBIA_LPM_DISABLED);
> > + if (rv) {
> > + dev_err(dev, "unable to change the power mode\n");
>
> "Unable ..."
>
> > + return rv;
> > + }
> > +
> > + rv = devm_regmap_add_irq_chip(dev, map, i2c->irq,
> > + IRQF_ONESHOT | IRQF_SHARED, 0,
> > + &max77650_irq_chip, &irq_data);
> > + if (rv) {
> > + dev_err(dev, "unable to add the regmap irq chip\n");
>
> "Unable to add Regmap IRQ chip"
>
> > + return rv;
> > + }
> > +
> > + domain = regmap_irq_get_domain(irq_data);
>
> No error checking?
>

This can only fail is irq_data is NULL and since the previous function
succeeded we know it isn't.

Bart

> > + return devm_mfd_add_devices(dev, PLATFORM_DEVID_NONE,
> > + max77650_cells, ARRAY_SIZE(max77650_cells),
> > + NULL, 0, domain);
> > +}
> > +
> > +static const struct of_device_id max77650_of_match[] = {
> > + { .compatible = "maxim,max77650" },
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(of, max77650_of_match);
> > +
> > +static struct i2c_driver max77650_i2c_driver = {
> > + .driver = {
> > + .name = "max77650",
> > + .of_match_table = of_match_ptr(max77650_of_match),
> > + },
> > + .probe_new = max77650_i2c_probe,
>
> I wrote this years ago. Hasn't it gone away yet?
>
> > +};
> > +module_i2c_driver(max77650_i2c_driver);
> > +
> > +MODULE_DESCRIPTION("MAXIM 77650/77651 multi-function core driver");
> > +MODULE_AUTHOR("Bartosz Golaszewski <bgolaszewski@xxxxxxxxxxxx>");
> > +MODULE_LICENSE("GPL v2");
> > diff --git a/include/linux/mfd/max77650.h b/include/linux/mfd/max77650.h
> > new file mode 100644
> > index 000000000000..c809e211a8cd
> > --- /dev/null
> > +++ b/include/linux/mfd/max77650.h
> > @@ -0,0 +1,59 @@
> > +/* SPDX-License-Identifier: GPL-2.0 */
> > +/*
> > + * Copyright (C) 2018 BayLibre SAS
> > + * Author: Bartosz Golaszewski <bgolaszewski@xxxxxxxxxxxx>
> > + *
> > + * Common definitions for MAXIM 77650/77651 charger/power-supply.
> > + */
> > +
> > +#ifndef MAX77650_H
> > +#define MAX77650_H
> > +
> > +#include <linux/bits.h>
> > +
> > +#define MAX77650_REG_INT_GLBL 0x00
> > +#define MAX77650_REG_INT_CHG 0x01
> > +#define MAX77650_REG_STAT_CHG_A 0x02
> > +#define MAX77650_REG_STAT_CHG_B 0x03
> > +#define MAX77650_REG_ERCFLAG 0x04
> > +#define MAX77650_REG_STAT_GLBL 0x05
> > +#define MAX77650_REG_INTM_GLBL 0x06
> > +#define MAX77650_REG_INTM_CHG 0x07
> > +#define MAX77650_REG_CNFG_GLBL 0x10
> > +#define MAX77650_REG_CID 0x11
> > +#define MAX77650_REG_CNFG_GPIO 0x12
> > +#define MAX77650_REG_CNFG_CHG_A 0x18
> > +#define MAX77650_REG_CNFG_CHG_B 0x19
> > +#define MAX77650_REG_CNFG_CHG_C 0x1a
> > +#define MAX77650_REG_CNFG_CHG_D 0x1b
> > +#define MAX77650_REG_CNFG_CHG_E 0x1c
> > +#define MAX77650_REG_CNFG_CHG_F 0x1d
> > +#define MAX77650_REG_CNFG_CHG_G 0x1e
> > +#define MAX77650_REG_CNFG_CHG_H 0x1f
> > +#define MAX77650_REG_CNFG_CHG_I 0x20
> > +#define MAX77650_REG_CNFG_SBB_TOP 0x28
> > +#define MAX77650_REG_CNFG_SBB0_A 0x29
> > +#define MAX77650_REG_CNFG_SBB0_B 0x2a
> > +#define MAX77650_REG_CNFG_SBB1_A 0x2b
> > +#define MAX77650_REG_CNFG_SBB1_B 0x2c
> > +#define MAX77650_REG_CNFG_SBB2_A 0x2d
> > +#define MAX77650_REG_CNFG_SBB2_B 0x2e
> > +#define MAX77650_REG_CNFG_LDO_A 0x38
> > +#define MAX77650_REG_CNFG_LDO_B 0x39
> > +#define MAX77650_REG_CNFG_LED0_A 0x40
> > +#define MAX77650_REG_CNFG_LED1_A 0x41
> > +#define MAX77650_REG_CNFG_LED2_A 0x42
> > +#define MAX77650_REG_CNFG_LED0_B 0x43
> > +#define MAX77650_REG_CNFG_LED1_B 0x44
> > +#define MAX77650_REG_CNFG_LED2_B 0x45
> > +#define MAX77650_REG_CNFG_LED_TOP 0x46
> > +
> > +#define MAX77650_CID_MASK GENMASK(3, 0)
> > +#define MAX77650_CID_BITS(_reg) (_reg & MAX77650_CID_MASK)
> > +
> > +#define MAX77650_CID_77650A 0x03
> > +#define MAX77650_CID_77650C 0x0a
> > +#define MAX77650_CID_77651A 0x06
> > +#define MAX77650_CID_77651B 0x08
> > +
> > +#endif /* MAX77650_H */
>
> --
> Lee Jones [æçæ]
> Linaro Services Technical Lead
> Linaro.org â Open source software for ARM SoCs
> Follow Linaro: Facebook | Twitter | Blog

Next message: Dave Young: "Re: [PATCH v3] x86/boot: Use efi_setup_data for searching RSDP on kexec-ed kernel"
Previous message: Mukesh Ojha: "Re: [PATCH] mm: __pagevec_lru_add_fn: typo fix"
In reply to: Lee Jones: "Re: [PATCH v8 06/11] mfd: max77650: new core mfd driver"
Next in thread: Bartosz Golaszewski: "[PATCH v8 09/11] leds: max77650: add LEDs support"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]