Re: [PATCH v3 3/6] ARM: dts: sun50i: h6: Introduce Beelink GS1 board

[Maxime Ripard]

On Mon, Apr 08, 2019 at 11:26:16AM +0200, Clément Péron wrote:
> Beelink GS1 is an Allwinner H6 based TV box,
> which support:
> - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
> - GPU Mali-T720
> - 2GB LPDDR3 RAM
> - AXP805 PMIC
> - 1Gbps GMAC via RTL8211E
> - FN-Link 6222B-SRB Wifi/BT
> - 1x USB 2.0 Host and 1x USB 3.0 Host
> - HDMI port
> - S/PDIF Tx
> - IR receiver
> - 5V/2A DC power supply
>
> Signed-off-by: Clément Péron <peron.clem@xxxxxxxxx>
> ---
>  arch/arm64/boot/dts/allwinner/Makefile        |   1 +
>  .../dts/allwinner/sun50i-h6-beelink-gs1.dts   | 262 ++++++++++++++++++
>  2 files changed, 263 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
>
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index e4dce2f6fa3a..2dd806a3d5c9 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-beelink-gs1.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
> new file mode 100644
> index 000000000000..3087e56727e1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
> @@ -0,0 +1,262 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2019 Clément Péron <peron.clem@xxxxxxxxx>
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h6.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> +	model = "Beelink GS1";
> +	compatible = "azw,beelink-gs1", "allwinner,sun50i-h6";
> +
> +	aliases {
> +		ethernet0 = &emac;
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	connector {
> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_con_in: endpoint {
> +				remote-endpoint = <&hdmi_out_con>;
> +			};
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		power {
> +			label = "beelink:white:power";
> +			gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
> +			default-state = "on";
> +		};
> +	};
> +
> +	reg_vcc5v: vcc5v {
> +		/* board wide 5V supply directly from the DC jack */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc-5v";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +	};
> +};
> +
> +&de {
> +	status = "okay";
> +};
> +
> +&ehci0 {
> +	status = "okay";
> +};
> +
> +&emac {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&ext_rgmii_pins>;
> +	phy-mode = "rgmii";
> +	phy-handle = <&ext_rgmii_phy>;
> +	phy-supply = <&reg_aldo2>;
> +	allwinner,rx-delay-ps = <0>;
> +	allwinner,tx-delay-ps = <0>;

These two are at their default values

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

Attachment: signature.asc
Description: PGP signature