Re: [PATCH v2 1/7] s390: vfio-ap: wait for queue empty on queue reset

[Pierre Morel]

On 03/05/2019 23:14, Tony Krowiak wrote:
> Refactors the AP queue reset function to wait until the queue is empty
> after the PQAP(ZAPQ) instruction is executed to zero out the queue as
> required by the AP architecture.
>
> Signed-off-by: Tony Krowiak <akrowiak@xxxxxxxxxxxxx>
> ---
>   drivers/s390/crypto/vfio_ap_ops.c | 35 ++++++++++++++++++++++++++++++++---
>   1 file changed, 32 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/s390/crypto/vfio_ap_ops.c b/drivers/s390/crypto/vfio_ap_ops.c
> index 900b9cf20ca5..b88a2a2ba075 100644
> --- a/drivers/s390/crypto/vfio_ap_ops.c
> +++ b/drivers/s390/crypto/vfio_ap_ops.c
> @@ -271,6 +271,32 @@ static int vfio_ap_mdev_verify_no_sharing(struct ap_matrix_mdev *matrix_mdev)
>   	return 0;
>   }
>   
> +static void vfio_ap_mdev_wait_for_qempty(unsigned long apid, unsigned long apqi)
> +{
> +	struct ap_queue_status status;
> +	ap_qid_t qid = AP_MKQID(apid, apqi);
> +	int retry = 5;
> +
> +	do {
> +		status = ap_tapq(qid, NULL);
> +		switch (status.response_code) {
> +		case AP_RESPONSE_NORMAL:
> +			if (status.queue_empty)
> +				return;
> +			msleep(20);

NIT: 	Fall through ?

> +			break;
> +		case AP_RESPONSE_RESET_IN_PROGRESS:
> +		case AP_RESPONSE_BUSY:
> +			msleep(20);
> +			break;
> +		default:
> +			pr_warn("%s: tapq err %02x: %04lx.%02lx may not be empty\n",
> +				__func__, status.response_code, apid, apqi);

I do not thing the warning sentence is appropriate:
The only possible errors here are if the AP is not available due to AP 
checkstop, deconfigured AP or invalid APQN.


> +			return;
> +		}
> +	} while (--retry);
> +}
> +
>   /**
>    * assign_adapter_store
>    *
> @@ -790,15 +816,18 @@ static int vfio_ap_mdev_group_notifier(struct notifier_block *nb,
>   	return NOTIFY_OK;
>   }
>   
> -static int vfio_ap_mdev_reset_queue(unsigned int apid, unsigned int apqi,
> -				    unsigned int retry)
> +int vfio_ap_mdev_reset_queue(unsigned int apid, unsigned int apqi)
>   {
>   	struct ap_queue_status status;
> +	int retry = 5;
>   
>   	do {
>   		status = ap_zapq(AP_MKQID(apid, apqi));
>   		switch (status.response_code) {
>   		case AP_RESPONSE_NORMAL:
> +			vfio_ap_mdev_wait_for_qempty(apid, apqi);
> +			return 0;
> +		case AP_RESPONSE_DECONFIGURED:

Since you modify the switch, you can return for all the following cases:
AP_RESPONSE_DECONFIGURE
..._CHECKSTOP
..._INVALID_APQN


And you should wait for qempty on AP_RESET_IN_PROGRESS along with 
AP_RESPONSE_NORMAL

>   			return 0;
>   		case AP_RESPONSE_RESET_IN_PROGRESS:
>   		case AP_RESPONSE_BUSY:

While at modifying this function, the AP_RESPONSE_BUSY is not a valid 
code for ZAPQ, you can remove this.

> @@ -824,7 +853,7 @@ static int vfio_ap_mdev_reset_queues(struct mdev_device *mdev)
>   			     matrix_mdev->matrix.apm_max + 1) {
>   		for_each_set_bit_inv(apqi, matrix_mdev->matrix.aqm,
>   				     matrix_mdev->matrix.aqm_max + 1) {
> -			ret = vfio_ap_mdev_reset_queue(apid, apqi, 1);
> +			ret = vfio_ap_mdev_reset_queue(apid, apqi);

IMHO, since you are at changing this call, passing the apqn as parameter 
would be a good simplification.



>   			/*
>   			 * Regardless whether a queue turns out to be busy, or
>   			 * is not operational, we need to continue resetting

Depends on why the reset failed, but this is out of scope.

>


--
Pierre Morel
Linux/KVM/QEMU in BÃblingen - Germany