Re: [RFC 0/2] Add workaround for core wake-up on IPI for i.MX8MQ

[Abel Vesa]

On 19-06-23 13:47:26, Martin Kepplinger wrote:
> On 10.06.19 14:13, Abel Vesa wrote:
> > This is another alternative for the RFC:
> > https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Flkml.org%2Flkml%2F2019%2F3%2F27%2F545&data=02%7C01%7Cabel.vesa%40nxp.com%7C6c9d12c1017745750e3908d6f7d0935a%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C636968872531886931&sdata=DAN3TVPD%2FaQzseYUYAjsnfQM6odM1x8qzsVVslFXAnY%3D&reserved=0
> > 
> > This new workaround proposal is a little bit more hacky but more contained
> > since everything is done within the irq-imx-gpcv2 driver.
> > 
> > Basically, it 'hijacks' the registered gic_raise_softirq __smp_cross_call
> > handler and registers instead a wrapper which calls in the 'hijacked' 
> > handler, after that calling into EL3 which will take care of the actual
> > wake up. This time, instead of expanding the PSCI ABI, we use a new vendor SIP.
> > 
> > I also have the patches ready for TF-A but I'll hold on to them until I see if
> > this has a chance of getting in.
> 
> Let's leave out of the picture for now, how generally applicable and
> mergable your changes are. I'd like to reproduce what you do and test
> cpuidle on imx8mq:
> 
> When applying your changes here and the corresponding ATF changes (
> https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fgithub.com%2Fabelvesa%2Farm-trusted-firmware%2Ftree%2Fimx8mq-err11171&data=02%7C01%7Cabel.vesa%40nxp.com%7C6c9d12c1017745750e3908d6f7d0935a%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C636968872531886931&sdata=nB%2FYGkuRrJYwoBJ1afTjIhoadn9Pn3c2QqRFnShWS0c%3D&reserved=0 if
> I got that right) I don't yet see any difference in the SoC heating up
> under zero load. __cpu_do_idle() is called about every 1ms (without your
> changes, that was even more often but I'm not yet sure if that means
> anything).

You will most probably not see any change in the SoC temp since the cpuidle
only touches the A53s. There are way many more IPs in the SoC that could
heat it up. If you want some real numbers you'll have to measure the power
consumtion on VDD_ARM rail. If you don't want to go through that much trouble
you can use the idlestat tool to measure the times each A53 speends in cpu-sleep
state.

> 
> What I also see is that I get about 10x more "arch_timer" (int.3, GICv3)
> interrupts than without your changes.
> 
> What am I doing wrong? I'd be happy to test, again, regardless of how
> acceptable the workaround is in the end.
> 
> thanks,
> 
>                                   martin