Re: [PATCH v3 3/3] vfio_pci: make use of update_irq_devid and optimize irq ops

[Liu, Jiang]

> On Aug 20, 2019, at 11:24 PM, luoben <luoben@xxxxxxxxxxxxxxxxx> wrote:
> 
> 
> 
> å 2019/8/16 äå12:45, Thomas Gleixner åé:
>> On Thu, 15 Aug 2019, Ben Luo wrote:
>> 
>>>  	if (vdev->ctx[vector].trigger) {
>>> -		free_irq(irq, vdev->ctx[vector].trigger);
>>> -		irq_bypass_unregister_producer(&vdev->ctx[vector].producer);
>>> -		kfree(vdev->ctx[vector].name);
>>> -		eventfd_ctx_put(vdev->ctx[vector].trigger);
>>> -		vdev->ctx[vector].trigger = NULL;
>>> +		if (vdev->ctx[vector].trigger == trigger) {
>>> +			irq_bypass_unregister_producer(&vdev->ctx[vector].producer);
>>> 
>> What's the point of unregistering the producer, just to register it again below?
> Whether producer token changed or not, irq_bypass_register_producer() is a way (seems the
> 
> only way) to update IRTE by VFIO for posted interrupt.
> 
> When posted interrupt is in use, the target IRTE will be used by IOMMU directly to find the
> 
> target CPU for an interrupt posted to VM, since hypervisor is bypassed.
> 
> irq_bypass_register_producer() will modify IRTE based on the information retrieved from KVM,
> 
> 
> 0xffffffff8150a920 : modify_irte+0x0/0x180 [kernel]
> 0xffffffff8150ab94 : intel_ir_set_vcpu_affinity+0xf4/0x150 [kernel]
> 0xffffffff81125f3c : irq_set_vcpu_affinity+0x5c/0xa0 [kernel]
> 0xffffffffa0550818 : vmx_update_pi_irte+0x178/0x290 [kvm_intel]    // get pi_desc etc. from KVM
> 0xffffffffa052b789 : kvm_arch_irq_bypass_add_producer+0x39/0x50 [kvm_intel] (inexact)
> 0xffffffffa024a50b : __connect+0x7b/0xa0 [kvm] (inexact)
> 0xffffffffa024a6a8 : irq_bypass_register_producer+0x108/0x140 [kvm] (inexact)
> 0xffffffffa0338386 : vfio_msi_set_vector_signal+0x1b6/0x2c0 [vfio_pci] (inexact)
>> 
>>> +		} else if (trigger) {
>>> +			ret = update_irq_devid(irq,
>>> +					vdev->ctx[vector].trigger, trigger);
>>> +			if (unlikely(ret)) {
>>> +				dev_info(&pdev->dev,
>>> +					 "update_irq_devid %d (token %p) fails: %d\n",
>>> 
>> s/fails/failed/
>> 
>> 
>>> +					 irq, vdev->ctx[vector].trigger, ret);
>>> +				eventfd_ctx_put(trigger);
>>> +				return ret;
>>> +			}
>>> 
>> This lacks any form of comment why this is correct. dev_id is updated and
>> the producer with the old token is still registered.
>> 
> ok, I will add comment like below:
> 
> For KVM-VFIO case, once producer and consumer connected successfully, interrupt from passthrough
> 
> device will be directly delivered to VM instead of triggering interrupt process in HOST. If producer and
> 
> consumer are disconnected, this interrupt process will fall back to remap mode, the handler vfio_msihandler()
> 
> registered in corresponding irqaction will use the dev_id to find the right way to deliver the interrupt to VM.
> 
> So, it is safe to update dev_id before unregistration of irq-bypass producer, i.e. switch back from posted
> 
> mode to remap mode, since only in remap mode the 'dev_id' will be used by interrupt handler. To producer
> 
> and consumer, dev_id is only a token for pairing them togather.
>> 
>>> +			irq_bypass_unregister_producer(&vdev->ctx[vector].producer);
>>> 
>> Now it's unregistered.
>> 
>> 
>>> +			eventfd_ctx_put(vdev->ctx[vector].trigger);
>>> +			vdev->ctx[vector].producer.token = trigger;
>>> 
>> The token is updated and then it's newly registered below.
>> 
>> 
>>> +			vdev->ctx[vector].trigger = trigger;
>>> -	vdev->ctx[vector].producer.token = trigger;
>>> -	vdev->ctx[vector].producer.irq = irq;
>>> +	/* always update irte for posted mode */
>>>  	ret = irq_bypass_register_producer(&vdev->ctx[vector].producer);
>>>  	if (unlikely(ret))
>>>  		dev_info(&pdev->dev,
>>>  		"irq bypass producer (token %p) registration fails: %d\n",
>>>  		vdev->ctx[vector].producer.token, ret);
>>> 
>> I know this code already existed, but again this looks inconsistent. If the
>> registration fails then a subsequent update will try to unregister a not
>> registered producer. Does not make any sense to me.
>> 
> irq_bypass_register_producer() also fails on duplicated registration, so maybe an unconditional try to
> 
> unregistration is a easy way to keep consistent. 
> 
> Maybe it's better to change these function names to irq_bypass_try_register_producer() and
> 
> irq_bypass_try_unregister_producer()  :)
> 
> 
Hi Ben,
	The point is that we shouldnât blindly try to register again  if we fails to unregister a posted interrupt producer. By this way, the fast path (posted interrupt) may get disabled, but itâs safer than blindly ignoring the failure of ungistration.
Thanks,
Gerry 
> 
> Thanks,
> 
>     Ben