Re: [PATCH] arm64: dts: allwinner: orange-pi-3: Enable WiFi

[OndÅej Jirman]

Hello Maxime,

On Fri, Aug 23, 2019 at 12:08:07PM +0200, Maxime Ripard wrote:
> Hi,
> 
> On Fri, Aug 23, 2019 at 11:42:28AM +0200, megous@xxxxxxxxxx wrote:
> > From: Ondrej Jirman <megous@xxxxxxxxxx>
> >
> > Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is called
> > bcm43356 and can be used with the brcmfmac driver. The module is powered by
> > the two always on regulators (not AXP805).
> >
> > WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be
> > configured so that it sets up an 1.8V input bias on this port. This is done
> > by the pio driver by reading the vcc-pg-supply voltage.
> >
> > You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt
> > configuration that can be found in the Xulongs's repository for H6:
> >
> > https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256
> >
> > Mainline brcmfmac driver expects the firmware and nvram at the following
> > paths relative to the firmware directory:
> >
> >   brcm/brcmfmac43456-sdio.bin
> >   brcm/brcmfmac43456-sdio.txt
> >
> > Signed-off-by: Ondrej Jirman <megous@xxxxxxxxxx>
> > ---
> >
> > Since RTC patches for H6 were merged, this can now go in too, if it looks ok.
> >
> > Other patches for this WiFi chip support were merged in previous cycles,
> > so this just needs enabling in DTS now.
> >
> > Sorry for the links in the commit log, but this information is useful,
> > even if the link itself goes bad. Any pointer what to google for
> > (file names, tree name) is great for anyone searching in the future.
> 
> I understand, but this should (also?) be in the wiki. Please add it
> there too.

Added. Thank you.

  http://linux-sunxi.org/Xunlong_Orange_Pi_3#Firmware_files

regards,
	Ondrej

> > Please take a look.
> >
> > Thank you,
> > 	Ondrej
> >
> >  .../dts/allwinner/sun50i-h6-orangepi-3.dts    | 48 +++++++++++++++++++
> >  1 file changed, 48 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> > index eda9d5f640b9..49d954369087 100644
> > --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> > @@ -56,6 +56,34 @@
> >  		regulator-max-microvolt = <5000000>;
> >  		regulator-always-on;
> >  	};
> > +
> > +	reg_vcc33_wifi: vcc33-wifi {
> > +		/* Always on 3.3V regulator for WiFi and BT */
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "vcc33-wifi";
> > +		regulator-min-microvolt = <3300000>;
> > +		regulator-max-microvolt = <3300000>;
> > +		regulator-always-on;
> > +		vin-supply = <&reg_vcc5v>;
> > +	};
> > +
> > +	reg_vcc_wifi_io: vcc-wifi-io {
> > +		/* Always on 1.8V/300mA regulator for WiFi and BT IO */
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "vcc-wifi-io";
> > +		regulator-min-microvolt = <1800000>;
> > +		regulator-max-microvolt = <1800000>;
> > +		regulator-always-on;
> > +		vin-supply = <&reg_vcc33_wifi>;
> > +	};
> > +
> > +	wifi_pwrseq: wifi_pwrseq {
> > +		compatible = "mmc-pwrseq-simple";
> > +		clocks = <&rtc 1>;
> > +		clock-names = "ext_clock";
> > +		reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
> > +		post-power-on-delay-ms = <200>;
> > +	};
> >  };
> >
> >  &cpu0 {
> > @@ -91,6 +119,25 @@
> >  	status = "okay";
> >  };
> >
> > +&mmc1 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&mmc1_pins>;
> 
> This is the default already. I've removed it and applied.
> 
> Maxime
> 
> --
> Maxime Ripard, Bootlin
> Embedded Linux and Kernel engineering
> https://bootlin.com



> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel