Re: [EXT] Re: [v1,net-next, 1/2] ethtool: add setting frame preemption of traffic classes
From: Murali Karicheri
Date: Mon Dec 30 2019 - 11:51:24 EST
Hi Vinicius,
On 12/18/2019 08:54 PM, Vinicius Costa Gomes wrote:
Hi Ivan,
Ivan Khoronzhuk <ivan.khoronzhuk@xxxxxxxxxx> writes:
Quoting Po Liu (2019-11-27 01:59:18)
IEEE Std 802.1Qbu standard defined the frame preemption of port
traffic classes. This patch introduce a method to set traffic classes
preemption. Add a parameter 'preemption' in struct
ethtool_link_settings. The value will be translated to a binary, each
bit represent a traffic class. Bit "1" means preemptable traffic
class. Bit "0" means express traffic class. MSB represent high number
traffic class.
If hardware support the frame preemption, driver could set the
ethernet device with hw_features and features with NETIF_F_PREEMPTION
when initializing the port driver.
User can check the feature 'tx-preemption' by command 'ethtool -k
devname'. If hareware set preemption feature. The property would be a
fixed value 'on' if hardware support the frame preemption.
Feature would show a fixed value 'off' if hardware don't support the
frame preemption.
Having some knobs in ethtool to enable when/how Frame Preemption is
advertised on the wire makes sense. I also agree that it should be "on"
by default.
Command 'ethtool devname' and 'ethtool -s devname preemption N'
would show/set which traffic classes are frame preemptable.
Port driver would implement the frame preemption in the function
get_link_ksettings() and set_link_ksettings() in the struct ethtool_ops.
In an early RFC series [1], we proposed a way to support frame preemption. I'm
not sure if you have considered it before implementing this other proposal
based on ethtool interface so I thought it would be a good idea to bring that up
to your attention, just in case.
Sorry, I didn't notice the RFC proposal. Using ethtool set the
preemption just thinking about 8021Qbu as standalone. And not limit to
the taprio if user won't set 802.1Qbv.
I see your point of using frame-preemption "standalone", I have two
ideas:
1. add support in taprio to be configured without any schedule in the
"full offload" mode. In practice, allowing taprio to work somewhat
similar to (mqprio + frame-preemption), changes in the code should de
fairly small;
+
And if follow mqprio settings logic then preemption also can be enabled
immediately while configuring taprio first time, and similarly new ADMIN
can't change it and can be set w/o preemption option afterwards.
So that following is correct:
OPER
$ tc qdisc add dev IFACE parent root handle 100 taprio \
base-time 10000000 \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 2@2 \
preemption 0 1 1 1
flags 1
then
ADMIN
$ tc qdisc add dev IFACE parent root handle 100 taprio \
base-time 12000000 \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 2@2 \
preemption 0 1 1 1
sched-entry S 01 300000 \
sched-entry S 02 300000 \
flags 1
then
ADMIN
$ tc qdisc add dev IFACE parent root handle 100 taprio \
base-time 13000000 \
sched-entry S 01 300000 \
sched-entry S 02 300000 \
flags 1
BUT:
1) The question is only should it be in this way? I mean preemption to be
enabled immediately? Also should include other parameters like
fragment size.
We can decide what things are allowed/useful here. For example, it might
make sense to allow "preemption" to be changed. We can extend taprio to
support changing the fragment size, if that makes sense.
The point is it make sense to configure pre-emption related parameters
independently of taprio since they are not related. User may use just
pre-emption to reduce latency in the communication path for their end
application.. So there should be a way to configure it independently of
taprio. Right??
2) What if I want to use frame preemption with another "transmission selection
algorithm"? Say another one "time sensitive" - CBS? How is it going to be
stacked?
I am not seeing any (conceptual*) problems when plugging a cbs (for
example) qdisc into one of taprio children. Or, are you talking about a
more general problem?
If I understand it correctly problem is not stacking taprio with cbs,
but rather pre-emption with other qdiscs and allow configuring
the parameters such as frag size. How do I use frame pre-emption as
an independent feature and configure frag size? Ethool appears to be
better from this point of view as Ivan has mentioned below.
Murali
* here I am considering that support for taprio without an schedule is
added.
In this case ethtool looks better, allowing this "MAC level" feature, to be
configured separately.
My only issue with using ethtool is that then we would have two
different interfaces for "complementary" features. And it would make
things even harder to configure and debug. The fact that one talks about
traffic classes and the other transmission queues doesn't make me more
comfortable as well.
On the other hand, as there isn't a way to implement frame preemption in
software, I agree that it makes it kind of awkward to have it in the tc
subsystem.
At this point, I am slightly in favor of the taprio approach (yes, I am
biased :-), but I can be convinced otherwise. I will be only a little
sad if we choose to go with ethtool for now, and then add support up in
the stack, something similar to "ethtool -N" and "tc-flower".
2. extend mqprio to support frame-preemption;
As some feedback also want to set the MAC merge minimal fragment size
and get some more information of 802.3br.
The minimal fragment size, I guess, also makes sense to be kept in
ethtool. That is we have a sane default, and allow the user to change
this setting for special cases.
In that initial proposal, Frame Preemption feature is configured via taprio qdisc.
For example:
$ tc qdisc add dev IFACE parent root handle 100 taprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 2@2 \
preemption 0 1 1 1 \
base-time 10000000 \
sched-entry S 01 300000 \
sched-entry S 02 300000 \
sched-entry S 04 400000 \
clockid CLOCK_TAI
It also aligns with the gate control operations Set-And-Hold-MAC and Set-And-
Release-MAC that can be set via 'sched-entry' (see Table 8.7 from
802.1Q-2018 for further details.
I am curious about Set-And-Hold-Mac via 'sched-entry'. Actually, it
could be understand as guardband by hardware preemption. MAC should
auto calculate the nano seconds before express entry slot start to
break to two fragments. Set-And-Hold-MAC should minimal larger than
the fragment-size oct times.
Another interesting point. My first idea is that when the schedule is
offloaded to the driver and the driver detects that the "entry" width is
smaller than the fragment side, the driver could reject that schedule
with a nice error message.
Looks ok, if entry command is RELEASE or SET only, but not HOLD, and
only if it contains express queues. And if for entry is expectable to have
interval shorter, the entry has to be marked as HOLD then.
But not every offload is able to support mac/hold per sched (there is
no HOLD/RELEASE commands in this case). For this case seems like here can
be 2 cases:
Yeah, the hw I have in hand also doesn't support the HOLD/RELEASE
commands.
1) there is no âgate closeâ event for the preemptible traffic
2) there is "gate close" event for the preemptable traffic
And both can have the following impact, if assume the main reason to
this guard check is to guarantee the express queue cannot be blocked while
this "close to short" interval opening ofc:
If a preemption fragment is started before "express" frame, then interval
should allow to complete preemption fragment and has to have enough time
to insert express frame. So here situation when maximum packet size per
each queue can have place.
In case of TI am65 this queue MTU is configurable per queue (for similar
reasons and couple more (packet fill feature for instance)) and can be
used for guard check also, but not clear where it should be. Seems like
it should be done using ethtool also, but can be needed for taprio
interface....
For now, at least for the hardware I am working on, something like this
is configurable, but I wasn't planning on exposing it, using the maximum
ethernet frame size seemed a good default.
Please share your thoughts on this.
I am good to see there is frame preemption proposal. Each way is ok
for me but ethtool is more flexible. I've seen the RFC the code. The
hardware offload is in the mainline, but preemption is not yet, I
don't know why. Could you post it again?
It's not mainline because this kind of stuff will not be accepted
upstream without in-tree users. And you are the first one to propose
such a thing :-)
It's just now that I have something that supports frame-preemption, the
code I have is approaching RFC-like quality. I will send another RFC
this week hopefully, and we can see how things look in practice.
Cheers,
--
Vinicius
--
Regards,
Ivan Khoronzhuk
Cheers,
--
Vinicius
--
Murali Karicheri
Texas Instruments