[PATCH 3/4] drm/dp_mst: Increase ACT retry timeout to 3s

From: Lyude Paul
Date: Fri Apr 03 2020 - 16:08:22 EST


Currently we only poll for an ACT up to 30 times, with a busy-wait delay
of 100Âs between each attempt - giving us a timeout of 2900Âs. While
this might seem sensible, it would appear that in certain scenarios it
can take dramatically longer then that for us to receive an ACT. On one
of the EVGA MST hubs that I have available, I observed said hub
sometimes taking longer then a second before signalling the ACT. These
delays mostly seem to occur when previous sideband messages we've sent
are NAKd by the hub, however it wouldn't be particularly surprising if
it's possible to reproduce times like this simply by introducing branch
devices with large LCTs since payload allocations have to take effect on
every downstream device up to the payload's target.

So, instead of just retrying 30 times we poll for the ACT for up to 3ms,
and additionally use usleep_range() to avoid a very long and rude
busy-wait. Note that the previous retry count of 30 appears to have been
arbitrarily chosen, as I can't find any mention of a recommended timeout
or retry count for ACTs in the DisplayPort 2.0 specification. This also
goes for the range we were previously using for udelay(), although I
suspect that was just copied from the recommended delay for link
training on SST devices.

Signed-off-by: Lyude Paul <lyude@xxxxxxxxxx>
Fixes: ad7f8a1f9ced ("drm/helper: add Displayport multi-stream helper (v0.6)")
Cc: Sean Paul <sean@xxxxxxxxxx>
Cc: <stable@xxxxxxxxxxxxxxx> # v3.17+
---
drivers/gpu/drm/drm_dp_mst_topology.c | 26 +++++++++++++++++++-------
1 file changed, 19 insertions(+), 7 deletions(-)

diff --git a/drivers/gpu/drm/drm_dp_mst_topology.c b/drivers/gpu/drm/drm_dp_mst_topology.c
index 7aaf184a2e5f..f313407374ed 100644
--- a/drivers/gpu/drm/drm_dp_mst_topology.c
+++ b/drivers/gpu/drm/drm_dp_mst_topology.c
@@ -4466,17 +4466,30 @@ static int drm_dp_dpcd_write_payload(struct drm_dp_mst_topology_mgr *mgr,
* @mgr: manager to use
*
* Tries waiting for the MST hub to finish updating it's payload table by
- * polling for the ACT handled bit.
+ * polling for the ACT handled bit for up to 3 seconds (yes-some hubs really
+ * take that long).
*
* Returns:
* 0 if the ACT was handled in time, negative error code on failure.
*/
int drm_dp_check_act_status(struct drm_dp_mst_topology_mgr *mgr)
{
- int count = 0, ret;
+ /*
+ * There doesn't seem to be any recommended retry count or timeout in
+ * the MST specification. Since some hubs have been observed to take
+ * over 1 second to update their payload allocations under certain
+ * conditions, we use a rather large timeout value.
+ */
+ const int timeout_ms = 3000;
+ unsigned long timeout = jiffies + msecs_to_jiffies(timeout_ms);
+ int ret;
+ bool retrying = false;
u8 status;

do {
+ if (retrying)
+ usleep_range(100, 1000);
+
ret = drm_dp_dpcd_readb(mgr->aux,
DP_PAYLOAD_TABLE_UPDATE_STATUS,
&status);
@@ -4488,13 +4501,12 @@ int drm_dp_check_act_status(struct drm_dp_mst_topology_mgr *mgr)

if (status & DP_PAYLOAD_ACT_HANDLED)
break;
- count++;
- udelay(100);
- } while (count < 30);
+ retrying = true;
+ } while (jiffies < timeout);

if (!(status & DP_PAYLOAD_ACT_HANDLED)) {
- DRM_DEBUG_KMS("failed to get ACT bit %d after %d retries\n",
- status, count);
+ DRM_DEBUG_KMS("failed to get ACT bit %d after %dms\n",
+ status, timeout_ms);
return -EINVAL;
}
return 0;
--
2.25.1