Re: [PATCH 1/3] dt-bindings: net: bluetooth: Add rtl8723bs-bluetooth

From: Alistair Francis
Date: Sat Apr 04 2020 - 21:28:45 EST


On 4/04/2020 3:42 pm, Martin Blumenstingl wrote:
Hi Alistair,

+Cc Max Chou, he may be interested in this also

[...]
@@ -0,0 +1,56 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/realtek,rtl8723bs-bt.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: RTL8723BS/RTL8723CS Bluetooth Device Tree Bindings
I suggest you also add RTL8822C here (as well as to the compatible enum
and the description below). commit 848fc6164158d6 ("Bluetooth: hci_h5:
btrtl: Add support for RTL8822C") adde support for that chip but didn't
add the dt-binding documentation.


Done!



[...]
+ device-wake-gpios:
+ description:
+ GPIO specifier, used to wakeup the BT module (active high)
+
+ enable-gpios:
+ description:
+ GPIO specifier, used to enable the BT module (active high)
+
+ host-wake-gpios:
+ desciption:
+ GPIO specifier, used to wakeup the host processor (active high)
regarding all GPIOs here: it entirely depends on the board whether these
are active HIGH or LOW. even though the actual Bluetooth part may
require a specific polarity there can be (for example) a transistor on
the board which could be used to invert the polarity (from the SoC's
view).


I have removed the "(active..." part from the GPIOs.



also "make dt_binding_check" reports:
properties:host-wake-gpios: 'maxItems' is a required property
I assume that it'll be the same for the other properties


Added.



+firmware-postfix: firmware postfix to be used for firmware config
there's no other dt-binding that uses "firmware-postfix" yet. However,
there are a few that use "firmware-name". My opinion hasn't changed
since Vasily has posted this series initially: I would not add that
property for now because there seems to be a "standard" config blob
(which works for "all" boards), see Hans' analysis result of the ACPI
config blobs for RTL8723BS: [0].


I have removed the 'firmware-postfix" part from this series.


Getting that "standard" config blob into linux-firmware would be
awesome (I assume licensing is not an issue here, Hans can probably give
more details here). I'm not sure about the licenses of "board specific"
config blobs and whether these can be added to linux-firmware.

also indentation seems wrong here

+reset-gpios: GPIO specifier, used to reset the BT module (active high)
indentation seems wrong here too


Fixed.



also please note that there is currently no support for this property
inside the hci_h5 driver and you don't seem to add support for it within
this series either. so please double check that the reset GPIO is really
wired up on your sopine board.


Removed.



+required:
+ - compatible
+
+examples:
+ - |
+ &uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ status = "okay";
AFAIK the "status" property should be omitted from examples


Removed.


Z
also please add a "uart-has-rtscts" propery, see
Documentation/devicetree/bindings/serial/serial.yaml
Also please update patch #3.


Added.


Thanks for the review.


Alistair




Martin


[0] https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/commit/rtl_bt/rtl8723bs_config-OBDA8723.bin?id=e6b9001e91110c654573b8f8e2db6155d10d3b57