[PATCH v5 2/3] Add the bindings for the bq25150 and bq25155 500mA charging ICs from Texas Instruments.

[Dan Murphy]

From: Ricardo Rivera-Matos <r-rivera-matos@xxxxxx>

Description:
The BQ2515X family of devices are highly integrated battery management
ICs that integrate the most common functions for wearbale devices
namely a charger, an output voltage rail, ADC for battery and system
monitoring, and a push-button controller.

Datasheets:
http://www.ti.com/lit/ds/symlink/bq25150.pdf
http://www.ti.com/lit/ds/symlink/bq25155.pdf

CC: Rob Herring <robh@xxxxxxxxxx>
Signed-off-by: Ricardo Rivera-Matos <r-rivera-matos@xxxxxx>
---
 .../bindings/power/supply/bq2515x.yaml        | 99 +++++++++++++++++++
 1 file changed, 99 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/power/supply/bq2515x.yaml

diff --git a/Documentation/devicetree/bindings/power/supply/bq2515x.yaml b/Documentation/devicetree/bindings/power/supply/bq2515x.yaml
new file mode 100644
index 000000000000..673caf67a993
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/bq2515x.yaml
@@ -0,0 +1,99 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright (C) 2020 Texas Instruments Incorporated
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/power/supply/bq2515x.yaml#";
+$schema: "http://devicetree.org/meta-schemas/core.yaml#";
+
+title: TI bq2515x 500-mA Linear charger family
+
+maintainers:
+  - Dan Murphy <dmurphy@xxxxxx>
+
+description: |
+  The BQ2515x family is a highly integrated battery charge management IC that
+  integrates the most common functions for wearable devices, namely a charger,
+  an output voltage rail, ADC for battery and system monitoring, and
+  push-button controller.
+
+  Specifications about the charger can be found at:
+    http://www.ti.com/lit/ds/symlink/bq25150.pdf
+    http://www.ti.com/lit/ds/symlink/bq25155.pdf
+
+properties:
+  compatible:
+    enum:
+      - ti,bq25150
+      - ti,bq25155
+
+  reg:
+    maxItems: 1
+
+  ac_detect-gpios:
+    description: |
+       GPIO used for connecting the bq2515x device PG (AC Detect)
+       pin.  This pin should be used if possible as this is the
+       recommended way to obtain the charger's input PG state.
+       If this pin is not specified a software-based approach for PG
+       detection is used.
+
+  reset-gpios:
+    description: |
+       GPIO used for hardware reset.
+
+  low-power-gpios:
+    description: |
+       GPIO used for low power mode of IC.
+
+  charge-enable-gpios:
+    description: |
+       GPIO used to turn on and off charging.
+
+  constant-charge-current-max-microamp:
+    description: |
+       Maximum charging current in micro Amps.
+    minimum: 50000
+    maximum: 600000
+
+  precharge-current-max-microamp:
+    description: |
+       Maximum precharging current in micro Amps.
+    minimum: 1250
+    maximum: 77500
+
+  input-current-limit-microamp:
+    description: |
+       Maximum input current in micro Amps.
+    minimum: 50000
+    maximum: 500000
+
+  constant-charge-voltage-max-microvolt:
+    description: |
+       Maximum charging voltage in micro volts.
+    minimum: 3600000
+    maximum: 4600000
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    i2c0 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      charger@6b {
+          compatible = "ti,bq25150";
+          reg = <0x6b>;
+
+          ac_detect-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+          reset-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+          low-power-gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+          charge-enable-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+          constant-charge-current-max-microamp = <300000>;
+          constant-charge-voltage-max-microvolt = <4200000>;
+	  precharge-current-max-microamp = <2500>;
+	  input-current-limit-microamp = <100000>;
+      };
+    };
-- 
2.25.1