Re: [PATCH v7 RESEND 07/13] spi: imx: fix ERR009165

From: Sascha Hauer
Date: Wed May 13 2020 - 03:21:44 EST


On Tue, May 12, 2020 at 01:32:30AM +0800, Robin Gong wrote:
> Change to XCH mode even in dma mode, please refer to the below
> errata:
> https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf

This patch is the one bisecting will end up with when somebody uses an
older SDMA firmware or the ROM scripts. It should have a better
description what happens and what should be done about it.

Sascha

>
> Signed-off-by: Robin Gong <yibin.gong@xxxxxxx>
> Acked-by: Mark Brown <broonie@xxxxxxxxxx>
> ---
> drivers/spi/spi-imx.c | 16 ++++++++--------
> 1 file changed, 8 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
> index f4f28a4..70df8e6 100644
> --- a/drivers/spi/spi-imx.c
> +++ b/drivers/spi/spi-imx.c
> @@ -585,8 +585,8 @@ static int mx51_ecspi_prepare_transfer(struct spi_imx_data *spi_imx,
> ctrl |= mx51_ecspi_clkdiv(spi_imx, t->speed_hz, &clk);
> spi_imx->spi_bus_clk = clk;
>
> - if (spi_imx->usedma)
> - ctrl |= MX51_ECSPI_CTRL_SMC;
> + /* ERR009165: work in XHC mode as PIO */
> + ctrl &= ~MX51_ECSPI_CTRL_SMC;
>
> writel(ctrl, spi_imx->base + MX51_ECSPI_CTRL);
>
> @@ -617,7 +617,7 @@ static void mx51_setup_wml(struct spi_imx_data *spi_imx)
> * and enable DMA request.
> */
> writel(MX51_ECSPI_DMA_RX_WML(spi_imx->wml - 1) |
> - MX51_ECSPI_DMA_TX_WML(spi_imx->wml) |
> + MX51_ECSPI_DMA_TX_WML(0) |
> MX51_ECSPI_DMA_RXT_WML(spi_imx->wml) |
> MX51_ECSPI_DMA_TEDEN | MX51_ECSPI_DMA_RXDEN |
> MX51_ECSPI_DMA_RXTDEN, spi_imx->base + MX51_ECSPI_DMA);
> @@ -1171,7 +1171,11 @@ static int spi_imx_dma_configure(struct spi_master *master)
> tx.direction = DMA_MEM_TO_DEV;
> tx.dst_addr = spi_imx->base_phys + MXC_CSPITXDATA;
> tx.dst_addr_width = buswidth;
> - tx.dst_maxburst = spi_imx->wml;
> + /*
> + * For ERR009165 with tx_wml = 0 could enlarge burst size to fifo size
> + * to speed up fifo filling as possible.
> + */
> + tx.dst_maxburst = spi_imx->devtype_data->fifo_size;
> ret = dmaengine_slave_config(master->dma_tx, &tx);
> if (ret) {
> dev_err(spi_imx->dev, "TX dma configuration failed with %d\n", ret);
> @@ -1265,10 +1269,6 @@ static int spi_imx_sdma_init(struct device *dev, struct spi_imx_data *spi_imx,
> {
> int ret;
>
> - /* use pio mode for i.mx6dl chip TKT238285 */
> - if (of_machine_is_compatible("fsl,imx6dl"))
> - return 0;
> -
> spi_imx->wml = spi_imx->devtype_data->fifo_size / 2;
>
> /* Prepare for TX DMA: */
> --
> 2.7.4
>
>

--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |