[PATCH 5.7 109/120] i2c: cadence: Clear HOLD bit at correct time in Rx path

[Greg Kroah-Hartman]

From: Raviteja Narayanam <raviteja.narayanam@xxxxxxxxxx>

[ Upstream commit 12d4d9ec5eeecd712c73772e422b6d082e66b046 ]

There are few issues on Zynq SOC observed in the stress tests causing
timeout errors. Even though all the data is received, timeout error
is thrown. This is due to an IP bug in which the COMP bit in ISR is
not set at end of transfer and completion interrupt is not generated.

This bug is seen on Zynq platforms when the following condition occurs:
Master read & HOLD bit set & Transfer size register reaches '0'.

One workaround is to clear the HOLD bit before the transfer size
register reaches '0'. The current implementation checks for this at
the start of the loop and also only for less than FIFO DEPTH case
(ignoring the equal to case).

So clear the HOLD bit when the data yet to receive is less than or
equal to the FIFO DEPTH. This avoids the IP bug condition.

Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xxxxxxxxxx>
Acked-by: Michal Simek <michal.simek@xxxxxxxxxx>
Signed-off-by: Wolfram Sang <wsa@xxxxxxxxxx>
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
---
 drivers/i2c/busses/i2c-cadence.c | 19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)

diff --git a/drivers/i2c/busses/i2c-cadence.c b/drivers/i2c/busses/i2c-cadence.c
index 97a0bd6ea31f1..1efdabb5adca0 100644
--- a/drivers/i2c/busses/i2c-cadence.c
+++ b/drivers/i2c/busses/i2c-cadence.c
@@ -230,20 +230,21 @@ static irqreturn_t cdns_i2c_isr(int irq, void *ptr)
 		/* Read data if receive data valid is set */
 		while (cdns_i2c_readreg(CDNS_I2C_SR_OFFSET) &
 		       CDNS_I2C_SR_RXDV) {
-			/*
-			 * Clear hold bit that was set for FIFO control if
-			 * RX data left is less than FIFO depth, unless
-			 * repeated start is selected.
-			 */
-			if ((id->recv_count < CDNS_I2C_FIFO_DEPTH) &&
-			    !id->bus_hold_flag)
-				cdns_i2c_clear_bus_hold(id);
-
 			if (id->recv_count > 0) {
 				*(id->p_recv_buf)++ =
 					cdns_i2c_readreg(CDNS_I2C_DATA_OFFSET);
 				id->recv_count--;
 				id->curr_recv_count--;
+
+				/*
+				 * Clear hold bit that was set for FIFO control
+				 * if RX data left is less than or equal to
+				 * FIFO DEPTH unless repeated start is selected
+				 */
+				if (id->recv_count <= CDNS_I2C_FIFO_DEPTH &&
+				    !id->bus_hold_flag)
+					cdns_i2c_clear_bus_hold(id);
+
 			} else {
 				dev_err(id->adap.dev.parent,
 					"xfer_size reg rollover. xfer aborted!\n");
-- 
2.25.1