Re: [PATCH] clk: imx: Fix reparenting of UARTs not associated with sdout

From: Adam Ford
Date: Mon Dec 07 2020 - 10:52:42 EST


On Sun, Dec 6, 2020 at 11:24 PM Sascha Hauer <s.hauer@xxxxxxxxxxxxxx> wrote:
>
> Hi Adam,
>
> On Fri, Dec 04, 2020 at 12:31:54PM -0600, Adam Ford wrote:
> > The default clock source on i.MX8M Mini and Nano boards use a 24MHz clock,
> > but users who need to re-parent the clock source run into issues because
> > all the UART clocks are enabled whether or not they're needed by sdout.
> >
> > Any attempt to change the parent results in an busy error because the
> > clocks have been enabled already.
> >
> > clk: failed to reparent uart1 to sys_pll1_80m: -16
> >
> > Instead of pre-initializing all UARTS, scan the device tree to see if UART
> > clock is used as stdout before initializing it. Only enable the UART clock
> > if it's needed in order to delay the clock initialization until after the
> > re-parenting of the clocks.
> >
> > Fixes: 9461f7b33d11c ("clk: fix CLK_SET_RATE_GATE with clock rate protection")
> > Suggested-by: Aisheng Dong <aisheng.dong@xxxxxxx>
> > Signed-off-by: Adam Ford <aford173@xxxxxxxxx>
> >
> > diff --git a/drivers/clk/imx/clk.c b/drivers/clk/imx/clk.c
> > index 47882c51cb85..6dcc5fbd8f3f 100644
> > --- a/drivers/clk/imx/clk.c
> > +++ b/drivers/clk/imx/clk.c
> > @@ -163,12 +163,18 @@ __setup_param("earlyprintk", imx_keep_uart_earlyprintk,
> >
> > void imx_register_uart_clocks(struct clk ** const clks[])
> > {
> > + struct clk *uart_clk;
> > if (imx_keep_uart_clocks) {
> > int i;
> >
> > imx_uart_clocks = clks;
> > - for (i = 0; imx_uart_clocks[i]; i++)
> > - clk_prepare_enable(*imx_uart_clocks[i]);
> > + for (i = 0; imx_uart_clocks[i]; i++) {
> > + uart_clk = of_clk_get(of_stdout, i);
>
> This looks wrong. imx_uart_clocks is an array containing all clocks that
> could possibly be used for an UART. With of_clk_get(of_stdout, i) you
> get the nth clock for one specific UART.
> What you have to do here is: For each of imx_uart_clocks[] you have to
> iterate over all clocks of the of_stdout node.

Sascha,

Thanks for the review.

I agree that I'm using the wrong index when checking of_stdout, but I
am not sure we need to loop through imx_uart_clocks at all.
I looked at the NXP repo, and they just focus on looping through
of_stdout and don't reference the imx_uart_clocks. Can't we just loop
through the of_stdout and enable any clocks found in that?

adam


>
> Sascha
>
> > + if (IS_ERR(uart_clk))
> > + continue;
> > + clk_prepare_enable(uart_clk);
> > + clk_put(uart_clk);
> > + }
> > }
> > }
> >
> > --
> > 2.25.1
> >
> >
>
> --
> Pengutronix e.K. | |
> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |