Re: [PATCH] staging: rtl8723bs: align comments

[Eric Curtin]

Hi Fabio,

> I am sorry, I fear I don't understand, checkpatch.sh script says the patch is ok.
> Where have I to add a ' ' (a blank?)?
>
> thank you,
>
> fabio
>

I'm only responding to this because this email is doing a very good job
of avoiding my filters somehow :) I think what Greg means is:

Change this:

 /*
-op_mode
-Set to 0 (HT pure) under the following conditions
-       - all STAs in the BSS are 20/40 MHz HT in 20/40 MHz BSS or
-       - all STAs in the BSS are 20 MHz HT in 20 MHz BSS
-Set to 1 (HT non-member protection) if there may be non-HT STAs
-       in both the primary and the secondary channel
-Set to 2 if only HT STAs are associated in BSS,
-       however and at least one 20 MHz HT STA is associated
-Set to 3 (HT mixed mode) when one or more non-HT STAs are associated
-       (currently non-GF HT station is considered as non-HT STA also)
-*/
+ *op_mode
+ *Set to 0 (HT pure) under the following conditions
+ *      - all STAs in the BSS are 20/40 MHz HT in 20/40 MHz BSS or
+ *      - all STAs in the BSS are 20 MHz HT in 20 MHz BSS
+ *Set to 1 (HT non-member protection) if there may be non-HT STAs
+ *      in both the primary and the secondary channel
+ *Set to 2 if only HT STAs are associated in BSS,
+ *      however and at least one 20 MHz HT STA is associated
+ *Set to 3 (HT mixed mode) when one or more non-HT STAs are associated
+ *      (currently non-GF HT station is considered as non-HT STA also)
+ */

to this:

 /*
-op_mode
-Set to 0 (HT pure) under the following conditions
-       - all STAs in the BSS are 20/40 MHz HT in 20/40 MHz BSS or
-       - all STAs in the BSS are 20 MHz HT in 20 MHz BSS
-Set to 1 (HT non-member protection) if there may be non-HT STAs
-       in both the primary and the secondary channel
-Set to 2 if only HT STAs are associated in BSS,
-       however and at least one 20 MHz HT STA is associated
-Set to 3 (HT mixed mode) when one or more non-HT STAs are associated
-       (currently non-GF HT station is considered as non-HT STA also)
-*/
+ * op_mode
+ * Set to 0 (HT pure) under the following conditions
+ *      - all STAs in the BSS are 20/40 MHz HT in 20/40 MHz BSS or
+ *      - all STAs in the BSS are 20 MHz HT in 20 MHz BSS
+ * Set to 1 (HT non-member protection) if there may be non-HT STAs
+ *      in both the primary and the secondary channel
+ * Set to 2 if only HT STAs are associated in BSS,
+ *      however and at least one 20 MHz HT STA is associated
+ * Set to 3 (HT mixed mode) when one or more non-HT STAs are associated
+ *      (currently non-GF HT station is considered as non-HT STA also)
+ * /

Like Dan said, you need a space after the '*'/

Is mise le meas/Regards,

Eric Curtin

Check out this charity that's close to my heart:

https://www.idonate.ie/fundraiser/11394438_peak-for-pat.html
https://www.facebook.com/Peak-for-Pat-104470678280309
https://www.instagram.com/peakforpat/