Re: [PATCH v31 2/4] scsi: ufs: L2P map management for HPB read

[Can Guo]

On 2021-03-23 14:19, Daejun Park wrote:
> > On 2021-03-23 13:37, Daejun Park wrote:
> > > > On 2021-03-23 12:22, Can Guo wrote:
> > > > > On 2021-03-22 17:11, Bean Huo wrote:
> > > > > > On Mon, 2021-03-22 at 15:54 +0900, Daejun Park wrote:
> > > > > > > +       switch (rsp_field->hpb_op) {
> > > > > > >
> > > > > > > +       case HPB_RSP_REQ_REGION_UPDATE:
> > > > > > >
> > > > > > > +               if (data_seg_len != DEV_DATA_SEG_LEN)
> > > > > > >
> > > > > > > +                       dev_warn(&hpb->sdev_ufs_lu->sdev_dev,
> > > > > > >
> > > > > > > +                                "%s: data seg length is not
> > > > > > > same.\n",
> > > > > > >
> > > > > > > +                                __func__);
> > > > > > >
> > > > > > > +               ufshpb_rsp_req_region_update(hpb, rsp_field);
> > > > > > >
> > > > > > > +               break;
> > > > > > >
> > > > > > > +       case HPB_RSP_DEV_RESET:
> > > > > > >
> > > > > > > +               dev_warn(&hpb->sdev_ufs_lu->sdev_dev,
> > > > > > >
> > > > > > > +                        "UFS device lost HPB information during
> > > > > > > PM.\n");
> > > > > > >
> > > > > > > +               break;
> > > > > >
> > > > > > Hi Deajun,
> > > > > > This series looks good to me. Just here I have one question. You
> > > > > > didn't
> > > > > > handle HPB_RSP_DEV_RESET, just a warning.  Based on your SS UFS, 
> > > > > > how
> > > > > > to
> > > > > > handle HPB_RSP_DEV_RESET from the host side? Do you think we shoud
> > > > > > reset host side HPB entry as well or what else?
> > > > > >
> > > > > >
> > > > > > Bean
> > > > >
> > > > > Same question here - I am still collecting feedbacks from flash
> > > > > vendors
> > > > > about
> > > > > what is recommanded host behavior on reception of HPB Op code 0x2,
> > > > > since it
> > > > > is not cleared defined in HPB2.0 specs.
> > > > >
> > > > > Can Guo.
> > > >
> > > > I think the question should be asked in the HPB2.0 patch, since in
> > > > HPB1.0 device
> > > > control mode, a HPB reset in device side does not impact anything in
> > > > host side -
> > > > host is not writing back any HPB entries to device anyways and HPB
> > > > Read
> > > > cmd with
> > > > invalid HPB entries shall be treated as normal Read(10) cmd without
> > > > any
> > > > problems.
> > >
> > > Yes, UFS device will process read command even the HPB entries are
> > > valid or
> > > not. So it is warning about read performance drop by dev reset.
> >
> > Yeah, but still I am 100% sure about what should host do in case of
> > HPB2.0
> > when it receives HPB Op code 0x2, I am waiting for feedbacks.
>
> I think the host has two choices when it receives 0x2.
> One is nothing on host.
> The other is discarding all HPB entries in the host.
>
> In the JEDEC HPB spec, it as follows:
> When the device is powered off by the host, the device may restore L2P 
> map
> data upon power up or build from the host’s HPB READ command.
>
> If some UFS builds L2P map data from the host's HPB READ commands, we 
> don't
> have to discard HPB entries in the host.
>
> So I thinks there is nothing to do when it receives 0x2.

But in HPB2.0, if we do nothing to active regions in host side, host can 
write
HPB entries (which host thinks valid, but actually invalid in device 
side since
reset happened) back to device through HPB Write Buffer cmds (BUFFER ID 
= 0x2).
My question is that are all UFSs OK with this?

Thanks,
Can Guo.

> Thanks,
> Daejun
>
> > Thanks,
> > Can Guo.
> >
> > > Thanks,
> > > Daejun
> > >
> > > > Please correct me if I am wrong.
> > >
> > >
> > >
> > > > Thanks,
> > > > Can Guo.