Re: [PATCH 2/3] fpga: dfl: Add DFL bus driver for Altera SPI Master

From: Moritz Fischer
Date: Tue Apr 06 2021 - 12:46:49 EST

Next message: Mark Brown: "Re: [PATCH v4 2/6] dt-bindings: PCI: Add bindings for Brcmstb endpoint device voltage regulators"
Previous message: Clemens Gruber: "[PATCH v7 8/8] pwm: pca9685: Add error messages for failed regmap calls"
In reply to: matthew . gerlach: "Re: [PATCH 2/3] fpga: dfl: Add DFL bus driver for Altera SPI Master"
Next in thread: matthew . gerlach: "[PATCH 3/3] hwmon: intel-m10-bmc-hwmon: add sensor support of Intel D5005 card"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hi Matthew,

On Tue, Apr 06, 2021 at 09:05:35AM -0700, matthew.gerlach@xxxxxxxxxxxxxxx wrote:
>
> Hi Moritz,
>
> On Mon, 5 Apr 2021, Moritz Fischer wrote:
>
> > Hi Matthew,
> >
> > On Mon, Apr 05, 2021 at 04:53:00PM -0700, matthew.gerlach@xxxxxxxxxxxxxxx wrote:
> > > From: Matthew Gerlach <matthew.gerlach@xxxxxxxxxxxxxxx>
> > >
> > > This patch adds DFL bus driver for the Altera SPI Master
> > > controller. The SPI master is connected to an Intel SPI Slave to
> > > Avalon Master Bridge, inside an Intel MAX10 BMC Chip.
> > >
> > > Signed-off-by: Matthew Gerlach <matthew.gerlach@xxxxxxxxxxxxxxx>
> > > ---
> > > drivers/fpga/Kconfig | 9 ++
> > > drivers/fpga/Makefile | 1 +
> > > drivers/fpga/dfl-spi-altera.c | 221 ++++++++++++++++++++++++++++++++++++++++++
> > > 3 files changed, 231 insertions(+)
> > > create mode 100644 drivers/fpga/dfl-spi-altera.c
> > >
> > > diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
> > > index d591dd9..0a86994 100644
> > > --- a/drivers/fpga/Kconfig
> > > +++ b/drivers/fpga/Kconfig
> > > @@ -210,6 +210,15 @@ config FPGA_DFL_NIOS_INTEL_PAC_N3000
> > > the card. It also instantiates the SPI master (spi-altera) for
> > > the card's BMC (Board Management Controller).
> > >
> > > +config FPGA_DFL_SPI_ALTERA
> > > + tristate "FPGA DFL Altera SPI Master Driver"
> > > + depends on FPGA_DFL
> > > + select REGMAP
> > > + help
> > > + This is a DFL bus driver for the Altera SPI master controller.
> > > + The SPI master is connected to a SPI slave to Avalon Master
> > > + bridge in a Intel MAX BMC.
> > > +
> > > config FPGA_DFL_PCI
> > > tristate "FPGA DFL PCIe Device Driver"
> > > depends on PCI && FPGA_DFL
> > > diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
> > > index 18dc9885..58a42ad 100644
> > > --- a/drivers/fpga/Makefile
> > > +++ b/drivers/fpga/Makefile
> > > @@ -45,6 +45,7 @@ dfl-afu-objs := dfl-afu-main.o dfl-afu-region.o dfl-afu-dma-region.o
> > > dfl-afu-objs += dfl-afu-error.o
> > >
> > > obj-$(CONFIG_FPGA_DFL_NIOS_INTEL_PAC_N3000) += dfl-n3000-nios.o
> > > +obj-$(CONFIG_FPGA_DFL_SPI_ALTERA) += dfl-spi-altera.o
> > >
> > > # Drivers for FPGAs which implement DFL
> > > obj-$(CONFIG_FPGA_DFL_PCI) += dfl-pci.o
> > > diff --git a/drivers/fpga/dfl-spi-altera.c b/drivers/fpga/dfl-spi-altera.c
> > > new file mode 100644
> > > index 0000000..9bec25fd
> > > --- /dev/null
> > > +++ b/drivers/fpga/dfl-spi-altera.c
> > > @@ -0,0 +1,221 @@
> > > +// SPDX-License-Identifier: GPL-2.0
> > > +/*
> > > + * DFL bus driver for Altera SPI Master
> > > + *
> > > + * Copyright (C) 2020 Intel Corporation, Inc.
> > > + *
> > > + * Authors:
> > > + * Matthew Gerlach <matthew.gerlach@xxxxxxxxxxxxxxx>
> > > + */
> > > +
> > > +#include <linux/types.h>
> > > +#include <linux/kernel.h>
> > > +#include <linux/module.h>
> > > +#include <linux/stddef.h>
> > > +#include <linux/errno.h>
> > > +#include <linux/platform_device.h>
> > > +#include <linux/io.h>
> > > +#include <linux/bitfield.h>
> > > +#include <linux/io-64-nonatomic-lo-hi.h>
> > > +#include <linux/regmap.h>
> > > +#include <linux/spi/spi.h>
> > > +#include <linux/spi/altera.h>
> > > +#include <linux/dfl.h>
> > > +
> > > +struct dfl_altera_spi {
> > > + void __iomem *base;
> > > + struct regmap *regmap;
> > > + struct device *dev;
> > > + struct platform_device *altr_spi;
> > > +};
> > > +
> > > +#define SPI_CORE_PARAMETER 0x8
> > > +#define SHIFT_MODE BIT_ULL(1)
> > > +#define SHIFT_MODE_MSB 0
> > > +#define SHIFT_MODE_LSB 1
> > > +#define DATA_WIDTH GENMASK_ULL(7, 2)
> > > +#define NUM_CHIPSELECT GENMASK_ULL(13, 8)
> > > +#define CLK_POLARITY BIT_ULL(14)
> > > +#define CLK_PHASE BIT_ULL(15)
> > > +#define PERIPHERAL_ID GENMASK_ULL(47, 32)
> > > +#define SPI_CLK GENMASK_ULL(31, 22)
> > > +#define SPI_INDIRECT_ACC_OFST 0x10
> > > +
> > > +#define INDIRECT_ADDR (SPI_INDIRECT_ACC_OFST+0x0)
> > > +#define INDIRECT_WR BIT_ULL(8)
> > > +#define INDIRECT_RD BIT_ULL(9)
> > > +#define INDIRECT_RD_DATA (SPI_INDIRECT_ACC_OFST+0x8)
> > > +#define INDIRECT_DATA_MASK GENMASK_ULL(31, 0)
> > > +#define INDIRECT_DEBUG BIT_ULL(32)
> > > +#define INDIRECT_WR_DATA (SPI_INDIRECT_ACC_OFST+0x10)
> > > +#define INDIRECT_TIMEOUT 10000
> > > +
> > > +static int indirect_bus_reg_read(void *context, unsigned int reg,
> > > + unsigned int *val)
> > > +{
> > > + struct dfl_altera_spi *aspi = context;
> > > + void __iomem *base = aspi->base;
> > > + int loops;
> > > + u64 v;
> > > +
> > > + writeq((reg >> 2) | INDIRECT_RD, base + INDIRECT_ADDR);
> > > +
> > > + loops = 0;
> > > + while ((readq(base + INDIRECT_ADDR) & INDIRECT_RD) &&
> > > + (loops++ < INDIRECT_TIMEOUT))
> > > + cpu_relax();
> > > +
> > > + if (loops >= INDIRECT_TIMEOUT) {
> > > + pr_err("%s timed out %d\n", __func__, loops);
> > > + return -ETIME;
> > > + }
> > > +
> > > + v = readq(base + INDIRECT_RD_DATA);
> > > +
> > > + *val = v & INDIRECT_DATA_MASK;
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int indirect_bus_reg_write(void *context, unsigned int reg,
> > > + unsigned int val)
> > > +{
> > > + struct dfl_altera_spi *aspi = context;
> > > + void __iomem *base = aspi->base;
> > > + int loops;
> > > +
> > > + writeq(val, base + INDIRECT_WR_DATA);
> > > + writeq((reg >> 2) | INDIRECT_WR, base + INDIRECT_ADDR);
> > > +
> > > + loops = 0;
> > > + while ((readq(base + INDIRECT_ADDR) & INDIRECT_WR) &&
> > > + (loops++ < INDIRECT_TIMEOUT))
> > > + cpu_relax();
> > > +
> > > + if (loops >= INDIRECT_TIMEOUT) {
> > > + pr_err("%s timed out %d\n", __func__, loops);
> > > + return -ETIME;
> > > + }
> > > + return 0;
> > > +}
> > > +
> > > +static const struct regmap_config indirect_regbus_cfg = {
> > > + .reg_bits = 32,
> > > + .reg_stride = 4,
> > > + .val_bits = 32,
> > > + .fast_io = true,
> > > +
> > > + .reg_write = indirect_bus_reg_write,
> > > + .reg_read = indirect_bus_reg_read,
> > > +};
> > > +
> > > +static struct spi_board_info m10_bmc_info = {
> > > + .modalias = "m10-d5005",
> > > + .max_speed_hz = 12500000,
> > > + .bus_num = 0,
> > > + .chip_select = 0,
> > > +};
> > > +
> > > +static struct platform_device *create_cntrl(struct device *dev,
> > > + void __iomem *base,
> > > + struct spi_board_info *m10_info)
> > > +{
> > > + struct altera_spi_platform_data pdata;
> > > + struct platform_device_info pdevinfo;
> > > + u64 v;
> > > +
> > > + v = readq(base + SPI_CORE_PARAMETER);
> > > +
> > > + memset(&pdata, 0, sizeof(pdata));
> > > + pdata.mode_bits = SPI_CS_HIGH;
> > > + if (FIELD_GET(CLK_POLARITY, v))
> > > + pdata.mode_bits |= SPI_CPOL;
> > > + if (FIELD_GET(CLK_PHASE, v))
> > > + pdata.mode_bits |= SPI_CPHA;
> > > +
> > > + pdata.num_chipselect = FIELD_GET(NUM_CHIPSELECT, v);
> > > + pdata.bits_per_word_mask =
> > > + SPI_BPW_RANGE_MASK(1, FIELD_GET(DATA_WIDTH, v));
> > > +
> > > + pdata.num_devices = 1;
> > > + pdata.devices = m10_info;
> > > +
> > > + dev_dbg(dev, "%s cs %u bpm 0x%x mode 0x%x\n", __func__,
> > > + pdata.num_chipselect, pdata.bits_per_word_mask,
> > > + pdata.mode_bits);
> > > +
> > > + memset(&pdevinfo, 0, sizeof(pdevinfo));
> > > +
> > > + pdevinfo.name = "subdev_spi_altera";
> > > + pdevinfo.id = PLATFORM_DEVID_AUTO;
> > > + pdevinfo.parent = dev;
> > > + pdevinfo.data = &pdata;
> > > + pdevinfo.size_data = sizeof(pdata);
> > > +
> > > + return platform_device_register_full(&pdevinfo);
> >
> > Should this be a SPI driver? I think looking at the UIO case we had
> > decided against this pattern?
>
> This driver is similar in function to drivers/fpga/dfl-n3000-nios.c which
> uses this design pattern. Is it okay to keep this design pattern for
> consistency?
>
>
> >
> > > +}
> > > +static int dfl_spi_altera_probe(struct dfl_device *dfl_dev)
> > > +{
> > > + struct device *dev = &dfl_dev->dev;
> > > + struct dfl_altera_spi *aspi;
> > > +
> > > + aspi = devm_kzalloc(dev, sizeof(*aspi), GFP_KERNEL);
> > > +
> > > + if (!aspi)
> > > + return -ENOMEM;
> > > +
> > > + dev_set_drvdata(dev, aspi);
> > > +
> > > + aspi->dev = dev;
> > > +
> > > + aspi->base = devm_ioremap_resource(dev, &dfl_dev->mmio_res);
> > > +
> > > + if (IS_ERR(aspi->base)) {
> > > + dev_err(dev, "%s get mem resource fail!\n", __func__);
> > > + return PTR_ERR(aspi->base);
> > > + }
> > > +
> > > + aspi->regmap = devm_regmap_init(dev, NULL, aspi, &indirect_regbus_cfg);
> > > + if (IS_ERR(aspi->regmap))
> > > + return PTR_ERR(aspi->regmap);
> > > +
> > > + aspi->altr_spi = create_cntrl(dev, aspi->base, &m10_bmc_info);
> > > +
> > > + if (IS_ERR(aspi->altr_spi)) {
> > > + dev_err(dev, "%s failed to create spi platform driver\n",
> > > + __func__);
> > > + return PTR_ERR(aspi->base);
> > > + }
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static void dfl_spi_altera_remove(struct dfl_device *dfl_dev)
> > > +{
> > > + struct dfl_altera_spi *aspi = dev_get_drvdata(&dfl_dev->dev);
> > > +
> > > + platform_device_unregister(aspi->altr_spi);
> > > +}
> > > +
> > > +#define FME_FEATURE_ID_MAX10_SPI 0xe
> > > +
> > > +static const struct dfl_device_id dfl_spi_altera_ids[] = {
> > > + { FME_ID, FME_FEATURE_ID_MAX10_SPI },
> > > + { }
> > > +};
> >
> > Maybe you can extend the Altera SPI driver with this part?
>
> The file, drivers/spi/spi-altera.c, already has platform MODULE_ related
> code. Wouldn't moving this code to that file produce conflicts?

I've seen other drivers support multiple busses, so it should be
possible, there might be nuances I'm missing in my brief look at this,
though.

I think one of them would be MODULE_DEVICE_TABLE(platform, ...)
and the other one MODULE_DEVICE_TABLE(dfl, ...)

See drivers/i2c/busses/i2c-designware-platdrv.c for an example (though
they might be guarding against what you describe with CONFIG_OF vs
CONFIG_ACPI)

If that doesn't work we could split it up into

altera-spi-plat.c and altera-spi-dfl.c and altera-spi-core.c
or something of that sort?

My point being, now that we have a bus, let's use it and develop drivers
according to the Linux device model where possible :)

Cheers,
Moritz

Next message: Mark Brown: "Re: [PATCH v4 2/6] dt-bindings: PCI: Add bindings for Brcmstb endpoint device voltage regulators"
Previous message: Clemens Gruber: "[PATCH v7 8/8] pwm: pca9685: Add error messages for failed regmap calls"
In reply to: matthew . gerlach: "Re: [PATCH 2/3] fpga: dfl: Add DFL bus driver for Altera SPI Master"
Next in thread: matthew . gerlach: "[PATCH 3/3] hwmon: intel-m10-bmc-hwmon: add sensor support of Intel D5005 card"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]