Re: [PATCH v2 1/2] Revert "USB: serial: ch341: add new Product ID for CH341A"

[Frank Zago]

On 5/12/21 4:55 AM, Johan Hovold wrote:
> On Tue, May 11, 2021 at 08:07:31PM -0500, Frank Zago wrote:
>> Hello,
>> 
>> On 5/10/21 2:40 AM, Johan Hovold wrote:
>>> On Thu, Apr 22, 2021 at 07:28:51PM -0500, Frank Zago wrote:
>>>> From: frank zago <frank@xxxxxxxx>
>>>> 
>>>> The 0x5512 USB PID is for the I2C/GPIO/SPI interfaces. UART is
>>>>  still present but only the TX and RX pins are available; DTS,
>>>> DTR, ... are used for other things. Remove the PID, and let a
>>>> I2C driver bind to it.
>>>> 
>>>> Existing CH341 boards usually have physical jumpers to switch 
>>>> between the 3 modes.
>>>> 
>>>> This reverts commit 46ee4abb10a07bd8f8ce910ee6b4ae6a947d7f63.
>>> 
>>> You can't just revert something which people clearly depend on
>>> and therefore added to the kernel in the first place.
>> 
>> That device in UART mode was already supported by the serial
>> driver. The original submitter just had to move a jumper on his
>> board. There was no need to patch the kernel.
> 
> How do you know that the author used a dev board? And are you really 
> sure that there are no devices out there which always operate in
> this mode?

The author of commit 46ee4abb10a07bd8 put a link to his device. I have 
the same one (or a clone) and it works fine in serial mode without the patch.
I have a different model that works the same way. A jumper selects the mode.

I can't be sure that no one has ever built a board with that chip, selecting
the wrong mode. But the chip is about 10 years old now; someone would have noticed.

> 
>> That product ID also supports UART but in a limited way, as only
>> the RX and TX pins are available. However it is the only one that
>> supports i2c/spi/gpio, and that's why I have to revert the patch.
> 
> I understand why you did it. My point is that you cannot just claim
> that PID and say that it's only to be used for I2C/SPI without even
> trying to make a case for why that should be ok.

That's the only PID that works for I2C/SPI/GPIO. Right now the serial driver is 
claiming it. I don't know what else to say. If I can't revert that patch, my driver
can't be used without blacklisting the serial driver.

> 
>> If that's desired, the new driver could add support for that as
>> well, but I don't think it's worth the effort.
> 
> We obviously don't want a second serial driver for these devices.
> 
>>> Can you reprogram the device with a newly allocated PID to be
>>> used for i2c-only instead?
>> 
>> It is possible if the device has an SPI flash connected to it, but
>> none of the cheap boards have that.
> 
> That's unfortunate. In principle, your approach is the right one,
> that is, to use a dedicated PID do determine when to configure an
> alternate mode. But since we already know that some people are using
> the PID in question in serial mode, it's not that clear cut.
> 
> How do you intend to switch between i2c and spi mode?

i2c, spi and gpio can all be used simultaneously. I have a working spi implementation,
but I'm still testing it. Basically if a user wants to use spi, then 3 specific gpios
will be reserved for MOSI/MISO/CLK (using gpiochip_request_own_desc), with possibly 
one or more used for the chip select. 
How a user books spi is up in the air right now. That might be done through a sysfs command.

Frank.