Re: [PATCH 5/9] arm64: dts: rockchip: add rk3568 tsadc nodes

From: Heiko Stübner
Date: Wed Jul 28 2021 - 11:31:57 EST

Am Mittwoch, 28. Juli 2021, 17:14:17 CEST schrieb Peter Geis:
> On Wed, Jul 28, 2021 at 10:46 AM Heiko Stübner <heiko@xxxxxxxxx> wrote:
> >
> > Am Mittwoch, 28. Juli 2021, 15:55:30 CEST schrieb Peter Geis:
> > > Add the thermal and tsadc nodes to the rk3568 device tree.
> > > There are two sensors, one for the cpu, one for the gpu.
> > >
> > > Signed-off-by: Peter Geis <pgwipeout@xxxxxxxxx>
> > > ---
> > > .../boot/dts/rockchip/rk3568-pinctrl.dtsi | 6 ++
> > > arch/arm64/boot/dts/rockchip/rk356x.dtsi | 71 +++++++++++++++++++
> > > 2 files changed, 77 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi b/arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi
> > > index a588ca95ace2..b464c7bda1f7 100644
> > > --- a/arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi
> > > +++ b/arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi
> > > @@ -2420,6 +2420,12 @@ spi3m1_cs1: spi3m1-cs1 {
> > > };
> > >
> > > tsadc {
> > > + /omit-if-no-ref/
> > > + tsadc_gpio: tsadc-gpio {
> > > + rockchip,pins =
> > > + <0 RK_PA1 0 &pcfg_pull_none>;
> > > + };
> > > +
> > > /omit-if-no-ref/
> > > tsadcm0_shut: tsadcm0-shut {
> > > rockchip,pins =
> > > diff --git a/arch/arm64/boot/dts/rockchip/rk356x.dtsi b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> > > index 77c679304916..0905fac0726a 100644
> > > --- a/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> > > +++ b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> > > @@ -51,6 +51,7 @@ cpu0: cpu@0 {
> > > compatible = "arm,cortex-a55";
> > > reg = <0x0 0x0>;
> > > clocks = <&scmi_clk 0>;
> > > + #cooling-cells = <2>;
> > > enable-method = "psci";
> > > operating-points-v2 = <&cpu0_opp_table>;
> > > };
> > > @@ -59,6 +60,7 @@ cpu1: cpu@100 {
> > > device_type = "cpu";
> > > compatible = "arm,cortex-a55";
> > > reg = <0x0 0x100>;
> > > + #cooling-cells = <2>;
> > > enable-method = "psci";
> > > operating-points-v2 = <&cpu0_opp_table>;
> > > };
> > > @@ -67,6 +69,7 @@ cpu2: cpu@200 {
> > > device_type = "cpu";
> > > compatible = "arm,cortex-a55";
> > > reg = <0x0 0x200>;
> > > + #cooling-cells = <2>;
> > > enable-method = "psci";
> > > operating-points-v2 = <&cpu0_opp_table>;
> > > };
> > > @@ -75,6 +78,7 @@ cpu3: cpu@300 {
> > > device_type = "cpu";
> > > compatible = "arm,cortex-a55";
> > > reg = <0x0 0x300>;
> > > + #cooling-cells = <2>;
> > > enable-method = "psci";
> > > operating-points-v2 = <&cpu0_opp_table>;
> > > };
> > > @@ -774,6 +778,73 @@ uart9: serial@fe6d0000 {
> > > status = "disabled";
> > > };
> > >
> > > + thermal_zones: thermal-zones {
> > > + cpu_thermal: cpu-thermal {
> > > + polling-delay-passive = <100>;
> > > + polling-delay = <1000>;
> > > +
> > > + thermal-sensors = <&tsadc 0>;
> > > +
> > > + trips {
> > > + cpu_alert0: cpu_alert0 {
> > > + temperature = <70000>;
> > > + hysteresis = <2000>;
> > > + type = "passive";
> > > + };
> > > + cpu_alert1: cpu_alert1 {
> > > + temperature = <75000>;
> > > + hysteresis = <2000>;
> > > + type = "passive";
> > > + };
> > > + cpu_crit: cpu_crit {
> > > + temperature = <95000>;
> > > + hysteresis = <2000>;
> > > + type = "critical";
> > > + };
> > > + };
> > > +
> > > + cooling-maps {
> > > + map0 {
> > > + trip = <&cpu_alert0>;
> > > + cooling-device =
> > > + <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> > > + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> > > + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> > > + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> > > + };
> > > + };
> > > + };
> > > +
> > > + gpu_thermal: gpu-thermal {
> > > + polling-delay-passive = <20>; /* milliseconds */
> > > + polling-delay = <1000>; /* milliseconds */
> > > +
> > > + thermal-sensors = <&tsadc 1>;
> > > + };
> > > + };
> > > +
> > > + tsadc: tsadc@fe710000 {
> > > + compatible = "rockchip,rk3568-tsadc";
> > > + reg = <0x0 0xfe710000 0x0 0x100>;
> > > + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
> > > + assigned-clocks = <&cru CLK_TSADC_TSEN>, <&cru CLK_TSADC>;
> > > + assigned-clock-rates = <17000000>, <700000>;
> > > + clocks = <&cru CLK_TSADC>, <&cru PCLK_TSADC>;
> > > + clock-names = "tsadc", "apb_pclk";
> > > + resets = <&cru SRST_TSADC>, <&cru SRST_P_TSADC>,
> > > + <&cru SRST_TSADCPHY>;
> > > + reset-names = "tsadc", "tsadc-apb", "tsadc-phy";
> > > + rockchip,grf = <&grf>;
> > > + rockchip,hw-tshut-temp = <95000>;
> > > + rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
> > > + rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
> > > + pinctrl-names = "gpio", "otpout";
> > > + pinctrl-0 = <&tsadc_gpio>;
> > > + pinctrl-1 = <&tsadc_shutorg>;
> >
> > The mainline thermal driver doesn't specify these pinctrl states at all.
> >
> > Heiko
>
> Oh, yes this seems to be the case.
>
> Is this something that should get fixed?
> In practice it likely won't ever cause problems, but in theory if
> someone changed the pinmux mode it could break it.

take a look at for example the rk3399.dtsi where the tsadc uses
the generic pinctrl names of "init" (before-probe), "default" (after probe)
and "sleep"


Heiko

>
> >
> > > + #thermal-sensor-cells = <1>;
> > > + status = "disabled";
> > > + };
> > > +
> > > saradc: saradc@fe720000 {
> > > compatible = "rockchip,rk3568-saradc", "rockchip,rk3399-saradc";
> > > reg = <0x0 0xfe720000 0x0 0x100>;
> > >
> >
> >
> >
> >
>