[PATCH v2 2/2] arm64: dts: rockchip: rk3568-evb1-v10: add ethernet support

From: Michael Riesch
Date: Thu Jul 29 2021 - 05:40:00 EST


Signed-off-by: Michael Riesch <michael.riesch@xxxxxxxxxxxxxx>
---
v2:
- sort properties alphabetically
- use phy-mode "rgmii-id" without delay properties
- rename phy nodes to "ethernet-phy"

.../boot/dts/rockchip/rk3568-evb1-v10.dts | 57 +++++++++++++++++++
1 file changed, 57 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
index 69786557093d..65e536c78d2e 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
@@ -13,6 +13,11 @@
model = "Rockchip RK3568 EVB1 DDR4 V10 Board";
compatible = "rockchip,rk3568-evb1-v10", "rockchip,rk3568";

+ aliases {
+ ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
+ };
+
chosen: chosen {
stdout-path = "serial2:1500000n8";
};
@@ -67,6 +72,58 @@
};
};

+&gmac0 {
+ assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
+ assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>;
+ assigned-clock-rates = <0>, <125000000>;
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy0>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac0_miim
+ &gmac0_tx_bus2
+ &gmac0_rx_bus2
+ &gmac0_rgmii_clk
+ &gmac0_rgmii_bus>;
+ status = "okay";
+};
+
+&gmac1 {
+ assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+ assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>;
+ assigned-clock-rates = <0>, <125000000>;
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy1>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m1_miim
+ &gmac1m1_tx_bus2
+ &gmac1m1_rx_bus2
+ &gmac1m1_rgmii_clk
+ &gmac1m1_rgmii_bus>;
+ status = "okay";
+};
+
+&mdio0 {
+ rgmii_phy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x0>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <100000>;
+ reset-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x0>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <100000>;
+ reset-gpios = <&gpio2 RK_PD1 GPIO_ACTIVE_LOW>;
+ };
+};
+
&sdhci {
bus-width = <8>;
max-frequency = <200000000>;
--
2.20.1