Re: [PATCH v1 1/2] i2c:busses:Register PCI1XXXX adapter to I2C subsystem

[LakshmiPraveen Kopparthi]

On Wed, 2021-09-29 at 19:12 +0200, Michał Mirosław wrote:
> [Some people who received this message don't often get email from
> mirq-linux@xxxxxxxxxxxx. Learn why this is important at 
> http://aka.ms/LearnAboutSenderIdentification.]
> 
> EXTERNAL EMAIL: Do not click links or open attachments unless you
> know the content is safe
> 
> On Wed, Sep 29, 2021 at 11:52:14AM +0530, LakshmiPraveen Kopparthi
> wrote:
> > Register the adapter to the I2C subsystem. Also the power
> > management
> > routines are added.
> [...]
> > --- /dev/null
> > +++ b/drivers/i2c/busses/i2c-mchp-pci1xxxx.c
> > @@ -0,0 +1,616 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/*
> > + * Microchip PCI1XXXX I2C adapter driver for PCIe Switch
> > + * which has I2C controller in one of its downstream functions
> > + *
> > + * * Copyright 2020-2021 Microchip Technology, Inc
> > + *
> > + * Author: LakshmiPraveen Kopparthi <
> > LakshmiPraveen.Kopparthi@xxxxxxxxxxxxx>
> > + */
> 
> Is there a datasheet you can link to? Some register bits have cryptic
> names
> that might not be understandable without the DS.

There is no datasheet available yet.I can try to modify some bit names
for better understanding.Can you tell me which ones seem cryptic to you
?   

> [...]
> > +#define BAR0    0
> > +#define BAR1    1
> > +#define BAR2    2
> > +#define BAR3    3
> 
> Those don't add much value and only BAR0 is actually used.

Ok.I will remove the other bar defines.

> 
> [...]
> > +#define SMB_CORE_CTRL_ESO            (0x40)
> > +#define SMB_CORE_CTRL_FW_ACK         (0x10)
> 
> Those parentheses are not needed.

ok. Got it.

> 
> [...]
> > +#define I2C_FOD_EN           (0x10)
> > +#define I2C_PULL_UP_EN               (0x08)
> > +#define I2C_PULL_DOWN_EN     (0x04)
> > +#define I2C_INPUT_EN         (0x02)
> > +#define I2C_OUTPUT_EN                (0x01)
> 
> I guess the HW can do pull-ups, but the driver doesn't support that.
> Is it
> on purpose?

Yes. Internal pull-ups are not used for this device. Pull-ups are
connected externally at the board level.

> 
> [...]
> > +#define PCI1XXXX_I2C_TIMEOUT (msecs_to_jiffies(1000))
> 
> Define the timeout (in ms) and add msecs_to_jiffies() at the use site
> where needed. But... it doesn't seem to be used?

Sure. Will change it. This is used in the second patch(2/2). As
suggested in your last comment, I will merge the two patches into a
single one.  

> 
> [...]
> > +struct pci1xxxx_i2c {
> > +     struct i2c_adapter adap;
> > +     struct device *dev;
> 
> I think you can use adap.dev.parent for this.

Ok. Got it.

> 
> [...]
> > +static irqreturn_t pci1xxxx_i2c_isr(int irq, void *dev)
> > +{
> > +     struct pci1xxxx_i2c *i2c = dev;
> > +     bool intr_handled = false;
> > +     unsigned long flags;
> > +     u16 regval;
> > +     u8 regval1;
> > +
> > +     spin_lock_irqsave(&i2c->lock, flags);
> 
> This is hardirq context, so spin_lock() is enough. But, it looks like
> nothing
> else uses this lock so it's eithier superfluous or missing somewhere
> else.

Ok. But there are some registers that are read and updated in the ISR
and in the foreground.
I will add the lock for these register access.

> 
> > +     /* Mask the interrupt */
> > +     regval = readw(i2c->i2c_base + SMBUS_GEN_INT_MASK_REG_OFF);
> > +     regval |= (SMBALERT_INTR_MASK | I2C_BUF_MSTR_INTR_MASK);
> > +     writew(regval, (i2c->i2c_base + SMBUS_GEN_INT_MASK_REG_OFF));
> 
> No need to mask and unmask the interrupt as it will be blocked anyway
> until the ISR returns.

Ok.Got it.

> 
> > +     /*
> > +      * Read the SMBus interrupt status register to see if the
> > +      * DMA_TERM interrupt has caused this callback
> > +      */
> > +     regval = readw(i2c->i2c_base + SMBUS_GEN_INT_STAT_REG_OFF);
> > +
> > +     if (regval & I2C_BUF_MSTR_INTR_MASK) {
> > +             regval1 = readb(i2c->i2c_base +
> > SMBUS_INTR_STAT_REG_OFF);
> > +             if (regval1 & INTR_STAT_DMA_TERM) {
> > +                     complete(&i2c->i2c_xfer_done);
> > +                     intr_handled = true;
> > +                     writeb(INTR_STAT_DMA_TERM,
> > +                            (i2c->i2c_base +
> > SMBUS_INTR_STAT_REG_OFF));
> > +             }
> > +             /* ACK the high level interrupt */
> > +             writew(I2C_BUF_MSTR_INTR_MASK,
> > +                    (i2c->i2c_base + SMBUS_GEN_INT_STAT_REG_OFF));
> 
> You already have pci1xxxx_ack_high_level_intr() - why not use or
> delete it?

Ok.I will use it.

> 
> > +     }
> > +
> > +     if (regval & SMBALERT_INTR_MASK) {
> > +             intr_handled = true;
> > +             /* ACK the high level interrupt */
> > +             writew(SMBALERT_INTR_MASK,
> > +                    (i2c->i2c_base + SMBUS_GEN_INT_STAT_REG_OFF));
> 
> Nothing is done with the interrupt here - why enable it, then?

It is not enabled anywhere in the driver. I will remove this code.  

> 
> > +     }
> > +
> > +     regval = readw(i2c->i2c_base + SMBUS_GEN_INT_MASK_REG_OFF);
> > +     /* UnMask the interrupt */
> > +     regval &= ~(I2C_BUF_MSTR_INTR_MASK | SMBALERT_INTR_MASK);
> > +     writew(regval, (i2c->i2c_base + SMBUS_GEN_INT_MASK_REG_OFF));
> > +
> > +     spin_unlock_irqrestore(&i2c->lock, flags);
> > +
> > +     if (intr_handled)
> > +             return IRQ_HANDLED;
> > +     else
> > +             return IRQ_NONE;
> > +}
> [...]
> > +static void pci1xxxx_i2c_set_freq(struct pci1xxxx_i2c *i2c)
> > +{
> > +     /*
> > +      * The SMB core needs specific values to be set in the
> > BUS_CLK register
> > +      * for the corresponding frequency
> > +      */
> > +     switch (i2c->freq) {
> > +     case I2C_MAX_STANDARD_MODE_FREQ:
> > +             writeb(SR_HOLD_TIME_100KHZ,
> > +                    (i2c->i2c_base +
> > SMB_CORE_SR_HOLD_TIME_REG_OFF));
> > +             writel(SMB_IDLE_SCALING_100KHZ,
> > +                    (i2c->i2c_base +
> > SMB_CORE_IDLE_SCALING_REG_OFF));
> > +             writew(BUS_CLK_100KHZ,
> > +                    (i2c->i2c_base + SMB_CORE_BUS_CLK_REG_OFF));
> > +             writel(CLK_SYNC_100KHZ,
> > +                    (i2c->i2c_base + SMB_CORE_CLK_SYNC_REG_OFF));
> > +             writel(DATA_TIMING_100KHZ,
> > +                    (i2c->i2c_base +
> > SMB_CORE_DATA_TIMING_REG_OFF));
> > +             writel(TO_SCALING_100KHZ,
> > +                    (i2c->i2c_base +
> > SMB_CORE_TO_SCALING_REG_OFF));
> > +             break;
> > +
> > +     case I2C_MAX_FAST_MODE_PLUS_FREQ:
> [...]
> 
> Is it necessary to limit the frequencies to the three specified?
> Can't the
> register values be calculated based on the exact frequency requested?
> It is
> sometimes needed to run the bus at a lower frequency due to
> electrical or
> chip design issues.

ok. I will look into it and try to add the support for all the
frequencies.

> 
> [...]
> > +/*
> > + * We could have used I2C_FUNC_SMBUS_EMUL but that includes
> > + * SMBUS_QUICK as well.We dnt support SMBUS_QUICK hence the
> > + * need for a lengthy funcs callback
> > + */
> 
> You could say: I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK. But
> there are also more missing bits like PEC. BTW, is the hardware
> not able to handle zero-sized transfer?

Ok. This module supports only the flags mentioned in the driver. In
case of zero sized transfer, yes, the hardware does support zero sized
transfer.

> 
> > +static const struct i2c_adapter pci1xxxx_i2c_ops = {
> > +     .owner  = THIS_MODULE,
> > +     .name   = "Pci1xxxx I2c Adapter",
> 
> I2C

ok.Got it.

> 
> > +     .algo   = &pci1xxxx_i2c_algo,
> > +};
> > 
> > +static int pci1xxxx_i2c_suspend(struct device *dev)
> > +{
> > +     struct pci1xxxx_i2c *i2c = dev_get_drvdata(dev);
> > +     struct pci_dev *pdev = to_pci_dev(dev);
> > +     u32 regval;
> > +
> > +     i2c_mark_adapter_suspended(&i2c->adap);
> > +
> > +     pci1xxxx_ack_high_level_intr(i2c, ALL_HIGH_LAYER_INTR);
> 
> There should be no active interrupt signals, unless they can wait
> until
> resume for servicing. Either way, acking them blankly looks
> suspicious.
> i2c_mark_adapter_suspended() should guarantee there are no transfers
> coming (or being serviced) after it returns.

ok. I will modify it.

> 
> > +     pci1xxxx_i2c_config_high_level_intr(i2c, ALL_HIGH_LAYER_INTR,
> > false);
> > +
> > +     /*
> > +      * Enable the PERST_DIS bit to mask the PERST from
> > +      * resetting the core regs
> > +      */
> > +     regval = readl(i2c->i2c_base + SMBUS_RESET_REG);
> > +     regval |= PERI_SMBUS_D3_RESET_DIS;
> > +     writel(regval, i2c->i2c_base + SMBUS_RESET_REG);
> > +
> > +     return 0;
> > +}
> > 
> > +static int pci1xxxx_i2c_resume(struct device *dev)
> > +{
> > +     struct pci1xxxx_i2c *i2c = dev_get_drvdata(dev);
> > +     struct pci_dev *pdev = to_pci_dev(dev);
> > +     u32 regval;
> > +
> > +     i2c_mark_adapter_resumed(&i2c->adap);
> 
> This should go at the end, after preparing the HW. BTW, the interrupt
> config is not restored.

Ok. I will modify it. 

> 
> > +
> > +     regval = readl(i2c->i2c_base + SMBUS_RESET_REG);
> > +     regval &= ~PERI_SMBUS_D3_RESET_DIS;
> > +     writel(regval, i2c->i2c_base + SMBUS_RESET_REG);
> > +
> > +     return 0;
> > +}
> > +
> > +static SIMPLE_DEV_PM_OPS(pci1xxxx_i2c_pm_ops,
> > pci1xxxx_i2c_suspend,
> > +                      pci1xxxx_i2c_resume);
> > +
> > +static int pci1xxxx_i2c_probe_pci(struct pci_dev *pdev,
> > +                               const struct pci_device_id *ent)
> > +{
> > +     struct pci1xxxx_i2c *i2c;
> > +     int ret;
> > +
> > +     i2c = devm_kzalloc(&pdev->dev, sizeof(*i2c), GFP_KERNEL);
> > +     if (!i2c)
> > +             return -ENOMEM;
> > +
> > +     i2c->dev = &pdev->dev;
> > +
> > +     pci_set_drvdata(pdev, i2c);
> > +     ret = pcim_enable_device(pdev);
> > +     if (ret)
> > +             return ret;
> > +
> > +     ret = pci_request_regions(pdev, pci_name(pdev));
> > +     if (ret)
> > +             return ret;
> > +
> > +     /*
> > +      * We are getting the base address of the SMB core. SMB core
> > uses
> > +      * BAR0 and 32K is the size here pci_resource_len returns 32K
> > by
> > +      * reading BAR0
> > +      */
> > +
> > +     i2c->i2c_base = pcim_iomap(pdev, BAR0, pci_resource_len(pdev,
> > BAR0));
> 
> pcim_iomap_regions()

ok.Got it.

> 
> > +     if (!i2c->i2c_base) {
> > +             ret = -ENOMEM;
> > +             goto err_free_region;
> > +     }
> > +
> > +     ret = pci_alloc_irq_vectors(pdev, 1, 1, PCI_IRQ_ALL_TYPES);
> > +     if (ret < 0)
> > +             goto err_free_region;
> > +
> > +     i2c->irq = pci_irq_vector(pdev, 0);
> 
> 'irq' field doesn't seem to be used past the request_irq(), so maybe
> can
> be removed?

Ok.I will remove it.

> 
> > +     /* Register the isr. we are not using any isr flags here */
> > +     ret = devm_request_irq(&pdev->dev, i2c->irq,
> > pci1xxxx_i2c_isr,
> > +                            PCI1XXXX_IRQ_FLAGS,
> > +                            pci_name(pdev), i2c);
> > [...]
> > 
> > +     pci_set_master(pdev);
> > +
> > +     init_completion(&i2c->i2c_xfer_done);
> > +
> > +     spin_lock_init(&i2c->lock);
> > +
> > +     pci1xxxx_i2c_init(i2c);
> 
> This all should be done before request_irq().

ok. I will update it.

> 
> > +     i2c->adap = pci1xxxx_i2c_ops;
> > +
> > +     i2c->adap.class = I2C_CLASS_SPD;
> > +     i2c->adap.dev.parent = &pdev->dev;
> > +
> > +     snprintf(i2c->adap.name, sizeof(i2c->adap.name),
> > +              "MCHP PCI1xxxx i2c adapter at %s", pci_name(pdev));
> > +
> > +     i2c_set_adapdata(&i2c->adap, i2c);
> > +
> > +     ret = i2c_add_adapter(&i2c->adap);
> > +     if (ret) {
> > +             dev_err(&pdev->dev, "i2c add adapter failed = %d\n",
> > ret);
> > +             goto err_free_region;
> > +     }
> > +
> > +     return 0;
> > +
> > +err_free_region:
> > +     pci_release_regions(pdev);
> > +     return ret;
> > +}
> [...]
> 
> It would be better to have the driver in one patch, than split in
> two.

Ok.Got it.

> 
> Best Regards
> Michał Mirosław