Hi Andrew,
On 22/09/23 09:52, MD Danish Anwar wrote:
On 21/09/23 22:57, Andrew Davis wrote:
On 9/21/23 1:09 AM, MD Danish Anwar wrote:
ICSSG2 provides dual Gigabit Ethernet support.
For support SR2.0 ICSSG Ethernet firmware:
- provide different firmware blobs and use TX_PRU.
- IEP0 is used as PTP Hardware Clock and can only be used for one port.
- TX timestamp notification comes via INTC interrupt.
Signed-off-by: MD Danish Anwar <danishanwar@xxxxxx>
---
arch/arm64/boot/dts/ti/Makefile | 4 +-
...se-board.dts => k3-am654-common-board.dts} | 0
arch/arm64/boot/dts/ti/k3-am654-icssg2.dtso | 145 ++++++++++++++++++
3 files changed, 148 insertions(+), 1 deletion(-)
rename arch/arm64/boot/dts/ti/{k3-am654-base-board.dts =>
k3-am654-common-board.dts} (100%)
create mode 100644 arch/arm64/boot/dts/ti/k3-am654-icssg2.dtso
diff --git a/arch/arm64/boot/dts/ti/Makefile
b/arch/arm64/boot/dts/ti/Makefile
index e7b8e2e7f083..85c91f5e832e 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -42,12 +42,14 @@ dtb-$(CONFIG_ARCH_K3) +=
k3-am642-tqma64xxl-mbax4xxl-sdcard.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am642-tqma64xxl-mbax4xxl-wlan.dtb
# Boards with AM65x SoC
-k3-am654-gp-evm-dtbs := k3-am654-base-board.dtb
k3-am654-base-board-rocktech-rk101-panel.dtbo
+k3-am654-gp-evm-dtbs := k3-am654-common-board.dtb
k3-am654-base-board-rocktech-rk101-panel.dtbo
Should the k3-am654-gp-evm.dtb not also have this icssg2 support? Does
it work
to keep this line like before or is there some conflict having both
enabled?
I have not tested this dtb (k3-am654-gp-evm.dtb). So just to be on the
safe side I kept gp-evm.dtb as it was. Ideally gp-evm.dtb should have
icssg2 support as well. But I haven't tested the combination of
base-board + icssg dtbo + rockteck dtbo. That is why I kept gp-evm dtb
as it was. Anyways, for ICSSG2's use case only k3-am654-base-board.dtb
is used so I think it's ok to leave k3-am654-gp-evm.dtb to as it was.
Andrew
I tested AM654x-GP EVM with k3-am654-gp-evm.dtb with both the
combination below (having k3-am654-base-board-dtbs :=
k3-am654-common-board.dtb k3-am654-icssg2.dtbo), ICSSG worked fine in
both the scenarios and I didn't see any issue. I don't have a rocktech
panel with me so couldn't test that. But as far as ICSSG is concerned it
works fine with the both the combinations. Please let me know which one
should I use. Should I keep gp-evm as it is (use dtb without the icssg2
overlay) or should I add icssg2 overlay in gp-evm.dtb as well.
1. k3-am654-gp-evm-dtbs := k3-am654-base-board.dtb
k3-am654-base-board-rocktech-rk101-panel.dtbo
2. k3-am654-gp-evm-dtbs := k3-am654-common-board.dtb
k3-am654-base-board-rocktech-rk101-panel.dtbo