[PATCH 3/3] arm64: dts: ti: k3-j722s-evm: Update USB0 and USB1 configuration for EVM

[Ravi Gunasekaran]

The GPIO expander on the EVM allows the USB selection for Type-C
port to either USB0 or USB1 via USB hub. By default, let the Type-C
port select USB0 via the GPIO expander port P05.

Enable super-speed on USB1 by updating SerDes0 lane configuration.

Signed-off-by: Ravi Gunasekaran <r-gunasekaran@xxxxxx>
---
 arch/arm64/boot/dts/ti/k3-j722s-evm.dts | 58 +++++++++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-serdes.h      |  7 +++
 2 files changed, 65 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j722s-evm.dts b/arch/arm64/boot/dts/ti/k3-j722s-evm.dts
index bf3c246d13d1..ddb4f1f0d92d 100644
--- a/arch/arm64/boot/dts/ti/k3-j722s-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j722s-evm.dts
@@ -9,7 +9,9 @@
 /dts-v1/;
 
 #include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/phy/phy.h>
 #include "k3-j722s.dtsi"
+#include "k3-serdes.h"
 
 / {
 	compatible = "ti,j722s-evm", "ti,j722s";
@@ -20,6 +22,8 @@
 		serial2 = &main_uart0;
 		mmc0 = &sdhci0;
 		mmc1 = &sdhci1;
+		usb0 = &usb0;
+		usb1 = &usb1;
 	};
 
 	chosen {
@@ -202,6 +206,12 @@
 			J722S_IOPAD(0x012c, PIN_OUTPUT, 0) /* (AF25) RGMII1_TX_CTL */
 		>;
 	};
+
+	main_usb1_pins_default: main-usb1-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x0258, PIN_INPUT, 0) /* (B27) USB1_DRVVBUS */
+		>;
+	};
 };
 
 &cpsw3g {
@@ -301,6 +311,14 @@
 				  "PCIe0_1L_RC_RSTz", "PCIe0_1L_PRSNT#",
 				  "ENET1_EXP_SPARE2", "ENET1_EXP_PWRDN",
 				  "PD_I2ENET1_I2CMUX_SELC_IRQ", "ENET1_EXP_RESETZ";
+
+		p05-hog {
+			/* P05 - USB2.0_MUX_SEL */
+			gpio-hog;
+			gpios = <5 GPIO_ACTIVE_LOW>;
+			output-high;
+			line-name = "USB2.0_MUX_SEL";
+		};
 	};
 };
 
@@ -384,3 +402,43 @@
 	status = "okay";
 	bootph-all;
 };
+
+&serdes0_ln_ctrl {
+	idle-states = <J722S_SERDES0_LANE0_USB>,
+		      <J722S_SERDES1_LANE0_PCIE0_LANE0>;
+};
+
+&serdes0 {
+	status = "okay";
+	serdes0_usb_link: phy@0 {
+		reg = <0>;
+		cdns,num-lanes = <1>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_USB3>;
+		resets = <&serdes_wiz0 1>;
+	};
+};
+
+&usbss0 {
+	ti,vbus-divider;
+	status = "okay";
+};
+
+&usb0 {
+	dr_mode = "otg";
+	usb-role-switch;
+};
+
+&usbss1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_usb1_pins_default>;
+	ti,vbus-divider;
+	status = "okay";
+};
+
+&usb1 {
+	dr_mode = "host";
+	maximum-speed = "super-speed";
+	phys = <&serdes0_usb_link>;
+	phy-names = "cdns3,usb3-phy";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-serdes.h b/arch/arm64/boot/dts/ti/k3-serdes.h
index a011ad893b44..9082abeddcb1 100644
--- a/arch/arm64/boot/dts/ti/k3-serdes.h
+++ b/arch/arm64/boot/dts/ti/k3-serdes.h
@@ -201,4 +201,11 @@
 #define J784S4_SERDES4_LANE3_USB		0x2
 #define J784S4_SERDES4_LANE3_IP4_UNUSED		0x3
 
+/* J722S */
+#define J722S_SERDES0_LANE0_USB			0x0
+#define J722S_SERDES0_LANE0_QSGMII_LANE2	0x1
+
+#define J722S_SERDES1_LANE0_PCIE0_LANE0		0x0
+#define J722S_SERDES1_LANE0_QSGMII_LANE1	0x1
+
 #endif /* DTS_ARM64_TI_K3_SERDES_H */
-- 
2.17.1