Tom Eastep wrote:
>
> I'm unable to boot using 2.1.123; booted fine on all kernels since 2.1.115
> including 2.1.123Pre3.
>
> I'm seeing the following on the console:
>
> (scsi0:0:-1:-1) Scanning Channel for devices
> SCSI: Aborting command due to timeout, pid 0, scsi 0, channel 0, id 0, lun 0
> Test Unit Ready 00 00 00 00 00
> SCSI host 0 abort (pid 0) timed out - resetting
> SCSI bus is being reset for host 0 channel 0
> (SCSI0:0:0:0) Device reset, Message buffer in use
> SCSI host 0 channel 0 reset (pid 0) timed out - trying harder
>
> The last 4 messages repeat indefinitely until <ctrl-alt-del>
>
> A normal boot looks as follows:
>
> (scsi0:0:-1:-1) Scanning channel for devices.
> (scsi0:0:0:0) Synchronous at 10.0MHz, offset 15.
> Vendor: SEAGATE Model: ST32550N Rev: 8303
> Type: Direct-Access ANSI SCSI revision: 02
> Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
> Vendor: HP Model: HP35480A Rev: T503
> Type: Sequential-Access ANSI SCSI revision: 02
> Vendor: FUJITSU Model: M2954S-512 Rev: 0147
> Type: Direct-Access ANSI SCSI revision: 02
> Detected scsi disk sdb at scsi0, channel 0, id 4, lun 0
> Vendor: SONY Model: CD-ROM CDU-76S Rev: 1.1c
> Type: CD-ROM ANSI SCSI revision: 02
> Vendor: QUANTUM Model: FIREBALL1280S Rev: 630C
> Type: Direct-Access ANSI SCSI revision: 02
> Detected scsi disk sdc at scsi0, channel 0, id 6, lun 0
> scsi : detected 3 SCSI disks total.
> SCSI device sda: hdwr sector= 512 bytes. Sectors= 4165272 [2033 MB] [2.0 GB]
> (scsi0:0:4:0) Synchronous at 10.0MHz, offset 15.
> SCSI device sdb: hdwr sector= 512 bytes. Sectors= 8498506 [4149 MB] [4.1 GB]
> (scsi0:0:6:0) Synchronous at 10.0MHz, offset 8.
> SCSI device sdc: hdwr sector= 512 bytes. Sectors= 2503872 [1222 MB] [1.2 GB]
>
> System:
>
> HP Vectra XU 6/150 (2x 150 ppro, KX Chipset)
> 128mb
> Matrox Millennium I - 2mb
> Onboard AIC-7880U - firmware version 1.2
>
Pardon me for replying to my own post but I have additional information. This
morning, I built a UP 2.1.123 and it booted successfully. FWIW, I've attached
dmesg output from booting 2.1.122.
When I get the time, I'll try to isolate the patch that's causing the problem.
-Tom
-- Tom Eastep COMPAQ Computer Corporation Enterprise Computing Group Tandem Division tom.eastep@compaq.com --------------87C83E170D04B0CF1313A81B Content-Type: text/plain; charset=us-ascii; name="dmesg122" Content-Transfer-Encoding: 7bit Content-Disposition: inline; filename="dmesg122"Linux version 2.1.122 (eastep@hozomeen.loc551.tandem.com) (gcc version egcs-2.90.29 980515 (egcs-1.0.3 release)) #1 SMP Fri Sep 18 11:29:53 PDT 1998 Intel MultiProcessor Specification v1.1 Virtual Wire compatibility mode. OEM ID: HP Product ID: XX APIC at: 0xFEE00000 Processor #1 Pentium(tm) Pro APIC version 17 Processor #0 Pentium(tm) Pro APIC version 17 I/O APIC #16 Version 17 at 0xFEC00000. Processors: 2 mapped APIC to ffffe000 (fee00000) mapped IOAPIC to ffffd000 (fec00000) vesafb_setup: option redraw Console: colour dummy device 80x25 Calibrating delay loop... 149.50 BogoMIPS Memory: 128048k/131072k available (776k kernel code, 412k reserved, 1784k data, 52k init) Checking 386/387 coupling... OK, FPU using exception 16 error reporting. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.24 (19980910) Richard Gooch (rgooch@atnf.csiro.au) CPU1: Intel Pentium Pro stepping 02 calibrating APIC timer ... ..... CPU clock speed is 150.0709 MHz. ..... APIC bus clock speed is 60.0281 MHz. Booting processor 0 eip 2000 Calibrating delay loop... 149.91 BogoMIPS OK. CPU0: Intel Pentium Pro stepping 02 Total of 2 processors activated (299.42 BogoMIPS). enabling symmetric IO mode... ...done. ENABLING IO-APIC IRQs init IO_APIC IRQs IO-APIC pin 0 not connected. number of MP IRQ sources: 15. number of IO-APIC registers: 16. testing the IO APIC....................... .... register #00: 00000000 ....... : physical APIC id: 00 .... register #01: 000F0011 ....... : max redirection entries: 000F ....... [IO-APIC cannot route PCI PIRQ 0-3] ....... : IO APIC version: 0011 .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 0FF 0F 0 0 0 0 0 1 1 59 02 0FF 0F 0 0 0 0 0 1 1 51 03 0FF 0F 0 0 0 0 0 1 1 61 04 0FF 0F 0 0 0 0 0 1 1 69 05 0FF 0F 0 0 0 0 0 1 1 71 06 0FF 0F 0 0 0 0 0 1 1 79 07 0FF 0F 0 0 0 0 0 1 1 81 08 0FF 0F 0 0 0 0 0 1 1 89 09 0FF 0F 0 0 0 0 0 1 1 91 0a 0FF 0F 0 0 0 0 0 1 1 99 0b 0FF 0F 0 0 0 0 0 1 1 A1 0c 0FF 0F 0 0 0 0 0 1 1 A9 0d 000 00 1 0 0 0 0 0 0 00 0e 0FF 0F 0 0 0 0 0 1 1 B1 0f 0FF 0F 0 0 0 0 0 1 1 B9 IRQ to pin mappings: 0->2 1->1 2->-1 3->3 4->4 5->5 6->6 7->7 8->8 9->9 10->10 11->11 12->12 13->13 14->14 15->15 16->-1 17->-1 18->-1 19->-1 20->-1 21->-1 22->-1 23->-1 24->-1 25->-1 26->-1 27->-1 28->-1 29->-1 30->-1 31->-1 32->-1 33->-1 34->-1 35->-1 36->-1 37->-1 38->-1 39->-1 40->-1 41->-1 42->-1 43->-1 44->-1 45->-1 46->-1 47->-1 48->-1 49->-1 50->-1 51->-1 52->-1 53->-1 54->-1 55->-1 56->-1 57->-1 58->-1 59->-1 60->-1 61->-1 62->-1 63->-1 .................................... done. PCI: PCI BIOS revision 2.00 entry at 0xfbe50 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Device 00:a0 not found by BIOS PCI: Device 00:c8 not found by BIOS Swansea University Computer Society NET3.039 for Linux 2.1 Swansea University Computer Society TCP/IP for NET3.037 IP Protocols: ICMP, UDP, TCP Starting kswapd v 1.5 vesafb: 1280x1024x8, linelength=1280 vesafb: framebuffer at 0xa0800000, mapped to 0xc8800000, size 1310720 vesafb: scrolling=redraw Console: switching to colour frame buffer device 160x64 fb0: VESA VGA frame buffer device pty: 256 Unix98 ptys configured PS/2 auxiliary pointing device detected -- driver installed. (scsi0) <Adaptec AIC-7880 Ultra SCSI host adapter> found at PCI 2/0 (scsi0) Narrow Channel, SCSI ID=7, 16/255 SCBs (scsi0) BIOS disabled, IO Port 0xf800, IRQ 10 (scsi0) IO Memory at 0xfffdc000, MMAP Memory at 0xc8941000 (scsi0) Resetting channel (scsi0) Downloading sequencer code... 413 instructions downloaded scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.0.20/3.2.4 <Adaptec AIC-7880 Ultra SCSI host adapter> scsi : 1 host. (scsi0:0:-1:-1) Scanning channel for devices. (scsi0:0:0:0) Synchronous at 10.0MHz, offset 15. Vendor: SEAGATE Model: ST32550N Rev: 8303 Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sda at scsi0, channel 0, id 0, lun 0 Vendor: HP Model: HP35480A Rev: T503 Type: Sequential-Access ANSI SCSI revision: 02 Vendor: FUJITSU Model: M2954S-512 Rev: 0147 Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sdb at scsi0, channel 0, id 4, lun 0 Vendor: SONY Model: CD-ROM CDU-76S Rev: 1.1c Type: CD-ROM ANSI SCSI revision: 02 Vendor: QUANTUM Model: FIREBALL1280S Rev: 630C Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sdc at scsi0, channel 0, id 6, lun 0 scsi : detected 3 SCSI disks total. SCSI device sda: hdwr sector= 512 bytes. Sectors= 4165272 [2033 MB] [2.0 GB] (scsi0:0:4:0) Synchronous at 10.0MHz, offset 15. SCSI device sdb: hdwr sector= 512 bytes. Sectors= 8498506 [4149 MB] [4.1 GB] (scsi0:0:6:0) Synchronous at 10.0MHz, offset 8. SCSI device sdc: hdwr sector= 512 bytes. Sectors= 2503872 [1222 MB] [1.2 GB] Partition check: sda: sda1 sdb: sdb1 sdb2 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 sdb11 > sdc: sdc1 sdc2 VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 52k freed Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996 SB 4.13 detected OK (220) YM3812 and OPL-3 driver Copyright (C) by Hannu Savolainen, Rob Hooft 1993-1996 st: bufsize 32768, wrt 30720, max buffers 4, s/g segs 16. Detected scsi tape st0 at scsi0, channel 0, id 3, lun 0 NET3: Unix domain sockets 0.16 for Linux NET3.038. eepro100.c:v0.36 10/20/97 Donald Becker linux-eepro100@cesdis.gsfc.nasa.gov Found Intel i82557 PCI Speedo at I/O 0xf000, IRQ 15. PCI latency timer (CFLT) is 0xf8. eepro100.c:v0.36 10/20/97 Donald Becker linux-eepro100@cesdis.gsfc.nasa.gov eth0: Intel EtherExpress Pro 10/100 at 0xf000, 00:A0:C9:15:39:2A, IRQ 15. Board assembly 352509-003, Physical connectors present: RJ45 Primary interface chip DP83840 PHY #1. DP83840 specific setup, setting register 23 to 8462. General self-test: passed. Serial sub-system self-test: passed. Internal registers self-test: passed. ROM checksum self-test: passed (0x49caa8d6). Receiver lock-up workaround activated. eth0: speedo_open() irq 15. eth0: Done speedo_open(), status 00000090. hp100: eth1: HP J2585A at 0xf400, IRQ 11, PCI bus, 128k SRAM (rx/tx 75%). hp100: eth1: Memory area at 0xfffcc000-0xfffebfff (virtual base 0xc8997000). hp100: eth1: Adapter is attached to 10Mb/s network.
--------------87C83E170D04B0CF1313A81B--
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu Please read the FAQ at http://www.tux.org/lkml/