NFS/RPC warnings: 2.1.131-ac7 alpha arch.

Frederick (niles@axp745.gsfc.nasa.gov)
Fri, 11 Dec 98 00:06:36 -0500

I used to get the warning messages regarding RPC/NFS mounting shown at
the end of this msg in the 2.1.8x or so series for the x86 arch, but
that's been gone for about a month on that arch. It seems to be still
present on the alpha arch. There's a few other warnings too. Why am I
getting two ethernet devices? Is frame buffer support mean anything
under alpha arch? I can't get it to do anything special with my
trident card.

When running "make xconfig" using this kernel the X bnffer seemed to
get a bit corrupted, and then after building a fresh kernel under this
kernel and then attempting to "shutdown -r now", the kernel crashed...
I didn't write down the trackback, but I'll do it next time. This is
the first 2.1.x kernel I've gotten to work at all though. Thanks
all... Although I only started trying a few kernels ago...

Thanks,
Rick Niles.

-----
Linux version 2.1.131 (root@alpha.localdomain) (gcc version egcs-2.91.59 19981124 (egcs-1.1.1 pre-release #3)) #11 Mon Dec 10 20:40:51 EST 2018
Booting on Avanti using machine vector Avanti
Command line: bootdevice=sda2 bootfile=/vmlinux-test.gz root=/dev/sda2
HWRPB cycle frequency bogus. Estimating... 233326324 Hz
Console: colour VGA+ 80x25
Calibrating delay loop... 230.16 BogoMIPS
Memory: 94416k available
POSIX conformance testing by UNIFIX
Alpha PCI BIOS32 revision 0.04
PCI: Probing PCI hardware
Swansea University Computer Society NET3.039 for Linux 2.1
NET3: Unix domain sockets 0.16 for Linux NET3.038.
Swansea University Computer Society TCP/IP for NET3.037
IP Protocols: ICMP, UDP, TCP
Starting kswapd v 1.5
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
Floppy drive(s): fd0 is 2.88M
FDC 0 is a National Semiconductor PC87306
ncr53c8xx: at PCI bus 0, device 6, function 0
ncr53c8xx: 53c810 detected
ncr53c810-0: rev=0x02, base=0x4200000, io_port=0x8000, irq=11
ncr53c810-0: ID 7, Fast-10, Parity Checking
ncr53c810-0: restart (scsi reset).
scsi0 : ncr53c8xx - revision 3.1d
scsi : 1 host.
Vendor: QUANTUM Model: LIGHTNING 730S Rev: 2417
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
scsi : detected 1 SCSI disk total.
ncr53c810-0-<0,*>: FAST-10 SCSI 10.0 MB/s (100 ns, offset 8)
SCSI device sda: hdwr sector= 512 bytes. Sectors= 1431518 [698 MB] [0.7 GB]
tulip.c:v0.83 10/19/97 becker@cesdis.gsfc.nasa.gov
eth0: Digital DS21040 Tulip at 0x8800, 00 00 f8 23 48 a3, IRQ 15.
eth1: region already allocated at 0x8800.
Partition check:
sda: sda1 sda2 sda3
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 104k freed
Adding Swap: 30856k swap-space (priority -1)
portmap: RPC call returned error 61
RPC: task of released request still queued!
RPC: (task is on xprt_pending)
portmap: RPC call returned error 61
RPC: task of released request still queued!
RPC: (task is on xprt_pending)
lockd_up: makesock failed, error=-61
portmap: RPC call returned error 61
RPC: task of released request still queued!
RPC: (task is on xprt_pending)
TIOCSER?WILD ioctl obsolete, ignored.
TIOCSER?WILD ioctl obsolete, ignored.

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/