I compiled 2.2.0-pre6 this evening, and found it to work OK:
-- I can mount my FAT32 partition
-- My SCSI devices are detected properly (see below)
I still need to boot my router on this release to make sure the
firewall code is working correctly. I also do not have a lot of
sound-related
software yet, so I can't verify that my GUS MAX is working OK.
------------------------------------
dmesg bits of interest (from my P-120 desktop machine):
Linux version 2.2.0-pre6 (root@bob.home.net) (gcc version 2.7.2.3) #1 Mon
Jan 11 17:59:40 EST 1999
Detected 118953081 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 47.41 BogoMIPS
Memory: 63296k/65536k available (824k kernel code, 412k reserved, 972k data,
32k init)
.
.
(scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 18/0
(scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs
(scsi0) Warning - detected auto-termination
(scsi0) Please verify driver detected settings are correct.
(scsi0) If not, then please properly set the device termination
(scsi0) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted
(scsi0) during machine bootup.
(scsi0) Cables present (Int-50 YES, Int-68 NO, Ext-68 YES)
(scsi0) Downloading sequencer code... 419 instructions downloaded
(scsi1) <Adaptec AHA-2944 Ultra SCSI host adapter> found at PCI 19/0
(scsi1) Wide Channel, SCSI ID=7, 16/255 SCBs
(scsi1) Warning - detected auto-termination
(scsi1) Please verify driver detected settings are correct.
(scsi1) If not, then please properly set the device termination
(scsi1) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted
(scsi1) during machine bootup.
(scsi1) Cables present (Int-50 NO, Int-68 NO, Ext-68 YES)
(scsi1) Downloading sequencer code... 419 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.9/3.2.4
<Adaptec AHA-294X Ultra SCSI host adapter>
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.9/3.2.4
<Adaptec AHA-2944 Ultra SCSI host adapter>
scsi : 2 hosts.
Vendor: QUANTUM Model: FIREBALL_TM3200S Rev: 300X
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:0:0) Synchronous at 20.0 Mbyte/sec, offset 15.
Vendor: HP Model: C2490AM Rev: 3256
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
(scsi0:0:1:0) Synchronous at 10.0 Mbyte/sec, offset 8.
Vendor: HP Model: C1533A Rev: AN01
Type: Sequential-Access ANSI SCSI revision: 02
Detected scsi tape st0 at scsi0, channel 0, id 4, lun 0
(scsi0:0:4:0) Synchronous at 10.0 Mbyte/sec, offset 15.
Vendor: TOSHIBA Model: CD-ROM XM-5701TA Rev: 0787
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
(scsi0:0:6:0) Synchronous at 10.0 Mbyte/sec, offset 8.
Vendor: DGC Model: C1300WDR0 Rev: HP01
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdc at scsi1, channel 0, id 11, lun 0
(scsi1:0:11:0) Synchronous at 20.0 Mbyte/sec, offset 8.
Vendor: DGC Model: C1300WDR0 Rev: HP01
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdd at scsi1, channel 0, id 11, lun 1
Vendor: DGC Model: C1300WDR0 Rev: HP01
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sde at scsi1, channel 0, id 12, lun 0
(scsi1:0:12:0) Synchronous at 20.0 Mbyte/sec, offset 8.
scsi : detected 1 SCSI tape 1 SCSI cdrom 5 SCSI disks total.
.
.
ad1848/cs4248 codec driver Copyright (C) by Hannu Savolainen 1993-1996
Gravis Ultrasound audio driver Copyright (C) by Hannu Savolainen 1993-1996
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/