Since it occurs right after the ide probing and locks the machine, I
can't save it and ksymoops it.
Pre6-ac1 and pre7 both work fine with this enabled. They display
"ide_setup: hdd=ide-scsi" during bootup.
Here are the boot messages from pre7-ac2 (run without the offending
option, of course)
Compiled with pgcc 1.1 with -march=pentiumpro
Linux version 2.2.0-pre7-ac2 (root@saturne.hexanet.fr) (gcc version
pgcc-2.91.57 19980901 (egcs-1.1 release)) #8 ven jan 15 00:23:59 CET
1999
Detected 451028373 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 450.56 BogoMIPS
Memory: 128188k/131072k available (668k kernel code, 412k reserved,
1760k data, 44k init)
CPU: Intel Celeron (Mendocino) stepping 00
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.26 (19981001) Richard Gooch (rgooch@atnf.csiro.au)
PCI: PCI BIOS revision 2.10 entry at 0xfb300
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
Starting kswapd v 1.5
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.9)
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hda: FUJITSU MPC3043AT, ATA DISK drive
hdb: QUANTUM FIREBALL_TM3840A, ATA DISK drive
hdc: CD-524E, ATAPI CDROM drive
hdd: HP CD-Writer+ 7200, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: FUJITSU MPC3043AT, 4125MB w/0kB Cache, CHS=525/255/63, UDMA
hdb: QUANTUM FIREBALL_TM3840A, 3681MB w/76kB Cache, CHS=935/128/63, DMA
Partition check:
hda: hda1 hda2 hda3 hda4
hdb: hdb1 hdb2 < hdb5 > hdb3 hdb4
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 44k freed
Adding Swap: 112448k swap-space (priority -1)
ne2k-pci.c:v0.99L 2/7/98 D. Becker/P. Gortmaker
http://cesdis.gsfc.nasa.gov/linux/drivers/ne2k-pci.html
ne2k-pci.c: PCI NE2000 clone 'RealTek RTL-8029' at I/O 0xe400, IRQ 12.
eth0: PCI NE2000 found at 0xe400, IRQ 12, 00:20:18:2C:30:31.
"modprobe ide-scsi" then results in:
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
scsi : 1 host.
Vendor: TEAC Model: CD-524E Rev: 3.0B
Type: CD-ROM ANSI SCSI revision: 02
Vendor: TEAC Model: CD-524E Rev: 3.0B
Type: CD-ROM ANSI SCSI revision: 02
Vendor: TEAC Model: CD-524E Rev: 3.0B
Type: CD-ROM ANSI SCSI revision: 02
Vendor: TEAC Model: CD-524E Rev: 3.0B
Type: CD-ROM ANSI SCSI revision: 02
Vendor: TEAC Model: CD-524E Rev: 3.0B
Type: CD-ROM ANSI SCSI revision: 02
Vendor: TEAC Model: CD-524E Rev: 3.0B
Type: CD-ROM ANSI SCSI revision: 02
Vendor: TEAC Model: CD-524E Rev: 3.0B
Type: CD-ROM ANSI SCSI revision: 02
Vendor: TEAC Model: CD-524E Rev: 3.0B
Type: CD-ROM ANSI SCSI revision: 02
Vendor: HP Model: CD-Writer+ 7200 Rev: 3.01
Type: CD-ROM ANSI SCSI revision: 02
Vendor: HP Model: CD-Writer+ 7200 Rev: 3.01
Type: CD-ROM ANSI SCSI revision: 02
Vendor: HP Model: CD-Writer+ 7200 Rev: 3.01
Type: CD-ROM ANSI SCSI revision: 02
Vendor: HP Model: CD-Writer+ 7200 Rev: 3.01
Type: CD-ROM ANSI SCSI revision: 02
Vendor: HP Model: CD-Writer+ 7200 Rev: 3.01
Type: CD-ROM ANSI SCSI revision: 02
Vendor: HP Model: CD-Writer+ 7200 Rev: 3.01
Type: CD-ROM ANSI SCSI revision: 02
Vendor: HP Model: CD-Writer+ 7200 Rev: 3.01
Type: CD-ROM ANSI SCSI revision: 02
Vendor: HP Model: CD-Writer+ 7200 Rev: 3.01
Type: CD-ROM ANSI SCSI revision: 02
My .config:
#
# Automatically generated make config: don't edit
#
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
CONFIG_M686=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_SMP is not set
#
# Loadable module support
#
CONFIG_MODULES=y
# CONFIG_MODVERSIONS is not set
CONFIG_KMOD=y
#
# General setup
#
CONFIG_NET=y
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_QUIRKS=y
# CONFIG_PCI_OPTIMIZE is not set
CONFIG_PCI_OLD_PROC=y
# CONFIG_MCA is not set
CONFIG_SYSVIPC=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
# CONFIG_BINFMT_JAVA is not set
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
# CONFIG_PARPORT_OTHER is not set
CONFIG_APM=y
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
# CONFIG_APM_DO_ENABLE is not set
CONFIG_APM_CPU_IDLE=y
# CONFIG_APM_DISPLAY_BLANK is not set
CONFIG_APM_POWER_OFF=y
# CONFIG_APM_IGNORE_MULTIPLE_SUSPEND is not set
# CONFIG_APM_IGNORE_SUSPEND_BOUNCE is not set
# CONFIG_APM_RTC_IS_GMT is not set
# CONFIG_APM_ALLOW_INTS is not set
#
# Plug and Play support
#
CONFIG_PNP=y
CONFIG_PNP_PARPORT=m
#
# Block devices
#
CONFIG_BLK_DEV_FD=m
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_BLK_DEV_IDECD=m
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=m
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_VIA82C586 is not set
# CONFIG_BLK_DEV_CMD646 is not set
# CONFIG_IDE_CHIPSETS is not set
#
# Additional Block Devices
#
CONFIG_BLK_DEV_LOOP=m
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_MD is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_BLK_DEV_XD is not set
CONFIG_PARIDE_PARPORT=m
# CONFIG_PARIDE is not set
# CONFIG_BLK_DEV_HD is not set
#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_NETLINK is not set
CONFIG_FIREWALL=y
# CONFIG_NET_ALIAS is not set
# CONFIG_FILTER is not set
CONFIG_UNIX=y
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
CONFIG_IP_FIREWALL=y
CONFIG_IP_ALWAYS_DEFRAG=y
# CONFIG_IP_TRANSPARENT_PROXY is not set
CONFIG_IP_MASQUERADE=y
#
# Protocol-specific masquerading support will be built as modules.
#
CONFIG_IP_MASQUERADE_ICMP=y
#
# Protocol-specific masquerading support will be built as modules.
#
# CONFIG_IP_MASQUERADE_MOD is not set
# CONFIG_IP_ROUTER is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_ALIAS is not set
CONFIG_SYN_COOKIES=y
#
# (it is safe to leave these untouched)
#
# CONFIG_INET_RARP is not set
CONFIG_IP_NOSR=y
CONFIG_SKB_LARGE=y
# CONFIG_IPV6 is not set
#
#
#
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_BRIDGE is not set
# CONFIG_LLC is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
# CONFIG_CPU_IS_SLOW is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# SCSI support
#
CONFIG_SCSI=m
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=m
# CONFIG_CHR_DEV_ST is not set
CONFIG_BLK_DEV_SR=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
#
# SCSI low-level drivers
#
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
# CONFIG_SCSI_AIC7XXX is not set
CONFIG_SCSI_ADVANSYS=m
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_G_NCR5380_PORT is not set
# CONFIG_SCSI_G_NCR5380_MEM is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_NCR53C8XX is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_DEBUG is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
CONFIG_DUMMY=m
# CONFIG_EQUALIZER is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_RTL8139 is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_EISA=y
# CONFIG_PCNET32 is not set
# CONFIG_ACENIC is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_CS89x0 is not set
# CONFIG_DE4X5 is not set
# CONFIG_DEC_ELCP is not set
# CONFIG_DGRS is not set
# CONFIG_EEXPRESS_PRO100 is not set
# CONFIG_LNE390 is not set
# CONFIG_NE3210 is not set
CONFIG_NE2K_PCI=m
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_ES3210 is not set
# CONFIG_EPIC100 is not set
# CONFIG_ZNET is not set
# CONFIG_NET_POCKET is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
#
# Appletalk devices
#
CONFIG_PLIP=m
CONFIG_PPP=m
#
# CCP compressors for PPP are only built as modules.
#
# CONFIG_SLIP is not set
# CONFIG_NET_RADIO is not set
#
# Token ring devices
#
# CONFIG_TR is not set
# CONFIG_RCPCI is not set
CONFIG_SHAPER=m
#
# Wan interfaces
#
# CONFIG_HOSTESS_SV11 is not set
# CONFIG_COSA is not set
# CONFIG_DLCI is not set
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA subsystem support
#
# CONFIG_IRDA is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# CD-ROM drivers (not for SCSI or IDE/ATAPI drives)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_SERIAL=y
# CONFIG_SERIAL_CONSOLE is not set
# CONFIG_SERIAL_EXTENDED is not set
# CONFIG_SERIAL_NONSTANDARD is not set
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
CONFIG_PRINTER=m
CONFIG_PRINTER_READBACK=y
CONFIG_MOUSE=y
#
# Mice
#
# CONFIG_ATIXL_BUSMOUSE is not set
# CONFIG_BUSMOUSE is not set
# CONFIG_MS_BUSMOUSE is not set
CONFIG_PSMOUSE=y
# CONFIG_82C710_MOUSE is not set
# CONFIG_PC110_PAD is not set
# CONFIG_QIC02_TAPE is not set
# CONFIG_WATCHDOG is not set
# CONFIG_NVRAM is not set
# CONFIG_RTC is not set
#
# Video For Linux
#
CONFIG_VIDEO_DEV=m
CONFIG_RADIO_RTRACK=m
# CONFIG_RADIO_RTRACK2 is not set
# CONFIG_RADIO_AZTECH is not set
# CONFIG_RADIO_MIROPCM20 is not set
# CONFIG_RADIO_GEMTEK is not set
# CONFIG_VIDEO_BT848 is not set
# CONFIG_VIDEO_BWQCAM is not set
# CONFIG_VIDEO_CQCAM is not set
# CONFIG_VIDEO_PMS is not set
# CONFIG_VIDEO_SAA5249 is not set
# CONFIG_RADIO_SF16FMI is not set
# CONFIG_RADIO_ZOLTRIX is not set
#
# Joystick support
#
CONFIG_JOYSTICK=m
CONFIG_JOY_ANALOG=m
# CONFIG_JOY_ASSASIN is not set
# CONFIG_JOY_GRAVIS is not set
# CONFIG_JOY_LOGITECH is not set
# CONFIG_JOY_SIDEWINDER is not set
# CONFIG_JOY_THRUSTMASTER is not set
# CONFIG_JOY_LIGHTNING is not set
# CONFIG_JOY_CONSOLE is not set
# CONFIG_JOY_DB9 is not set
# CONFIG_JOY_TURBOGRAFX is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
# CONFIG_FT_NORMAL_DEBUG is not set
# CONFIG_FT_FULL_DEBUG is not set
# CONFIG_FT_NO_TRACE is not set
# CONFIG_FT_NO_TRACE_AT_ALL is not set
# CONFIG_FT_STD_FDC is not set
# CONFIG_FT_MACH2 is not set
# CONFIG_FT_PROBE_FC10 is not set
# CONFIG_FT_ALT_FDC is not set
#
# Filesystems
#
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS_FS is not set
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
# CONFIG_UMSDOS_FS is not set
CONFIG_VFAT_FS=m
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
# CONFIG_MINIX_FS is not set
# CONFIG_NTFS_FS is not set
# CONFIG_HPFS_FS is not set
CONFIG_PROC_FS=y
CONFIG_DEVPTS_FS=m
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_EXT2_FS=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
# CONFIG_CODA_FS is not set
CONFIG_NFS_FS=m
# CONFIG_NFSD is not set
CONFIG_SUNRPC=m
CONFIG_LOCKD=m
CONFIG_SMB_FS=m
CONFIG_SMB_WIN95=y
# CONFIG_NCP_FS is not set
#
# Partition Types
#
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MAC_PARTITION is not set
# CONFIG_SMD_DISKLABEL is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
CONFIG_NLS=y
#
# Native Language Support
#
CONFIG_NLS_CODEPAGE_437=m
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=m
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
CONFIG_NLS_ISO8859_1=m
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
#
# Console drivers
#
CONFIG_VGA_CONSOLE=y
CONFIG_VIDEO_SELECT=y
# CONFIG_MDA_CONSOLE is not set
CONFIG_FB=y
CONFIG_DUMMY_CONSOLE=y
# CONFIG_FB_VESA is not set
CONFIG_VIDEO_SELECT=y
CONFIG_FB_MATROX=m
# CONFIG_FB_MATROX_MILLENIUM is not set
# CONFIG_FB_MATROX_MYSTIQUE is not set
CONFIG_FB_MATROX_G100=y
# CONFIG_FB_MATROX_MULTIHEAD is not set
# CONFIG_FB_PCI_ATY is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FB_ATY is not set
CONFIG_FBCON_ADVANCED=y
# CONFIG_FBCON_MFB is not set
# CONFIG_FBCON_CFB2 is not set
# CONFIG_FBCON_CFB4 is not set
CONFIG_FBCON_CFB8=m
CONFIG_FBCON_CFB16=m
CONFIG_FBCON_CFB24=m
CONFIG_FBCON_CFB32=m
# CONFIG_FBCON_AFB is not set
# CONFIG_FBCON_ILBM is not set
# CONFIG_FBCON_IPLAN2P2 is not set
# CONFIG_FBCON_IPLAN2P4 is not set
# CONFIG_FBCON_IPLAN2P8 is not set
# CONFIG_FBCON_MAC is not set
# CONFIG_FBCON_VGA is not set
# CONFIG_FBCON_FONTWIDTH8_ONLY is not set
# CONFIG_FBCON_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
#
# Sound
#
# CONFIG_SOUND is not set
#
# Kernel hacking
#
CONFIG_MAGIC_SYSRQ=y
/--------------------------------------\
| Renaud Guerin - renaudg@hexanet.fr |
| rguerin@iut-info.ens.univ-reims.fr |
| http://www.hexanet.fr/~renaudg |
| CS student (Reims,France) |
| Linux supporter http://www.linux.org |
\--------------------------------------/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/