>Hello,
>> Hi All, I've bought new motherboard based on VIA MVP3 chipset
>> with ACPI interface & GL518 sensor chip, but I could not start monitoring
>> software due to absend apropriate device in list of PCI devices. If I enable
>> disabled for irq line saving USB it's apear in PCI list together with ACPI
>> interface. I looked in kernel code & found that if one function on mult-function
>> PCI device disabled all further function on this device is not checked. In my
>> case disabling USB (bus 0, dev 7, func 2) lead to lost ACPI interface
>> (bus 0, dev 7, func 3). After removing this line from pci.c file all works fine:
> Hmmm, another broken PCI device :-((
> Can you send me 'lspci -vvx -MH1' output, please?
Of course. Unknown device in the end of list its S3 Trio3D2X based on
S3 86C362 chip. I think it have to be added to next release of lspci, and,
possibly, to oldproc stuff in kernel.
00:00.0 Host bridge: VIA Technologies, Inc. VT82C597 [Apollo VP3] (rev 04)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 16 set
Region 0: Memory at e0000000 (32-bit, prefetchable)
Capabilities: [a0] AGP version 1.0
Status: RQ=7 SBA+ 64bit- FW- Rate=1
Command: RQ=7 SBA+ AGP- 64bit- FW- Rate=1
00: 06 11 97 05 06 00 90 82 04 00 00 06 00 10 00 00
10: 08 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: e8000000-efffffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00: 06 11 98 85 07 00 20 22 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 d0 d0 00 00
20: 00 e8 f0 ef f0 ff 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0c 00
## 00.01:0 is a bridge from 00 to 01-01
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C586 ISA [Apollo VP] (rev 47)
Subsystem: Unknown device 1106:0000
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
00: 06 11 86 05 8f 00 00 02 47 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 06) (prog-if 8a)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set
Region 4: I/O ports at e000
00: 06 11 71 05 07 00 80 02 06 8a 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.3 Host bridge: VIA Technologies, Inc. VT82C586B ACPI (rev 10)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00: 06 11 40 30 00 00 80 02 10 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01:00.0 VGA compatible controller: S3 Inc.: Unknown device 8a13 (rev 01)
Subsystem: Unknown device 5333:8a13
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 4 min, 255 max, 32 set
Interrupt: pin ? routed to IRQ 255
Region 0: Memory at e8000000 (32-bit, non-prefetchable)
Capabilities: [dc] Power Management version 1
Flags: PMEClk- AuxPwr- DSI+ D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] AGP version 1.0
Status: RQ=31 SBA- 64bit- FW- Rate=21
Command: RQ=31 SBA- AGP- 64bit- FW- Rate=21
00: 33 53 13 8a 07 00 10 02 01 00 00 03 00 20 00 00
10: 00 00 00 e8 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 33 53 13 8a
30: 00 00 00 00 dc 00 00 00 00 00 00 00 ff 00 04 ff
Summary of buses:
00: Primary host bus
01.0 Bridge to 01-01
01: Entered via 00:01.0
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/