I recently purchased a Hauppage WinTV model 401 with tv/radio support.
It is based on the Brooktree bt878 chipset which is supported by the
bttv video4linux drivers in 2.2.10 according to the documentation. I
installed my board, it works flawlessly under windows nt. I decided to
get it working in linux considering that is my primary environment,
I set up conf.modules to load bttv and tuner via these parameters
alias char-major-81 bttv
options bttv card=10 radio=1
pre-install bttv modprobe -k tuner type=5
when i run xawtv, xawtv segfaults and I get a kernel oops, same kernel
oops if i modprobe tuner and bttv manually.
Aug 23 22:18:59 roxen kernel: Linux video capture interface: v1.00
Aug 23 22:18:59 roxen kernel: i2c: initialized
Aug 23 22:18:59 roxen kernel: i2c: driver i2c character device
registered.
Aug 23 22:18:59 roxen kernel: i2c char device interface initialized.
Aug 23 22:19:00 roxen kernel: bttv0: Brooktree Bt878 (rev 2) bus: 0,
devfn: 144,
irq: 18, memory: 0xfc9fe000.
Aug 23 22:19:00 roxen kernel: bttv: 1 Bt8xx card(s) found.
Aug 23 22:19:00 roxen kernel: bttv0: Hauppauge eeprom: tuner=Philips
FM1236 (2)
Aug 23 22:19:00 roxen kernel: bttv0: audio chip: TDA9850
Aug 23 22:19:00 roxen kernel: bttv0: NO fader chip: TEA6300
Aug 23 22:19:00 roxen kernel: bttv0: model: BT878(Hauppauge new)
Aug 23 22:19:00 roxen kernel: bttv0: PLL: 28636363 => 35468950 ... ok
Aug 23 22:19:00 roxen kernel: Unable to handle kernel NULL pointer
dereference at virtual address 00000008
Aug 23 22:19:00 roxen kernel: current->tss.cr3 = 0fe29000, %cr3 =
0fe29000
Aug 23 22:19:00 roxen kernel: *pde = 00000000
Aug 23 22:19:00 roxen kernel: Oops: 0000
Aug 23 22:19:00 roxen kernel: CPU: 0
Aug 23 22:19:00 roxen kernel: EIP: 0010:[<d0832101>]
Aug 23 22:19:00 roxen kernel: EFLAGS: 00010286
Aug 23 22:19:00 roxen kernel: eax: d083d7e0 ebx: cd0281a0 ecx:
00000000 ed
x: 00000000
Aug 23 22:19:00 roxen kernel: esi: 00000002 edi: d08347ac ebp:
d083d680 es
p: cd77da4c
Aug 23 22:19:00 roxen kernel: ds: 0018 es: 0018 ss: 0018
Aug 23 22:19:00 roxen kernel: Process xawtv (pid: 429, process nr: 37,
stackpage
=cd77d000)
Aug 23 22:19:00 roxen kernel: Stack: d08347ac d083d680 d083ccdc c01101f8
0000000
0 d0834157 d083d7e0 000000c2
Aug 23 22:19:00 roxen kernel: 00000002 0000006f 00000001 cd77daac
d083ccc
8 d0837cec cd028100 bffffc08
Aug 23 22:19:00 roxen kernel: cd77db20 cd77daac 00000022 08090700
cd77ddd
4 d08344a5 cd028100 00000000
Aug 23 22:19:00 roxen kernel: Call Trace: [<d08347ac>] [<d083d680>]
[<d083ccdc>]
[do_edge_ioapic_IRQ+120/168] [<d0834157>] [<d083d7e0>] [<d083ccc8>]
Aug 23 22:19:00 roxen kernel: [<d0837cec>] [<d08344a5>]
[<d082e652>] [<d0
83d680>] [<d08380ab>] [<d083d680>] [smp_reschedule_interrupt+8/12]
[<d0838120>]
Aug 23 22:19:00 roxen kernel: [<d083d7e0>] [<d083d680>]
[<d0839636>] [<d0
83d680>] [<d083d78c>] [requeue_sd_request+3217/3232]
[get_hash_table+29/44] [__b
relse+28/104]
Aug 23 22:19:00 roxen kernel: [__brelse+19/104]
[block_getblk+214/768] [w
ake_up_process+88/108] [ext2_getblk+527/540] [__brelse+28/104]
[kfree_skbmem+60/
76] [ext2_find_entry+597/784] [clear_IO_APIC+39/44]
Aug 23 22:19:00 roxen kernel: [wake_up_process+88/108]
[alloc_skb+139/256
] [reschedule_idle+420/448] [sock_wmalloc+41/84]
[sock_def_readable+45/56] [unix
_stream_write_space+28/72] [kfree_skbmem+60/76] [sock_wfree+29/36]
Aug 23 22:19:00 roxen kernel: [memcpy_toiovec+60/104]
[__kfree_skb+174/18
4] [unix_stream_recvmsg+764/900] [sock_recvmsg+65/184]
[sock_read+132/148] [<d082c229>] [<d083d680>] [schedule+497/972]
Aug 23 22:19:00 roxen kernel: [sys_ioctl+375/424]
[system_call+52/56]
Aug 23 22:19:00 roxen kernel: Code: 8b 52 08 0f b6 52 2a 8b 78 54 3b 15
40 27 83 d0 72 1d 83 c4
lspci -vv
00:12.0 Multimedia video controller: Brooktree Corporation Bt878 (rev
02)
Subsystem: Unknown device 0070:13eb
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 16 min, 40 max, 64 set
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fc9fe000 (32-bit, prefetchable)
00:12.1 Multimedia controller: Brooktree Corporation Bt878 (rev 02)
Subsystem: Unknown device 0070:13eb
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 4 min, 255 max, 64 set
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fc9ff000 (32-bit, prefetchable)
This machine is a dual pIII/550 on a tyan tiger 100
I am also using the i2c based lmsensors package if that makes any
difference(i2c conflicts)?
here is my kernel config
#
# Automatically generated make config: don't edit
#
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
CONFIG_M686=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
CONFIG_SMP=y
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODVERSIONS=y
CONFIG_KMOD=y
#
# General setup
#
CONFIG_NET=y
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
# CONFIG_PCI_QUIRKS is not set
# CONFIG_PCI_OLD_PROC is not set
# CONFIG_MCA is not set
# CONFIG_VISWS is not set
CONFIG_X86_IO_APIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_SYSVIPC=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_BINFMT_AOUT is not set
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=y
# CONFIG_BINFMT_JAVA is not set
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
# CONFIG_PARPORT_OTHER is not set
# CONFIG_APM is not set
#
# Plug and Play support
#
# CONFIG_PNP is not set
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
CONFIG_BLK_DEV_IDE=m
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=m
CONFIG_BLK_DEV_IDECD=m
# CONFIG_BLK_DEV_IDETAPE is not set
CONFIG_BLK_DEV_IDEFLOPPY=m
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_VIA82C586 is not set
# CONFIG_BLK_DEV_CMD646 is not set
# CONFIG_IDE_CHIPSETS is not set
#
# Additional Block Devices
#
CONFIG_BLK_DEV_LOOP=m
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_MD is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_BLK_DEV_XD is not set
CONFIG_PARIDE_PARPORT=m
# CONFIG_PARIDE is not set
# CONFIG_BLK_DEV_HD is not set
#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_NETLINK is not set
CONFIG_FIREWALL=y
# CONFIG_FILTER is not set
CONFIG_UNIX=y
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
CONFIG_IP_FIREWALL=y
# CONFIG_IP_ALWAYS_DEFRAG is not set
# CONFIG_IP_ROUTER is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_ALIAS is not set
# CONFIG_SYN_COOKIES is not set
#
# (it is safe to leave these untouched)
#
# CONFIG_INET_RARP is not set
CONFIG_SKB_LARGE=y
# CONFIG_IPV6 is not set
#
#
#
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_BRIDGE is not set
# CONFIG_LLC is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
# CONFIG_CPU_IS_SLOW is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# SCSI support
#
CONFIG_SCSI=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_ST=m
CONFIG_BLK_DEV_SR=y
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=y
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
#
# SCSI low-level drivers
#
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
CONFIG_SCSI_AIC7XXX=y
CONFIG_AIC7XXX_TCQ_ON_BY_DEFAULT=y
CONFIG_AIC7XXX_CMDS_PER_DEVICE=8
# CONFIG_AIC7XXX_PROC_STATS is not set
CONFIG_AIC7XXX_RESET_DELAY=5
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_NCR53C8XX is not set
# CONFIG_SCSI_SYM53C8XX is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_DEBUG is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
# CONFIG_ARCNET is not set
CONFIG_DUMMY=m
CONFIG_EQUALIZER=m
CONFIG_NET_ETHERNET=y
CONFIG_NET_VENDOR_3COM=y
# CONFIG_EL1 is not set
# CONFIG_EL2 is not set
# CONFIG_ELPLUS is not set
# CONFIG_EL16 is not set
# CONFIG_EL3 is not set
# CONFIG_3C515 is not set
CONFIG_VORTEX=m
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_RTL8139 is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_ACENIC is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_EISA=y
# CONFIG_PCNET32 is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_CS89x0 is not set
# CONFIG_DE4X5 is not set
CONFIG_DEC_ELCP=m
# CONFIG_DGRS is not set
CONFIG_EEXPRESS_PRO100=m
# CONFIG_LNE390 is not set
# CONFIG_NE3210 is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_ES3210 is not set
# CONFIG_EPIC100 is not set
# CONFIG_ZNET is not set
# CONFIG_NET_POCKET is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_DLCI is not set
CONFIG_PLIP=m
CONFIG_PPP=m
#
# CCP compressors for PPP are only built as modules.
#
CONFIG_SLIP=m
# CONFIG_SLIP_COMPRESSED is not set
# CONFIG_SLIP_SMART is not set
# CONFIG_SLIP_MODE_SLIP6 is not set
# CONFIG_NET_RADIO is not set
# CONFIG_TR is not set
CONFIG_SHAPER=m
# CONFIG_HOSTESS_SV11 is not set
# CONFIG_COSA is not set
# CONFIG_RCPCI is not set
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA subsystem support
#
# CONFIG_IRDA is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_SERIAL=y
# CONFIG_SERIAL_CONSOLE is not set
# CONFIG_SERIAL_EXTENDED is not set
# CONFIG_SERIAL_NONSTANDARD is not set
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
CONFIG_PRINTER=m
CONFIG_PRINTER_READBACK=y
CONFIG_MOUSE=y
#
# Mice
#
# CONFIG_ATIXL_BUSMOUSE is not set
# CONFIG_BUSMOUSE is not set
# CONFIG_MS_BUSMOUSE is not set
CONFIG_PSMOUSE=y
# CONFIG_82C710_MOUSE is not set
# CONFIG_PC110_PAD is not set
# CONFIG_QIC02_TAPE is not set
# CONFIG_WATCHDOG is not set
# CONFIG_NVRAM is not set
# CONFIG_RTC is not set
#
# Video For Linux
#
CONFIG_VIDEO_DEV=m
# CONFIG_RADIO_RTRACK is not set
# CONFIG_RADIO_RTRACK2 is not set
# CONFIG_RADIO_AZTECH is not set
# CONFIG_RADIO_CADET is not set
# CONFIG_RADIO_MIROPCM20 is not set
# CONFIG_RADIO_GEMTEK is not set
CONFIG_VIDEO_BT848=m
# CONFIG_VIDEO_BWQCAM is not set
# CONFIG_VIDEO_CQCAM is not set
# CONFIG_VIDEO_PMS is not set
# CONFIG_VIDEO_SAA5249 is not set
# CONFIG_RADIO_SF16FMI is not set
# CONFIG_RADIO_TYPHOON is not set
# CONFIG_RADIO_ZOLTRIX is not set
#
# Joystick support
#
# CONFIG_JOYSTICK is not set
# CONFIG_DTLK is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
#
# Filesystems
#
CONFIG_QUOTA=y
CONFIG_AUTOFS_FS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
# CONFIG_UMSDOS_FS is not set
CONFIG_VFAT_FS=m
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_MINIX_FS=y
CONFIG_NTFS_FS=m
# CONFIG_NTFS_RW is not set
# CONFIG_HPFS_FS is not set
CONFIG_PROC_FS=y
CONFIG_DEVPTS_FS=y
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_EXT2_FS=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
# CONFIG_CODA_FS is not set
CONFIG_NFS_FS=m
CONFIG_NFSD=m
# CONFIG_NFSD_SUN is not set
CONFIG_SUNRPC=m
CONFIG_LOCKD=m
CONFIG_SMB_FS=m
# CONFIG_NCP_FS is not set
#
# Partition Types
#
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MAC_PARTITION is not set
# CONFIG_SMD_DISKLABEL is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
CONFIG_NLS=y
#
# Native Language Support
#
CONFIG_NLS_CODEPAGE_437=m
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
CONFIG_NLS_ISO8859_1=m
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
#
# Console drivers
#
CONFIG_VGA_CONSOLE=y
# CONFIG_VIDEO_SELECT is not set
# CONFIG_MDA_CONSOLE is not set
# CONFIG_FB is not set
#
# Sound
#
CONFIG_SOUND=m
# CONFIG_SOUND_ES1370 is not set
# CONFIG_SOUND_ES1371 is not set
# CONFIG_SOUND_SONICVIBES is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_OSS is not set
#
# Kernel hacking
#
CONFIG_MAGIC_SYSRQ=y
If you need any other information please ask
I hope this leads to a fix, i would really love to use this card under
linux.
Thanks in advance,
-- Cody Pisto | cpisto@flash.net President, | HPC Solutions, Inc. | http://www.hpc-solutions.com Debian/GNU Linux http://www.debian.org Developer Use the source luke.- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu Please read the FAQ at http://www.tux.org/lkml/