Can't seem to get my drives (2x maxtor 91024u4) to use udma66
and I get some strange messages while booting. This is on an Abit BP6
with Linux 2.2.12 smp with the ide.2.2.12.19991003 patch.
[snip]
Uniform Multi-Platform E-IDE driver Revision: 6.20
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
HPT366: onboard version of chipset, pin1=1 pin2=2
PCI: HPT366: Fixing interrupt 11 pin 2 to ZERO
HPT366: IDE controller on PCI bus 00 dev 98
HPT366: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0xdc00-0xdc07, BIOS settings: hde:DMA, hdf:DMA
hda: 40X PCA403CD, ATAPI CDROM drive
hde: Maxtor 91024U4, ATA DISK drive
hdf: Maxtor 91024U4, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2 at 0xd400-0xd407,0xd802 on irq 11
hde: config_chipset_for_pio
hde: config_chipset_for_pio: speed=0x000c
hpt366_tune_chipset(hde, speed=0x0c)
pci_bus_clock_list(speed=0x0c, table=c01fc42c)
pci_bus_clock_list: found match: 0xc0c8a731
hde: speed=0x0c(PIO 4), drive0, old=0x90c9a731, new=0x40c8a731, err=0x0000
hde: Maxtor 91024U4, 9765MB w/2048kB Cache, CHS=19841/16/63
hdf: config_chipset_for_pio
hdf: config_chipset_for_pio: speed=0x000c
hpt366_tune_chipset(hdf, speed=0x0c)
pci_bus_clock_list(speed=0x0c, table=c01fc42c)
pci_bus_clock_list: found match: 0xc0c8a731
hdf: speed=0x0c(PIO 4), drive1, old=0x90c9a731, new=0x40c8a731, err=0x0000
hdf: Maxtor 91024U4, 9765MB w/2048kB Cache, CHS=19841/16/63
hda: ATAPI 40X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.05
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Partition check:
hde:hde: irq timeout: status=0xd0 { Busy }
ide2: reset: success
hde1 hde2 < hde5 hde6 hde7 hde8 >
hdf: hdf1 hdf2 < hdf5 hdf6 >
VFS: Mounted root (ext2 filesystem) readonly.
[snip]
Sometimes there's also a 'bug: kernel timer added twice at c01821b1' message).
What's going on?
Please mail me also since I'm not on the list.
Regards,
Wilfred.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/